ECS: Så här kontrollerar du Arista-switchgränssnitt
Resumen: Kontrollera statussammanfattning för gränssnitt och information om alla gränssnitt för en Arista-switch. Dessa kommandon fungerar på alla har-, kanin- och sköldpaddsbrytare.
Este artículo se aplica a
Este artículo no se aplica a
Este artículo no está vinculado a ningún producto específico.
No se identifican todas las versiones del producto en este artículo.
Instrucciones
Använder svc_switch metod (rekommenderas)
svc_switch är tillgänglig från och med xDoctor 82. Se till att alltid använda den senaste xDoctor-versionen för bästa resultat. Kommandona nedan får samma utdata som visas i avsnittet med äldre metoder nedan
Kommandon:
# svc_switch fe port_status
# svc_switch vara port_status
# svc_switch fe port_status
# svc_switch vara port_status
Utökade kommandon:
# svc_switch fe cmd -hare "sh int status"
# svc_switch fe cmd -rabbit "sh int status"
# svc_switch vara cmd "sh int status"
Exempel:
# svc_switch fe cmd -hare "sh int status"
# svc_switch fe cmd -rabbit "sh int status"
# svc_switch vara cmd "sh int status"
Exempel:
admin@ecs-n1:~> svc_switch fe port_status
svc_switch v1.2.3 (svc_tools v2.5.1) Started 2022-07-15 20:20:42
Ethernet Port Peer Port Status Speed Duplex
Rabbit Hare Rabbit Hare Rabbit Hare
---------------------------------------------------------------------------------------------
Et1 notconnect notconnect full full 10G 10G
Et2 notconnect notconnect full full 10G 10G
Et3 notconnect notconnect full full 10G 10G
Et4 notconnect notconnect full full 10G 10G
Et8 connected notconnect a-full auto a-1G auto
Et9 r1n1 connected connected full full 10G 10G
Et10 r1n2 connected connected full full 10G 10G
Et11 r1n3 connected connected full full 10G 10G
Et12 r1n4 connected connected full full 10G 10G
Et13 r1n5 connected connected full full 10G 10G
Et45 <peer switch> connected connected full full 10G 10G
Et46 <peer switch> connected connected full full 10G 10G
Et47 <peer switch> connected connected full full 10G 10G
Et48 <peer switch> connected connected full full 10G 10G
admin@ecs-n1:~>
Kontrollera en viss switchport genom att
Kommando:
# svc_switch <fe/be> cmd -hare "sh int <gränssnitt>"
Exempel:
admin@ecs-n1:~> svc_switch fe cmd -hare "sh int Ethernet 9"
svc_switch v1.2.3 (svc_tools v2.5.1) Started 2022-07-15 20:22:12
Switch: hare.rack
Ethernet9 is up, line protocol is up (connected)
Hardware is Ethernet, address is 2899.3af4.e099 (bia 2899.3af4.e099)
Description: MLAG group 1
Member of Port-Channel1
Ethernet MTU 9214 bytes , BW 10000000 kbit
Full-duplex, 10Gb/s, auto negotiation: off, uni-link: n/a
Up 16 days, 11 hours, 11 minutes, 33 seconds
Loopback Mode : None
143 link status changes since last clear
Last clearing of "show interface" counters never
5 minutes input rate 4.39 Mbps (0.0% with framing overhead), 900 packets/sec
5 minutes output rate 3.93 Mbps (0.0% with framing overhead), 837 packets/sec
14816317766 packets input, 10767089176347 bytes
Received 195138 broadcasts, 791536 multicast
0 runts, 0 giants
0 input errors, 0 CRC, 0 alignment, 0 symbol, 0 input discards
121 PAUSE input
15450395319 packets output, 12027987949137 bytes
Sent 591418 broadcasts, 7471144 multicast
0 output errors, 0 collisions
0 late collision, 0 deferred, 111784 output discards
0 PAUSE output
admin@ecs-n1:~>
Information om tolkning av utdata finns i följande avsnitt
: Befintlig metod
- Secure Shell till switchen som kräver verifiering
Kommandot:
# ssh-switchnamn.rack <>
# ssh-switchnamn.rack <>
- Kör kommandot nedan för att få en allmän översikt över alla gränssnitt
Kommandot:
# sh gränssnittsstatus
Exempel:
# sh gränssnittsstatus
Exempel:
hare#sh interfaces status Port Name Status Vlan Duplex Speed Type Flags Et1 MLAG group 100 connected in Po100 full 10G 10GBASE-SRL Et2 MLAG group 100 connected in Po100 full 10G 10GBASE-SRL Et3 MLAG group 100 notconnect in Po100 full 10G 10GBASE-SRL Et4 MLAG group 100 notconnect in Po100 full 10G Not Present Et5 MLAG group 100 notconnect in Po100 full 10G Not Present Et6 MLAG group 100 notconnect in Po100 full 10G Not Present Et7 MLAG group 100 notconnect in Po100 full 10G Not Present Et8 MLAG group 100 notconnect in Po100 auto auto 1000BASE-T Et9 MLAG group 1 connected in Po1 full 10G 10GBASE-CRA Et10 MLAG group 2 connected in Po2 full 10G 10GBASE-CRA Et11 MLAG group 3 connected in Po3 full 10G 10GBASE-CRA Et12 MLAG group 4 connected in Po4 full 10G 10GBASE-CRA Et13 MLAG group 5 connected in Po5 full 10G 10GBASE-CRA Et14 MLAG group 6 connected in Po6 full 10G 10GBASE-CRA Et15 MLAG group 7 connected in Po7 full 10G 10GBASE-CRA Et16 MLAG group 8 connected in Po8 full 10G 10GBASE-CRA Et17 MLAG group 9 notconnect in Po9 full 10G Not Present Et18 MLAG group 10 notconnect in Po10 full 10G Not Present Et19 MLAG group 11 notconnect in Po11 full 10G Not Present Et20 MLAG group 12 notconnect in Po12 full 10G Not Present Et21 MLAG group 13 notconnect in Po13 full 10G Not Present Et22 MLAG group 14 notconnect in Po14 full 10G Not Present Et23 MLAG group 15 notconnect in Po15 full 10G Not Present Et24 MLAG group 16 notconnect in Po16 full 10G Not Present Et25 MLAG group 17 notconnect in Po17 full 10G Not Present Et26 MLAG group 18 notconnect in Po18 full 10G Not Present Et27 MLAG group 19 notconnect in Po19 full 10G Not Present Et28 MLAG group 20 notconnect in Po20 full 10G Not Present Et29 MLAG group 21 notconnect in Po21 full 10G Not Present Et30 MLAG group 22 notconnect in Po22 full 10G Not Present Et31 MLAG group 23 notconnect in Po23 full 10G Not Present Et32 MLAG group 24 notconnect in Po24 full 10G Not Present Et33 RESERVED notconnect 1 full 10G Not Present Et34 RESERVED notconnect 1 full 10G Not Present Et35 RESERVED notconnect 1 full 10G Not Present Et36 RESERVED notconnect 1 full 10G Not Present Et37 RESERVED notconnect 1 full 10G Not Present Et38 RESERVED notconnect 1 full 10G Not Present Et39 RESERVED notconnect 1 full 10G Not Present Et40 RESERVED notconnect 1 full 10G Not Present Et41 RESERVED notconnect 1 full 10G Not Present Et42 RESERVED notconnect 1 full 10G Not Present Et43 RESERVED notconnect 1 full 10G Not Present Et44 RESERVED notconnect 1 full 10G Not Present Et45 mlag peer connection connected in Po25 full 10G 10GBASE-CRA Et46 mlag peer connection connected in Po25 full 10G 10GBASE-CRA Et47 mlag peer connection connected in Po25 full 10G 10GBASE-CRA Et48 mlag peer connection connected in Po25 full 10G 10GBASE-CRA Et49/1 notconnect 1 full 10G Not Present Et49/2 notconnect 1 full 10G Not Present Et49/3 notconnect 1 full 10G Not Present Et49/4 notconnect 1 full 10G Not Present Et50/1 notconnect 1 full 10G Not Present Et50/2 notconnect 1 full 10G Not Present Et50/3 notconnect 1 full 10G Not Present Et50/4 notconnect 1 full 10G Not Present Et51/1 notconnect 1 full 10G Not Present Et51/2 notconnect 1 full 10G Not Present Et51/3 notconnect 1 full 10G Not Present Et51/4 notconnect 1 full 10G Not Present Et52/1 notconnect 1 full 10G Not Present Et52/2 notconnect 1 full 10G Not Present Et52/3 notconnect 1 full 10G Not Present Et52/4 notconnect 1 full 10G Not Present Ma1 connected routed a-full a-1G 10/100/1000 Po1 Nile Node01 (Data) MLAG 1 connected 2769 full 20G N/A Po2 Nile Node02 (Data) MLAG 2 connected 2769 full 20G N/A Po3 Nile Node03 (Data) MLAG 3 connected 2769 full 20G N/A Po4 Nile Node04 (Data) MLAG 4 connected 2769 full 20G N/A Po5 Nile Node05 (Data/Compute) MLAG 5 connected 2769 full 20G N/A Po6 Nile Node06 (Data/Compute) MLAG 6 connected 2769 full 20G N/A Po7 Nile Node07 (Data/Compute) MLAG 7 connected 2769 full 20G N/A Po8 Nile Node08 (Data/Compute) MLAG 8 connected 2769 full 20G N/A Po9 Nile Node09 (Compute) MLAG 9 notconnect 2769 full unconf N/A Po10 Nile Node10 (Compute) MLAG 10 notconnect 2769 full unconf N/A Po11 Nile Node11 (Compute) MLAG 11 notconnect 2769 full unconf N/A Po12 Nile Node12 (Compute) MLAG 12 notconnect 2769 full unconf N/A Po13 Nile Node13 (Compute) MLAG 13 notconnect 1 full unconf N/A Po14 Nile Node14 (Compute) MLAG 14 notconnect 1 full unconf N/A Po15 Nile Node15 (Compute) MLAG 15 notconnect 1 full unconf N/A Po16 Nile Node16 (Compute) MLAG 16 notconnect 1 full unconf N/A Po17 Nile Node17 (Compute) MLAG 17 notconnect 1 full unconf N/A Po18 Nile Node18 (Compute) MLAG 18 notconnect 1 full unconf N/A Po19 Nile Node19 (Compute) MLAG 19 notconnect 1 full unconf N/A Po20 Nile Node20 (Compute) MLAG 20 notconnect 1 full unconf N/A Po21 Nile Node21 (Compute) MLAG 21 notconnect 1 full unconf N/A Po22 Nile Node22 (Compute) MLAG 22 notconnect 1 full unconf N/A Po23 Nile Node23 (Compute) MLAG 23 notconnect 1 full unconf N/A Po24 Nile Node24 (Compute) MLAG 24 notconnect 1 full unconf N/A Po25 mlag peer connection connected trunk full 40G N/A Po100 Customer Uplink (MLAG group 100) connected 2769 full 40G N/A
MLAG-grupp 100 : Är för kundens nätverksanslutning, dessa gränssnitt är direkt anslutna till kundens switch. Minst en portupplänk måste anslutas på var och en av haren och kaninen. Status ska vara Ansluten, vilket innebär att länken är aktiv och aktiv på det fysiska lagret. Den här gruppen har flera gränssnitt grupperade tillsammans (Ethernet-portarna 1–8).
Nodanslutningar ( ET9 - ET 16) : På ett standard Gen 2-rack är varje nod 1 slave-0-gränssnitt ansluten till Rabbit-port Ethernet 9 och dess motsvarighet slav-1 är ansluten till samma port på hare. Varje nod har sin egen MLAG-grupp identifierad (1 för provo, 2 för sandy och så vidare ..) . För att säkerställa att nodlänken är uppe bör statusen vara "ansluten" på switchsidan, både Hare och Rabbit.
Ethernet 45 - 48 : Är mlag-peer-anslutningar, det är backend-anslutningar mellan Hare och Rabbit, dessa bör alltid anslutas för att säkerställa att switchaggregeringsprotokollet fungerar som förväntat.
- Specifika gränssnittskontroller (detaljerade);
För att ta en närmare titt på en enskild portdetalj kan kommandot nedan användas. Exempel nedan kontrollera ethernet9-kommandot
:
:
# sh int Ethernet 9
Exempel:
hare>sh int Ethernet 9
Ethernet9 is up, line protocol is up (connected)
Hardware is Ethernet, address is 2xxx.xxxxx.xxxx (bia 2xxx.3xxx.0xxx)
Description: MLAG group 1
Member of Port-Channel1
Ethernet MTU 9214 bytes , BW 10000000 kbit
Full-duplex, 10Gb/s, auto negotiation: off, uni-link: n/a
Up 176 days, 15 hours, 50 minutes, 16 seconds
Loopback Mode : None
64 link status changes since last clear
Last clearing of "show interface" counters never
5 minutes input rate 83.1 Mbps (0.8% with framing overhead), 10914 packets/sec
5 minutes output rate 44.4 Mbps (0.5% with framing overhead), 7915 packets/sec
2089446721845 packets input, 2396162845580046 bytes
Received 299922 broadcasts, 6615343 multicast
0 runts, 0 giants
0 input errors, 0 CRC, 0 alignment, 0 symbol, 0 input discards
9258523 PAUSE input
2234539463655 packets output, 2622737809302178 bytes
Sent 2368209 broadcasts, 59767250 multicast
0 output errors, 0 collisions
0 late collision, 0 deferred, 96470619 output discards
0 PAUSE output
Med det här kommandot kan vi titta och mer information om specifika gränssnitt:
- Portstatus ska vara ansluten, linjeprotokollet ska vara uppe. Om porten inte fungerar ur maskinvarusynpunkt kan vi se att portstatusen är nere.
- MAC-adressen kan också verifieras från dessa utdata. Det här är en unik maskinvaruadress som varje port har.
- Duplex och hastighet är viktiga att validera. Full duplex bör alltid förhandlas, halv duplex, om den ses, indikerar ett förhandlingsproblem och måste undersökas.
- Portdrifttid är användbart för att validera stabilitet, i händelse av länkklaffar kommer drifttiden att fortsätta att återställas.
- Räknare gav viktig statistik, CRC , Fel och kollisioner bör inte öka på porten. Om så är fallet indikerar det ett problem och kan påverka prestandan.
Productos afectados
ECSProductos
ECS Appliance, ECS Appliance Gen 1, ECS Appliance Gen 2, ECS Appliance Hardware Gen1 C-Series, ECS Appliance Hardware Gen2 C-Series, ECS Appliance Hardware Gen2 U-SeriesPropiedades del artículo
Número del artículo: 000180092
Tipo de artículo: How To
Última modificación: 19 dic 2022
Versión: 3
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.