Integrated Dell Remote Access Controller 9 Attribute Registry

NIC Attributes

NIC.ConfigureFormn.BusDeviceFunction[Partition:n] (Read Only)

Description

The value of this attribute depends on the state of the NParEP Mode setting. If NParEP Mode is Disabled, the value is the BIOS assigned PCIe Bus:Device:Function identifier. If NParEP Mode is Enabled, the value is the BIOS assigned PCIe Bus:Function identifier. Replace n with the number of the partition. Indicates the PCI Address of the partitions Physical Function.

Legal Values

String of up to 8 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.FCoEOffloadMode[Partition:n] (Read or Write)

Description

Enable/Disable the FCoE personality on the partition. Replace n with the number of the partition. Enables the partition for FCoE storage traffic.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.FIPMacAddr[Partition:n] (Read Only)

Description

Permanent FIP-MAC address for FCoE assigned during manufacturing. Specified on a per partition basis. Replace n with the number of the partition. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Permanent FIP-MAC address for FCoE assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.InstanceNumber[Partition:n] (Read Only)

Description

Numeric instance of the partition (e.g. 1st, 2nd, etc.) on the port it belongs to. This identifier is unique for each partition on the port. Replace n with the number of the partition. Instance Number of the partition.

Legal Values

Integer values.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.IscsiFIPMacAddr[Partition:n] (Read Only)

Description

Permanent combination MAC address for iSCSI offload and FIP for FCoE assigned during manufacturing. Specified on a per partition basis. Replace n with the number of the partition. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Permanent combination MAC address for iSCSI offload and FCoE FIP assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.IscsiMacAddr[Partition:n] (Read Only)

Description

Permanent MAC address for iSCSI offload assigned during manufacturing. Specified on a per partition basis. Replace n with the number of the partition. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Permanent MAC address for iSCSI offload assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.L2FIPMacAddr[Partition:n] (Read Only)

Description

Permanent combination Ethernet and FIP-MAC address for FCoE assigned during manufacturing. Specified on a per partition basis. Replace n with the number of the partition. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Permanent combination MAC address for Ethernet and FCoE FIP assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.L2IscsiFIPMacAddr[Partition:n] (Read Only)

Description

The Permanent combination Ethernet, iSCSI Offload and FIP for FCoE MAC address of the partition assigned during manufacturing. Replace n with the number of the partition. The current address value should be readable at all times, irrespective of feature and partition enablement. Permanent combination MAC address for Ethernet, iSCSI Offload and FCoE FIP assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.L2IscsiMacAddr[Partition:n] (Read Only)

Description

The Permanent combination Ethernet and iSCSI Offload MAC address of the partition assigned during manufacturing. Replace n with the number of the partition. The current address value should be readable at all times, irrespective of feature and partition enablement. Permanent combination MAC address for Ethernet and iSCSI Offload assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.MacAddr[Partition:n] (Read Only)

Description

The Permanent MAC address of the partition assigned during manufacturing. Replace n with the number of the partition. The current address value should be readable at all times, irrespective of feature and partition enablement. Permanent MAC address assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.NicMode[Partition:n] (Read or Write)

Description

Enable/Disable the NIC personality on the partition. Replace n with the number of the partition. Note: This personality type should be specified as the partition 1 default if RDMA is not supported or has dependencies on other device modes or settings. The default setting should be disabled for other partitions on the port. Specify use of the partition for L2-Ethernet traffic.

Legal Values

Enabled
Disabled

Default Value

Varies

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.NodeGuid[Partition:n] (Read Only)

Description

The permanent partition Node GUID assigned to the partition (PF) during manufacturing used when more than one PF is assigned to the port. The permanent Node GUID assigned to the partition during manufacturing

Legal Values

String of ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.NumberVFAdvertised[Partition:n] (Read or Write)

Description

This value is the number of PCI Virtual Functions Advertised by the partition in PCI config space when operating in the NPar+SR-IOV virtualization mode. The value of this attribute may be the same across partitions or be settable on an individual partition basis depending on implementation. Note: This attribute is only defined for the browser and does NOT have any x-UEFI mapping. VF allocation is set via the VFDistribution attribute in x-UEFI. There will be an instance of this attribute for each partition. Replace n in the AttributeName with the number of the partition. Specify the number of PCI Virtual Functions (VFs) to be advertised on this partition (PF) in PCI config space. The number of advertised VFs on each partition must add up to be less than or equal to the number of PCI Virtual Functions supported by the device or port. [VENDOR modify appropriately for the implementation].

Legal Values

Integer values from 0 to 256.

Default Value

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.NvmeTcpBusDeviceFunction[Partition:n] (Read Only)

Description

The value of this attribute depends on the state of the NParEP Mode setting. If NParEP Mode is Disabled, the value is the BIOS assigned PCIe Bus:Device:Function identifier of the NVMe/TCP PF . If NParEP Mode is Enabled, the value is the BIOS assigned PCIe Bus:Function identifier of the NVMe/TCP PF. Indicates the PCI Address of the NVMe/TCP partitions Physical Function.

Legal Values

String of up to 8 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.NvmeTcpMacAddr[Partition:n] (Read Only)

Description

Permanent MAC address for NVMe/TCP Offload operation assigned during manufacturing. If supported, the current address value should be readable at all times, irrespective of feature enablement. Permanent MAC address for NVMe/TCP assigned during manufacturing.

Legal Values

String of up to 17 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.NvmeTcpOffloadMode[Partition:n] (Read or Write)

Description

Enable/Disable the NVMe/TCP offload personality on the partition. Replace n with the number of the partition. Specify use of the partition for NVMe/TCP offload storage traffic.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.NvmeTcpPCIDeviceID[Partition:n] (Read Only)

Description

PCI Device ID reported by the NVMe/TCP PF when operating in NPar modes. PCI Device ID of the NVMe/TCP partitions Physical Function.

Legal Values

String of up to 4 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.PCIDeviceID[Partition:n] (Read Only)

Description

PCI Device ID of the partition. Replace n with the number of the partition. PCI Device ID of the partition.

Legal Values

String of up to 4 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.PortGuid[Partition:n] (Read Only)

Description

The permanent Port GUID assigned to the partition (PF) during manufacturing used when more than one PF is assigned to the port. The permanent Port GUID assigned to the partition during manufacturing.

Legal Values

String of ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.PortNumber[Partition:n] (Read Only)

Description

Port that the partition belongs to. Replace n with the number of the partition. Port that the partition belongs to. Replace n with the number of the partition.

Legal Values

Integer values.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.RDMANICModeOnPartition (Read or Write)

Description

Enable/Disable the NIC + RDMA personality on the partition. This setting is for when operating in NPar mode only. Replace n with the number of the partition. Note: This personality type may be specified as the partition default if RDMA traffic can be supported irrespective of any other device setting. Specify use of the partition for both L2-Ethernet and RDMA traffic. [Vendor may want to customize type of RDMA supported].

Legal Values

Enabled
Disabled

Default Value

Varies

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.RDMANICModeOnPartition[Partition:n] (Read or Write)

Description

Legal Values

Enabled
Disabled

Default Value

Varies

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.SVLanId[Partition:n] (Read or Write)

Description

Specify the value of the S-VLAN ID to be used by the partition for all traffic when operating in the Advanced NPar mode. The S-VLAN ID must be unique per partition and in the range from 3 to 4094. NOTE : This attribute shall only be implemented when Advanced NPar is supported. Specify the S-VLAN ID to be used by the partition in Advanced NPar mode. The S-VLAN ID must be unique per partition and in the range from 3 to 4094. Default value will be partition number + 2

Legal Values

Integer values from 3 to 4094.

Default Value

Partition number + 2

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtFIPMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable FIP-MAC address for FCoE. Virtual addresses written will also generate corresponding VWWNN and VWWPN addresses as defined in Y741D. Replace n with the number of the partition. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Programmatically assignable FIP-MAC address for the FCoE partition.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtIscsiFIPMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable combination iSCSI Offload and FIP-MAC address for FCoE. Virtual addresses written will also generate corresponding VWWNN and VWWPN addresses as defined in Y741D. Replace n with the number of the partition. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Programmatically assignable combination MAC address for iSCSI Offload and FCoE FIP.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtIscsiMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable MAC address for iSCSI offload. Programmatic write for support of I/O Identity feature. Replace n with the number of the partition. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Programmatically assignable MAC address for the iSCSI offload partition.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtL2FIPMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable combination FIP-MAC address for FCoE. Virtual addresses written will also generate corresponding VWWNN and VWWPN addresses as defined in Y741D. Replace n with the number of the partition. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Programmatically assignable combination MAC address for Ethernet and FCoE FIP.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtL2IscsiFIPMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable combination Ethernet, iSCSI Offload and FIP-MAC address for FCoE. Virtual addresses written will also generate corresponding VWWNN and VWWPN addresses as defined in Y741D. Replace n with the number of the partition. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Programmatically assignable combination MAC address for Ethernet, iSCSI Offload and FCoE FIP.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtL2IscsiMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable combination MAC address for Ethernet and iSCSI offload. Programmatic write for support of I/O Identity feature. Replace n with the number of the partition. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Programmatically assignable combination MAC address for Ethernet and iSCSI Offload.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable MAC address. Programmatic write for support of I/O Identity feature. Replace n with the number of the partition. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature and partition enablement. Programmatically assignable MAC address for partition.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtNodeGuid[Partition:n] (Read or Write)

Description

Programmatically assignable partition Node GUID address used when more than one PF is assigned to the port. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent partition Node GUID address is by writing 0s to the virtual partition Node GUID. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. Programmatically assignable Node GUID address of the partition.

Legal Values

String of up to 19 ASCII characters.

Default Value

0000:0000:0000:0000

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtNvmeTcpMacAddr[Partition:n] (Read or Write)

Description

Programmatically assignable MAC address for NVMe/TCP offload. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address should be readable at all times, irrespective of feature enablement. Programmatically assignable MAC address for the NVMe/TCP offload partition.

Legal Values

String of up to 17 ASCII characters.

Default Value

00:00:00:00:00:00

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtPortGuid[Partition:n] (Read or Write)

Description

Programmatically assignable partition Port GUID address used when more than one PF is assigned to the port. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent partition GUID address is by writing 0s to the virtual partition GUID. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. Programmatically assignable Port GUID address of the partition.

Legal Values

String of up to 19 ASCII characters.

Default Value

0000:0000:0000:0000

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtWWN[Partition:n] (Read or Write)

Description

Programmatically assignable Fibre Channel World Wide Node Name identifier for FCoE. Virtual addresses written will also be modified by subsequent writes to the VirtFIP-MAC addesss as defined in Y741D. Replace n with the number of the partition. The supported method of clearing this virtual address is by writing 0s as the address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. . Programmatically assignable Fibre Channel World Wide Node Name identifier for partition FCoE.

Legal Values

String of up to 23 ASCII characters.

Default Value

00:00:00:00:00:00:00:00

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.VirtWWPN[Partition:n] (Read or Write)

Description

Programmatically assignable Fibre Channel World Wide Port Name identifier for FCoE. Virtual addresses written will also be modified by subsequent writes to the VirtFIP-MAC addesss as defined in Y741D. Replace n with the number of the partition. The supported method of clearing this virtual address is by writing 0s as the address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. Programmatically assignable Fibre Channel World Wide Port Name identifier for partition FCoE.

Legal Values

String of up to 23 ASCII characters.

Default Value

00:00:00:00:00:00:00:00

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.WWN[Partition:n] (Read Only)

Description

Fibre Channel World Wide Node Name identifier for FCoE. Replace n with the number of the partition. Fibre Channel World Wide Node Name identifier for FCoE. Replace n with the number of the partition.

Legal Values

String of up to 23 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.WWPN[Partition:n] (Read Only)

Description

Fibre Channel World Wide Port Name identifier for FCoE assigned during manufacturing. Replace n with the number of the partition. Fibre Channel World Wide Port Name identifier for FCoE assigned during manufacturing. Replace n with the number of the partition.

Legal Values

String of up to 23 ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.ConfigureFormn.iScsiOffloadMode[Partition:n] (Read or Write)

Description

Enable/Disable the iSCSI offload personality on the partition. Replace n with the number of the partition. Specify use of the partition for iSCSI offload storage traffic.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Autocomplete will not work if you replace n with the index in this object. You have to type NIC.ConfigureFormn and press tab to view the list of attributes.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DCBSettings.CongestionNotification (Read Only)

Description: Indicates whether Congestion Notification capability is supported. Indicates whether Congestion Notification capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DCBSettings.EnhancedTransmissionSelection (Read Only)

Description: Indicates whether Enhanced Transmission Selection capability is supported. Indicates whether Enhanced Transmission Selection capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DCBSettings.PriorityFlowControl (Read Only)

Description: Indicates whether the Priority Flow Control capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.AdvNParSupport (Read Only)

Description

Indicates whether Advanced NPar S-Tag functionality is supported. Indicates whether Advanced NPar S-Tag functionality is supported.

Legal Values

String of ASCII characters.

Default Value

N/A

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.EVBModesSupport (Read Only)

Description

Indicates the type of EVB Modes supported. Indicates the type of EVB Modes supported.

Legal Values

String of ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.NParEP (Read or Write)

Description

Controls enablement of NParEP mode in which more than 8 PCI Physical Functions are exposed by the device. When disabled, the device must expose only a maximum of 8 PFs in the traditional PCI B:D:F addressing mode, regardless of any ARI capability being advertised for SR-IOV support. [Not to be implemented if not supported] Note: Not all PCI slots in all servers are capable of supporting virtualization features based on ARI and SR-IOV. The controller should check PCI config space settings to ensure that vitualization modes are available before allowing their selection by the user. NParEP mode enables more than 8 partitions on the device. It must not be enabled if the system and OS do not support devices with more than 8 PCI Physical Functions.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.NumPorts (Read or Write)

Description

Configuration control for Controllers that have the ability to support different port counts per SFF (e.g., SFP-DD, QSFP) or backplane interface. Controllers on implementations that are fixed in their number of ports shall not implement this attribute. This attribute is defined as device-level due to symmetry expectations, if symmetry is not a requirement, it should be implemented at the port level. Specify the total number of ports to be configured on the physical interfaces. [VENDOR to modify appropriately]

Legal Values

Default Value

varies

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.NumberVFSupported (Read Only)

Description

The total number of PCI Virtual Functions supported on this port (or device). Whether the number applies to the device as a whole, or to an individual port, is indicated by the value of the Virtual Function Allocation Basis. The number of virtual functions supported on this port (or device) [VENDOR modify appropriately for the implementation].

Legal Values

Integer values from 0 to 256.

Default Value

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.PTMSupport (Read Only)

Description

Indicates whether the controller and the overall implementation supports Precision Time Management as defined by the PCI SIG. Indicates whether the controller as implemented supports Precision Time Management

Legal Values

String of ASCII characters.

Default Value

N/A

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.PartitionStateInterpretation (Read Only)

Description

Describes how partitioning is implemented and how the PartitionState attribute is used in the controller. A value of Fixed signifies that partition states are locked and that the current values of PartitionState[n] will not change. A value of Variable signifies that PartitionState[n] may/will change values during the course of device operation as a result of user configuration. Implementations that support changes in PartitionState must implement this attribute. The Default value is implementation dependent. Describes how partitioning is implemented and how the PartitionState attribute is used in the controller.

Legal Values

Fixed
Variable

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.RDMAApplicationProfile (Read or Write)

Description

Indicates what RDMA configuration profiles are supported by the controller. [Vendor input requested if 1) additional profiles are thought to be needed, 2) if the appl profile can vary by port or partitionm and 3) if appl profiles are supported on a partition basis]. Note: RoCE 1 and RoCE 2 are vendor-specific profiles and should not be interpreted as a version of RoCE. Specify the RDMA application profile setting to use in operation. [Vendor to clarify availability and usage].

Legal Values

Storage
HPCC
RoCE 1
RoCE 2

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.RDMAProtocolSupport (Read Only)

Description

Indicates what RDMA protocol support is enabled by the controller. Implement as ReadOnly and browser suppressed if the controller only supports one type of RDMA; R/W and not browser suppressed if multiple settings are supported and selectable. [Vendor to provide default setting information] Specify what RDMA Protocol is to be used in operation. [Vendor modify as appropriate].

Legal Values

iWARP
RoCE
iWARP + RoCE

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.RDMASupport (Read Only)

Description

Capability indicator for controllers supporting Remote Direct Memory Management (RDMA), the remote memory management capability that allows server to server data movement directly between application memory without any CPU involvement. Indicates whether any RDMA protocol is supported by the controller.

Legal Values

String of ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.SRIOVSupport (Read Only)

Description

Indicates whether SR-IOV capability is supported Indicates whether SR-IOV capability is supported.

Legal Values

String of ASCII characters.

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.STagEtherType (Read or Write)

Description

Specifies the EtherType to be used by all partitions on the port when Advanced NPar S-tagging is enabled in the Virtualization Mode setting. NOTE: This attribute shall only be implemented when Advanced NPar is supported. Specify the EtherType to be used when using Advanced NPar S-tagging.

Legal Values

0x88a8
0x9100

Default Value

0x88a8

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.VFAllocBasis (Read Only)

Description

Defines the domain in which Virtual Functions are allocated; either Port or Device. Note: A device which implements less than 1 PF per physical port must use Device level VF allocation. Defines the domain in which Virtual Functions are allocated.

Legal Values

Port
Device

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.VFAllocMult (Read Only)

Description

Defines the multiple (e.g. x1, x4, x8, etc.) in which VFs must be allocated to a PF. [VENDOR provide appropriate help text for the implementation - what is allowed, etc].

Legal Values

Integer values from 1 to 255.

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.DeviceLevelConfig.VirtualizationMode (Read or Write)

Description

The Virtualization Mode setting for the device. Note: Not all PCI slots in all servers are capable of supporting virtualization features based on ARI and SR-IOV. The implementation shall check the state of the ARI forwarding bit in the immediate upstream PCI ports config space settings (Device Control Register 2, bit 5) to ensure that it is set before before allowing the selection of SR-IOV and NParEP by the user, if not, those selections shall be disallowed. Specify the type of virtualization used by the controller on all ports.

Legal Values

None
NPar
SR-IOV
NPar + SR-IOV
Advanced NPar
Advanced NPar + SR-IOV

Default Value

NONE

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

To get the actual supported values for BIOS, NIC, and FC components, query the help with an index. If you query without an index, the generic help is displayed.

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.AddressingMode (Read Only)

Description: Addressing Mode utilized for FCoE transactions Specify whether SPMA or FPMA addressing will be used for FCoE transactions.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MTUReconfigurationSupport (Read Only)

Description: Indicates whether the MTU Reconfiguration capability is supported. Indicates whether the MTU Reconfiguration capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MaxFrameSize (Read Only)

Description: The maximum frame size of each FCoE frame. Maximum frame size of each FCoE frame.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MaxIOsPerSession (Read Only)

Description: The maximum number of IOs supported per session. Maximum number of IOs supported per session.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MaxNPIVPerPort (Read Only)

Description: The maximum number of NPIV WWNs per port. Maximum number of NPIV WWNs per port.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MaxNumberExchanges (Read Only)

Description: The maximum number of exchanges supported. Maximum number of exchanges supported.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MaxNumberLogins (Read Only)

Description: The maximum number of logins supported per port. Maximum number of logins supported per port.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MaxNumberOfFCTargets (Read Only)

Description: The maximum number of FC targets supported. Maximum number of FC targets supported.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCOECapabilities.MaxNumberOutStandingCommands (Read Only)

Description: The maximum number of outstanding commands supported across all sessions. Maximum number of outstanding commands supported across all sessions.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.BootOrderFirstFCoETarget (Read or Write)

Description: Setting to specify whether and in what order a boot from the ports first defined target is attempted. The current implementation allows for four potential boot targets to be defined per FCoE boot-capable port. Each target carries a boot order attribute. From all of the targets defined in all the vendors FCoE boot ports in the system, the user may select a maximum of four targets to attempt to boot from, assigning a boot order value from one to four (first to last). Targets not selected must be given a value of 0. The settings of one to four must be unique in the system; there must be no duplication of the values one to four in either the same port or in different ports across the system. The driver will enforce this requirement (a target previously assigned a boot order value of x is set to 0 when a new target is assigned a value of x). Specify this ports place in the FCoE boot order 1-4 or 0=disabled.
Legal Values: Integer values.
Default Value: 0
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.BootOrderFourthFCoETarget (Read or Write)

Description: Setting to specify whether and in what order a boot from the ports fourth defined target is attempted. Specify this ports place in the FCoE boot order 1-4 or 0=disabled.
Legal Values: Integer values.
Default Value: 0
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.BootOrderSecondFCoETarget (Read or Write)

Description: Setting to specify whether and in what order a boot from the ports second defined target is attempted. Specify this ports place in the FCoE boot order 1-4 or 0=disabled.
Legal Values: Integer values.
Default Value: 0
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.BootOrderThirdFCoETarget (Read or Write)

Description: Setting to specify whether and in what order a boot from the ports third defined target is attempted. Specify this ports place in the FCoE boot order 1-4 or 0=disabled.
Legal Values: Integer values.
Default Value: 0
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.ConnectFirstFCoETarget (Read or Write)

Description

Setting to enable whether first target connection is attempted. Specify whether the FCoE initiator is to connect to the first FCoE storage target.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.FirstFCoEBootTargetLUN (Read or Write)

Description: LUN of the first FCoE storage target that the FCoE initiator will boot the system from when the Connect attribute is enabled. Specify the boot Logical Unit Number (LUN) of the first FCoE storage target that will be used by the FCoE initiator.
Legal Values: Integer values from 0 to 18446744073709551615.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.FirstFCoEFCFVLANID (Read or Write)

Description: Attribute for configuring the VLAN ID to be used to connect to the first FC storage target. Specify the VLAN ID to be used in connecting to the first FC storage target.
Legal Values: Integer values from 1 to 4094.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.FirstFCoEWWPNTarget (Read or Write)

Description: World Wide Port Name of the first FCoE storage target. Note: At present, the Dell FCoE information model only defines one storage target. Specify the World Wide Port Name (WWPN) of the first FCoE storage target.
Legal Values: String of up to 23 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEConfiguration.MTUParams (Read or Write)

Description

Configure scoping of the MTU setting. Specify the scope of the MTU (Maximum Transmission Unit) parameter.

Legal Values

Global
Per DCB Priority
Per VLAN

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEGenParams.FCoEBootScanSelection (Read or Write)

Description

Configuration of the ports behavior in booting the system from FC Target(s). Only behaviors supported by the option-ROM need to be implemented. In the following cases, no fabric discovery shall be attempted: Disabled - Initiator does not attempt to boot. Specified LUN - Initiator attempts to boot to the specified World Wide Port Name and LUN for 1st target, if that fails then a boot using the 2nd target parameters shall be attempted. In the following cases, fabric discovery shall be attempted and the resulting discovered targets will be put in a list sorted by the reported FC destination ID. This list will be checked in order until the selected LUN policy is met: First LUN - attempt boot from the first bootable LUN of the targets discovered by adapter. First LUN 0 - attempt boot from the first bootable LUN 0 of the targets discovered by adapter. First LUN Not LUN 0 - attempt boot from the first bootable LUN that is not LUN 0 of the targets discovered by adapter. Fabric Discovered LUN - attempt boot based on the LUN assignment provided by management infrastructure in the fabric. Specify the FCoE initiator behavior for booting the system from specified Fibre Channel boot target(s) or fabric discovered target(s).

Legal Values

Disabled
First LUN
First LUN 0
First LUN Not LUN 0
Fabric Discovered LUN
Specified LUN

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEGenParams.FCoEFabricDiscoveryRetryCnt (Read or Write)

Description: Retry count for FCoE fabric discovery. Specify the retry count for FCoE fabric discovery.
Legal Values: Integer values from 0 to 60.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEGenParams.FCoEFirstHddTarget (Read or Write)

Description

Specifies whether the FCoE target is represented as the first HDD to the system. Specify whether the FCoE target is represented as the first HDD to the system.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEGenParams.FCoELnkUpDelayTime (Read or Write)

Description: Controls how long the FCoE initiator waits, in seconds, after an Ethernet link is established before sending any data over the network Specify how long the FCoE Initiator waits after an Ethernet link is established before sending any data over the network. Units are in seconds.
Legal Values: Integer values from 0 to 255.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEGenParams.FCoELunBusyRetryCnt (Read or Write)

Description: Controls the number of connection retries the FCoE boot initiator will attempt if the FCoE target LUN is busy. Specify the number of connection retries the FCoE boot initiator will attempt if the FCoE target LUN is busy.
Legal Values: Integer values from 0 to 60.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FCoEGenParams.FCoETgtBoot (Read or Write)

Description

Attribute for setting whether system boot to the FCoE target is attempted. Enables the FCoE initiator to boot the system to the FCoE target. One Time Disabled disables FCoE boot for the next (current) boot, after which it is enabled.

Legal Values

Enabled
Disabled
One Time Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FrmwImgMenu.ControllerBIOSVersion (Read Only)

Description: Controller BIOS version information Installed device BIOS version information.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FrmwImgMenu.EFIVersion (Read Only)

Description: EFI device driver version information. Installed device EFI driver version information.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.FrmwImgMenu.FamilyVersion (Read Only)

Description: Firmware family version information. Same as what is returned in the PackageVersionName field by the Firmware Management Protocol GetPackageInfo() call. Installed device firmware family version information.
Legal Values: String of up to 11 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.GlobalBandwidthAllocation.MaxBandwidth[Partition:n] (Read or Write)

Description: The maximum percentage of port TX bandwidth allocated to the partition. Oversubscription is allowed. Specified on a per partition basis. Replace n with the number of the partition. Maximum Bandwidth represents the maximum transmit bandwidth of the partition as a percentage of the full physical port link speed. The Maximum Bandwidth range is 0-100 percent for each enabled partition.
Legal Values: Integer values from 0 to 100.
Default Value: 100
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.GlobalBandwidthAllocation.MinBandwidth[Partition:n] (Read or Write)

Description: The minimum percentage of port TX bandwidth allocated to the partition. Alternatively, this value represents a relative bandwidth weighting of partition traffic to other partitions. Specified on a per partition basis. Replace n with the number of the partition. [Vendor: modify as appropriate.] Minimum Bandwidth represents the minimum transmit bandwidth of the partition as a percentage of the full physical port link speed. The Minimum Bandwidth range is 0-100 percent for each enabled partition.
Legal Values: Integer values from 0 to 100.
Default Value: 0
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.ConnectFirstTgt (Read or Write)

Description

Setting to enable whether connection to the first target is attempted. Enable connecting to the first iSCSI target.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.FirstTgtBootLun (Read or Write)

Description: Specifies the first iSCSI target boot LUN. Specify the boot Logical Unit Number (LUN) on the first iSCSI storage target.
Legal Values: Integer values from 0 to 18446744073709551615.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.FirstTgtChapId (Read or Write)

Description: First Target CHAP ID (up to 128 characters in length). If only a single value of CHAP ID supported then it is stored here. Specify the first iSCSI storage target Challenge-Handshake Authentication Protocol (CHAP) ID. [vendor to specify what is allowed].
Legal Values: String of up to 128 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.FirstTgtChapPwd (Read or Write)

Description: First Target CHAP Secret ( 0 or 12 to 16 characters in length). If only a single value of CHAP Secret is supported then it is stored here. Specify the Challenge-Handshake Authentication Protocol secret (CHAP password) of the first iSCSI storage target. [Vendor to specify what is allowed].
Legal Values: String of up to 16 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.FirstTgtIpAddress (Read or Write)

Description: First iSCSI target IP address. Will be either IPv4 or IPv6 format depending on the value of the FirstTgtIpVer attribute. Specify the IP address of the first iSCSI target.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.FirstTgtIpVer (Read or Write)

Description

Setting displays and allows configuration of IP version used for first iSCSI target when iSCSIDualIPVersionSupport is available. Specify whether IPv4 or IPv4 network addressing will be used for first iSCSI target.

Legal Values

IPv4
IPv6

Default Value

IPv4

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.FirstTgtIscsiName (Read or Write)

Description: The iSCSI Qualified Name (IQN) of the first target. Specify the iSCSI Qualified Name (IQN) of the first iSCSI storage target.
Legal Values: String of up to 223 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiFirstTgtParams.FirstTgtTcpPort (Read or Write)

Description: TCP Port number of the first iSCSI target. Specify the TCP Port number of the first iSCSI target.
Legal Values: Integer values from 1 to 65535.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.ChapAuthEnable (Read or Write)

Description

Setting to enable CHAP Authentication for iSCSI initiator. Enable the ability of the initiator to use CHAP authentication when connecting to the iSCSI target.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.ChapMutualAuth (Read or Write)

Description

Setting to enable mutual CHAP authentication between the iSCSI initiator and target. To use mutual CHAP authentication, specify an initiator secret on the Initiator Parameters page and configure that secret on the target.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.DhcpVendId (Read or Write)

Description: Vendor ID as presented to DHCP service. Control what Vendor ID is presented to the DHCP service.
Legal Values: String of up to 255 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.FirstHddTarget (Read or Write)

Description

Enable/Disable the target appearing as the first hard disk drive (HDD) in the system when iSCSI booting. Specify whether the iSCSI target appears as the first hard disk drive (HDD) in the system.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.IpAutoConfig (Read or Write)

Description

Setting to enable acquisition of IPv6 TCP/IP parameters from DHCP. This option is specific to IPv6. Controls the source of the initiator IP address, DHCP or static assignment.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.IpVer (Read or Write)

Description

Setting displays and allows configuration of the IP version used by iSCSI initiator and targets (Initiator only when a seperate target ipver is implemented). If only one IP version is supported, this attribute should be set to that version and be made Read Only. Specify whether IPv4 or IPv6 network addressing will be used for iSCSI initiator and targets (Applies to the Initiator only when a seperate target IP Version is implemented). [Vendor to provide implementation-specific language].

Legal Values

IPv4
IPv6
None

Default Value

IPv4

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.IscsiTgtBoot (Read or Write)

Description

Boot to iSCSI target after connection. Specify whether the iSCSI initiator will boot to the specified iSCSI target after connection. One Time Disabled disables iSCSI boot for the next (current) boot, after which it is enabled.

Legal Values

Enabled
Disabled
One Time Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.IscsiVLanId (Read or Write)

Description: VLAN ID used for iSCSI boot. Specify the VLAN ID to be used for iSCSI boot mode. The VLAN ID must be in the range from 1 to 4094. [Vendor confirm support for this range].
Legal Values: Integer values from 1 to 4094.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.IscsiVLanMode (Read or Write)

Description

Enable/Disable Virtual LAN mode for iSCSI boot. Specify use of a VLAN tag to be used by iSCSI boot.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.IscsiViaDHCP (Read or Write)

Description

Setting to enable acquisition of iSCSI target parameters from DHCP. Enables the acquisition of iSCSI target parameters from DHCP.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.LnkUpDelayTime (Read or Write)

Description: The time to wait for the link to establish before driver initialization. Specifies how long the iSCSI boot host software should wait, in seconds, after an Ethernet link is established before sending any data over the network.
Legal Values: Integer values from 0 to 255.
Default Value: 0
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.LunBusyRetryCnt (Read or Write)

Description: Controls the retry count for target. Specify the number of connection attempts the iSCSI boot initiator will attempt if the iSCSI target LUN is busy.
Legal Values: Integer values from 0 to 60.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.TcpIpViaDHCP (Read or Write)

Description

Setting to enable acquisition of IPv4 TCP/IP parameters from DHCP This option is specific to IPv4. Controls the source of the initiator IP address, DHCP or static assignment.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.TcpTimestmp (Read or Write)

Description

Enable/Disable use of TCP timestamps in network packets Specify use of TCP timestamps in network packets, as defined in RFC 1323.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiGenParams.WinHbaBootMode (Read or Write)

Description

Controls if adapter boots as an iSCSI Offload HBA or uses software initiator mode Enable iSCSI Offload HBA boot mode and disables iSCSI software initiator boot mode.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorChapId (Read or Write)

Description: Initiator CHAP ID (up to 128 characters in length). If this can be set on a per target basis, then the first target value shall be stored here. Specify the iSCSI initiator Challenge-Handshake Authentication Protocol (CHAP) ID. [Vendor to describe what is allowed].
Legal Values: String of up to 128 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorChapPwd (Read or Write)

Description: iSCSI initiator CHAP secret (0 or 12 to 16 characters in length). If this can be set on a per target basis, then the value for the first target shall be stored here. Specify the iSCSI initiator Challenge-Handshake Authentication Protocol (CHAP) secret (password). [Vendor to describe what is allowed].
Legal Values: String of up to 16 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorGateway (Read or Write)

Description: iSCSI initiator default Gateway IP address. Will be in either IPv4 or IPv6 format depending on the value of the IpVer attribute. Specify the IP address of the default Gateway used by the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpAddr (Read or Write)

Description: The iSCSI initiator IP address. Will be either in IPv4 or IPv6 format depending on value of the IpVer attribute. Specify the IP address of the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv4Addr (Read or Write)

Description: The iSCSI initiator IP address in IPv4 format when iSCSIDualIPVersionSupport is available. Specify the IPv4 address of the iSCSI initiator.
Legal Values: String of up to 15 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv4Gateway (Read or Write)

Description: The iSCSI initiator default Gateway IP address in IPv4 format when iSCSIDualIPVersionSupport is available. Specify the IPv4 IP address of the default Gateway used by the iSCSI initiator.
Legal Values: String of up to 15 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv4PrimDns (Read or Write)

Description: iSCSI initiator Primary DNS IP Address in IPv4 format when iSCSIDualIPVersionSupport is Available. Specify the IPv4 IP address of the Primary DNS used by the iSCSI initiator.
Legal Values: String of up to 15 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv4SecDns (Read or Write)

Description: iSCSI initiator Secondary DNS IP address in IPv4 format when iSCSIDualIPVersionSupport is Available. Specify the IPv4 IP address of the Secondary DNS used by the iSCSI initiator.
Legal Values: String of up to 15 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv6Addr (Read or Write)

Description: The iSCSI initiator IP address in IPv6 format when iSCSIDualIPVersionSupport is available. Specify the IPv6 IP address of the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv6Gateway (Read or Write)

Description: The iSCSI initiator default Gateway IP address in IPv6 format when iSCSIDualIPVersionSupport is available. Specify the IPv6 IP address of the default Gateway used by the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv6PrimDns (Read or Write)

Description: The iSCSI initiator Primary DNS IP Address in IPv6 format when iSCSIDualIPVersionSupport is Available. Specify the IPv6 IP address of the Primary DNS used by the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorIpv6SecDns (Read or Write)

Description: The iSCSI initiator Secondary DNS IP address in IPv6 format when iSCSIDualIPVersionSupport is Available. Specify the IPv6 IP address of the Secondary DNS used by the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorName (Read or Write)

Description: Setting to represent and set the iSCSI initiator iSCSI Qualified Name (IQN). Specify the initiators iSCSI Qualified Name (IQN).
Legal Values: String of up to 223 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorPrimDns (Read or Write)

Description: The iSCSI initiator Primary DNS IP Address. Will be in either IPv4 or IPv6 format depending on the value of the IpVer attribute. Specify the Primary DNS IP address used by the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorSecDns (Read or Write)

Description: The iSCSI initiator Secondary DNS IP address. Will be in either IPv4 or IPv6 format depending on the value of the IpVer attribute. Specify the Secondary DNS IP address used by the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorSubnet (Read or Write)

Description: The iSCSI initiator Subnet Mask for an IPv4 initiator configuration. Specify the IPv4 Subnet Mask of the iSCSI initiator.
Legal Values: String of up to 15 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiInitiatorParams.IscsiInitiatorSubnetPrefix (Read or Write)

Description: The iSCSI initiator Subnet Mask Prefix for an IPv6 initiator configuration. Specify the IPv6 Subnet Mask Prefix of the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.ConnectSecondTgt (Read or Write)

Description

Setting to enable whether connection to the second target is attempted. Enable connecting to the second iSCSI target.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.SecondTgtBootLun (Read or Write)

Description: Specifies the second iSCSI target boot LUN. Specify the boot Logical Unit Number (LUN) on the second iSCSI storage target.
Legal Values: Integer values from 0 to 18446744073709551615.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.SecondTgtChapId (Read or Write)

Description: Second Target CHAP ID (up to 128 characters in length). If only a single value of CHAP ID supported for all targets then it is stored here Specify the Challenge-Handshake Authentication Protocol (CHAP) ID of the second iSCSI storage target. [Vendor to specify what is allowed].
Legal Values: String of up to 128 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.SecondTgtChapPwd (Read or Write)

Description: Second Target CHAP Secret (0 or 12 to 16 characters in length). If only a single value of CHAP Secret is supported then it is stored here Specify the Challenge-Handshake Authentication Protocol (CHAP) secret (target CHAP password) of the second iSCSI storage target. [Vendor to specify what is allowed].
Legal Values: String of up to 16 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.SecondTgtIpAddress (Read or Write)

Description: Second iSCSI target IP address. Will be either IPv4 or IPv6 format depending on the value of the SecondTgtIpVer attribute Specify the IP address of the second iSCSI target.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.SecondTgtIpVer (Read or Write)

Description

Setting displays and allows configuration of IP version used for second iSCSI target when iSCSIDualIPVersionSupport is available Specify whether IPv4 or IPv4 network addressing will be used for the second iSCSI target.

Legal Values

IPv4
IPv6

Default Value

IPv4

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.SecondTgtIscsiName (Read or Write)

Description: The iSCSI Qualified Name (IQN) of the second target Specify the iSCSI Qualified Name (IQN) of the second iSCSI storage target.
Legal Values: String of up to 223 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondTgtParams.SecondTgtTcpPort (Read or Write)

Description: TCP Port number of second iSCSI target Specify the TCP Port number of the second iSCSI target.
Legal Values: Integer values from 1 to 65535.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondaryDeviceParams.SecondaryDeviceMacAddr (Read or Write)

Description: MAC address of the secondary iSCSI boot adapter. Specify the MAC address of a secondary iSCSI boot adapter for redundancy in case of a boot failure.
Legal Values: String of up to 17 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondaryDeviceParams.UseIndTgtName (Read or Write)

Description

Use Independent Target Name when multipath I/O is enabled Specify whether to use Independent Target Name when MPIO is enabled.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.IscsiSecondaryDeviceParams.UseIndTgtPortal (Read or Write)

Description

Setting to use independent target portal when multipath I/O is enabled Specify whether to use Independent Target Portal (Enable when using MPIO mode).

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.100Gbps1 (Read or Write)

Description

Speed selector for the specified link speed to be advertised to the link partner for boot protocol operations and possibly including Wake On LAN and shared LOM management features if separate Vaux link speed control is not supported. This setting is only valid when LnkSpeedMethod is set to Manual and should be greyed out when set to Auto. Note: The speed selection shall only be included if it is supported in the implementation. Advertise 100 Gbps (1 lane of 100 Gb)

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.100Gbps2 (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.100Gbps4 (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.100Mbps (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.10Gbps (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.10Mbps (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.1Gbps (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.200Gbps1 (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.200Gbps2 (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.200Gbps4 (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.25Gbps (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.40Gbps (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.50Gbps1 (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.LnkSpeedConfig.50Gbps2 (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.BannerMessageTimeout (Read or Write)

Description: Timeout in seconds for banner display during POST Specify the number of seconds that the OptionROM banner is displayed during POST.
Legal Values: Integer values from 0 to 14.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.BootOptionROM (Read or Write)

Description

This attribute provides enable/disable functionality to the boot entry point (i.e. undi_init) of the legacy Option ROM of the port, effectively controlling the ability to legacy boot via PXE, iSCSI or FCoE. The Option ROM is still required to advertise itself to BIOS and to expose other entry points (such as CLP and UEFI) for configuration purposes if this control is set to disabled. This control must be prohibited from being set to Disabled if the Legacy Boot Protocol attribute is set to anything but None. Controls the enablement of legacy Boot Protocols in the Option ROM.

Legal Values

Enabled
Disabled

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.BootRetryCnt (Read or Write)

Description

Configure the number of retries in case of boot failure. Specify the number of retries to attempt in case of a boot failure.

Legal Values

No Retry
1 Retry
2 Retries
3 Retries
4 Retries
5 Retries
6 Retries
Indefinite Retries

Default Value

NoRetry

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.BootStrapType (Read or Write)

Description

Configure the boot strap mechanism used to boot to the OS. Specify the boot strap method used to boot to the operating system.

Legal Values

Auto Detect
BBS
Int 18h
Int 19h

Default Value

AutoDetect

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.FWBootProtocol (Read or Write)

Description

Selection of the boot protocol for the CNA port when the boot process is local to the controller. Select the boot protocol to be used for boot operations handled by the adapter. Legacy PXE must be selected when the System Boot Mode is set to Legacy.

Legal Values

Legacy PXE
UEFI iSCSI HBA
UEFI FCoE
None

Default Value

varies

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.HideSetupPrompt (Read or Write)

Description

Enable/Disable the option ROM setup prompt (banner) during POST. Specify whether to display or hide the legacy Option ROM setup prompt during system Power On Self Test (POST).

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.LegacyBootProto (Read or Write)

Description

Selection of the boot protocol for the port to use in legacy BIOS (non-UEFI) boot mode. The default value of the setting varies by implementation and is defined in ENG0012856. Select a boot protocol to be used in legacy BIOS (non-UEFI) boot mode.

Legal Values

PXE
iSCSI
FCoE
None
iSCSI Primary
iSCSI Secondary
iPXE without failover
iSCSI without failover

Default Value

varies

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.LnkSpeed (Read or Write)

Description

Selector for link speed(s) to be advertised to link partner for boot operations.  Implementations should only include supported link speeds.  Existing implementations may remain unchanged, new implementations should not use those speeds listed as deprecated but use the new speeds that have been added that infer what modulation scheme is in use, NRZ or PAM4.  New implementations should transition to allow multiple speeds to be selected instead of just one in a simple enumeration scheme. Specifies the port link speed to be used when booting the selected protocol.

Legal Values

Auto Negotiated
10 Mbps Half
10 Mbps Full
100 Mbps Half
100 Mbps Full
1 Gbps
10 Gbps
25 Gbps
40 Gbps
50 Gbps (2x25)
50 Gbps (1x50)
100 Gbps (4x25)
100 Gbps (2x50)
100 Gbps (1x100)
200 Gbps (4x50)
200 Gbps (2x100)
200 Gbps (1x200)

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.LnkSpeedMethod (Read or Write)

Description

Replacement for the previously defined LinkSpeed attribute to be used (at least) for those controllers that support speeds above 25 Gbps. This attribute allows the user to select between auto and manual modes of configuring what the port advertises for link negotiation. Select how to choose which port link parameters to advertise for system boot operation, automatically or by user selection. [VENDOR: modify to suit your implementation]

Legal Values

Auto
Manual

Default Value

Auto

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.NumberVFAdvertised (Read or Write)

Description: This value is the number of PCI Virtual Functions Advertised by the port (function) in PCI config space when SR-IOV is enabled in non-NPar mode. Specify the number of PCI Virtual Functions (VFs) to be advertised on this port in non-NPAR mode.
Legal Values: Integer values from 0 to 256.
Default Value: 0
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.PermitTotalPortShutdown (Read or Write)

Description

When implemented and enabled, any port down command from the host OS or driver will cause the network port to completely shut down and cease all operations including support of WoL and NC-SI Pass-through.  Shutdown is defined as no electrical activity (e.g., PHY disabled) and no LED activity.  It does not imply or require any physical or electrical isolation.  Not intended for implementation or use on backplane designs. External network traffic to and from any VF instantiated on any PF on the shut down port is similarly shut down. Maintaining traffic flow between internal functions when the port is shutdown is implementation dependent. Specifies whether or not to allow the port to be completely disabled when a Port Down command is received from the Host OS or driver. NOTE: Use with caution, port shutdown will halt all operations configured on the port including WakeOnLAN and shared LOM. [VENDOR: modify to include any corner cases of the implementation]

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.VLanId (Read or Write)

Description: Specifies the VLAN tag to be used with the selected boot protocol. Specify the VLAN tag to be used with the selected boot protocol. The VLAN ID must be in the range from 1 to 4094. [Vendor to provide implementation-specific language].
Legal Values: Integer values from 1 to 4094.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.VLanMode (Read or Write)

Description

Enable/Disable VLAN tagging on the selected boot protocol. Note: The vendor will have to customize help text to define what boot protocols can use VLAN tagging. Virtual LAN mode enables use of a VLAN tag to be used by [vendor specify boot protocols that support VLAN].

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.WakeOnLan (Read or Write)

Description

Enable/Disable Wake On LAN feature Enables the server to be powered on using an in-band magic packet.

Legal Values

Enabled
Disabled

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.WakeOnLanLnkSpeed (Read or Write)

Description

Selector for link speed(s) to be advertised to link partner for Vaux operations including Wake On LAN and shared LOM management features.  Implementations should only include supported link speeds. Existing implementations may remain unchanged, new implementations should not use those speeds listed as deprecated but use the new speeds that have been added that infer what modulation scheme is in use, NRZ or PAM4.  New implementations should transition to allow multiple speeds to be selected instead of just one in a simple enumeration scheme. Select the port speed used for Wake on LAN mode and Vaux Management traffic. [VENDOR to modify appropriately]

Legal Values

Auto Negotiated
10 Mbps Half
10 Mbps Full
100 Mbps Half
100 Mbps Full
1 Gbps
10 Gbps
25 Gbps
40 Gbps
50 Gbps (2x25)
50 Gbps (1x50)
100 Gbps (4x25)
100 Gbps (2x50)
100 Gbps (1x100)
200 Gbps (4x50)
200 Gbps (2x100)
200 Gbps (1x200)

Default Value

AutoNeg

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICConfig.WakeOnLanLnkSpeedMethod (Read or Write)

Description

Replacement for the previously defined WakeOnLanLnkSpeed attribute to be used (at least) for those controllers that support speeds above 25 Gbps. This attribute allows the user to select between auto and manual modes of configuring what the port advertises for link negotiation. Note: If an implementation only supports one pre-OS link speed configuration, this attribute should not be implemented. Select how to choose which port link parameters to advertise for Wake On LAN and shared LOM modes of operation, automatically or by user selection . [VENDOR: modify to suit your implementation]

Legal Values

Auto
Manual

Default Value

Auto

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICPartitioningConfig.FlowControlSetting (Read or Write)

Description

Representation and configuration field for Ethernet Flow Control. Note: This setting only controls the ports Flow Control behavior when in NPar modes of operation, but not when PFC is enabled; The OS driver retains control of Flow Control when NPar is not enabled. Specify the type of Ethernet Flow Control to be used by the port when operating in NPar mode.

Legal Values

Auto
TX:Send Pause on RX Overflow
RX:Throttle TX on Pause Received
TX / RX Flow Control
None

Default Value

Auto

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICPartitioningConfig.NicPartitioning (Read or Write)

Description

Representation and configuration of enablement of partitioning for the device. Note: This attribute is for current HII/UEFI drivers that implement the control ONLY. New HII implementations should only implement the Virtualization Mode attribute. Existing implementations should maintain support for legacy reasons. Enables or disables NIC partitioning for all device ports.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICPartitioningConfig.NumberPCIFunctionsEnabled (Read Only)

Description: The number of PCI Physical Functions currently enabled on this port. The number of PCI Physical Functions currently enabled on this port.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICPartitioningConfig.NumberPCIFunctionsSupported (Read Only)

Description: The number of PCI Physical Functions supported on this port. This value may change depending on the support and configuration of NParEP. The number of PCI Physical Functions supported on this port. This value may change depending on the support and configuration of NParEP.
Legal Values: Integer values.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.NICPartitioningConfig.PartitionState[Partition:n] (Read Only)

Description

Representation of the current enablement state of the partition. There will be an instance of this attribute for each partition. Replace n with the number of the partition. Representation of the current enablement state of the partition.

Legal Values

Enabled
Disabled

Default Value

Enabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.PortLevelConfig.VFDistribution (Read or Write)

Description: The value is a string of numbers, each seperated by a colon that defines the distribution of VFs to PFs within the domain specified by VFAllocBasis. Each number represents the number of PVI Virtual Functions to be advertised in PCI config space by each partition (PF). The numbers must sum to an amount less than or equal to the NumberVFSupported attribute value. A value appears in the colon separated list for each Physical Function that can potentially be present within the allocation domain, independent of its enablement state. Values in the list from left to right apply to function numbers in the domain from least to greatest. Note1: The regex can only perform basic validation of the string format. Note2: Implementers should replace the "*" in the regex with a bound expression that accurately describes the expected string in the context of a given solution (e.g. where NumberVFSupported is 4, the "*" will be replaced with "{3}"). The vendor must provide the appropriate default string for the implementation. Defines the distribution of VFs to PFs within the domain specified by VFAllocBasis. A value appears in the colon separated list for each Physical Function that can potentially be present within the allocation domain. Values in the list from left to right apply to function numbers in the domain from least to greatest. [VENDOR modify appropriately]
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.BlnkLeds (Read or Write)

Description: Blink LEDs for a duration of up to 15 seconds. Only valid for adapters with link LEDs. Specify the number of seconds the LEDs on the physical network port should blink to assist with port identification.
Legal Values: Integer values from 0 to 15.
Default Value: 15
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.BusDeviceFunction (Read Only)

Description: The value of this attribute depends on the state of the NParEP Mode setting. If NParEP Mode is Disabled, the value is the BIOS assigned PCIe Bus:Device:Function identifier. If NParEP Mode is Enabled, the value is the BIOS assigned PCIe Bus:Function identifier. Indicates the PCI Address of the Physical Function assigned to the port.
Legal Values: String of up to 8 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.ChipMdl (Read Only)

Description: This attribute consists of the concatenation of 2 different elements, a vendor-defined silicon marketing name and the silicon revision information as specified in PCI configuration space, separated by space. For example: R720 B0. Specifies the Chip Type.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.DCBXSupport (Read Only)

Description: Indicates whether Data Center Bridging eXchange Protocol (DCBX) is supported. Specify whether Data Center Bridging eXchange Protocol (DCBX) is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.DeviceName (Read Only)

Description: Official product name of the device. Official product name of the device.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.EEEControl (Read or Write)

Description

Enables or Disables the Energy Efficient Ethernet feature on the port if supported by the device. If the scope of the control is not port level, then consultation with Dell is required. The default value of this attribute is specified in the EHRD for the implementation and will not be the same for all adapters. Note: Do not implement if EEE is not supported by the implementation (i.e., the EnergyEfficientEthernet attribute setting). Enables or Disables the Energy Efficient Ethernet feature on the [VENDOR: specify the scope of control, (e.g., port, controller, adapter)]

Legal Values

Maximum Power Savings
Disabled

Default Value

varies

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.EnergyEfficientEthernet (Read Only)

Description: Indicates whether Energy Efficient Ethernet capability is supported. Indicates whether Energy Efficient Ethernet capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.FCoEBootSupport (Read Only)

Description: Indicates whether Fibre Channel over Ethernet Boot capability is supported. Indicates whether Fibre Channel over Ethernet Boot capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.FCoEOffloadMode (Read or Write)

Description

Enable/Disable the FCoE personality on the port. This setting is for when operating in non-NPar mode only. Enables the port for FCoE storage traffic.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.FCoEOffloadSupport (Read Only)

Description: Indicates whether FCoE is supported. Indicates whether FCoE is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.FIPMacAddr (Read Only)

Description: Permanent FIP-MAC address for FCoE assigned during manufacturing. If supported, the current address value should be readable at all times, irrespective of feature enablement. Permanent FIP-MAC address for FCoE assigned during manufacturing.
Legal Values: String of up to 17 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.FeatureLicensingSupport (Read Only)

Description: Indicates whether the Dell Feature Licensing capability is supported. Indicates whether Dell Feature Licensing capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.FlexAddressing (Read Only)

Description: Indicates whether the Dell FlexAddressing feature is supported. Indicates whether the Dell FlexAddressing feature is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.ForwardErrorCorrection (Read or Write)

Description

Type of FEC to use on the link. Shall not be implemented on adapters where it is not appropriate. Specify the type of Forward Error Correction to use on the link (if appropriate)

Legal Values

Auto
Fire Code (Clause 74)
RS-FEC (Clause 91, 108, 134)
Disabled

Default Value

Auto

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.InfiniBand (Read Only)

Description: Indicates whether InfiniBand functionality is supported. Indicates whether InfiniBand functionality is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.IscsiMacAddr (Read Only)

Description: Permanent MAC address for iSCSI offload assigned during manufacturing. If supported, the current address value should be readable at all times, irrespective of feature enablement. Permanent MAC address for iSCSI offload assigned during manufacturing.
Legal Values: String of up to 17 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.LinkStatus (Read Only)

Description

Physical link status of the network port as reported by the controller. Physical link status of the network port as reported by the controller.

Legal Values

Connected
Disconnected

Default Value

None

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.MacAddr (Read Only)

Description: The Permanent MAC address assigned during manufacturing. Permanent MAC address assigned during manufacturing.
Legal Values: String of up to 17 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.MediaDetection (Read or Write)

Description

Optional attribute for those implementations that support the querying of the installed SFF device capabilities to assist in link configuration. How this information is used may differ between implementations. Should not be implemented on adapters where it is not used. Query the installed SFF device capabilities to assist in link configuration [VENDOR to modify appropriately]

Legal Values

Enabled
Disabled

Default Value

varies

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NVMeTCPOffloadSupport (Read Only)

Description: Indicates whether the NVMe/TCP Offload capability is supported. Indicates whether the NVMe/TCP Offload capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NWManagementPassThrough (Read Only)

Description: Indicates whether the Network Management Pass Through capability is supported. Indicates whether the Network Management Pass Through capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NetworkLinkType (Read or Write)

Description

Select the protocol type to be used on a port that supports multiple fabric types. NOTE: Implement ONLY if VPI Mode is supported Select port network protocol (Ethernet/InfiniBand)

Legal Values

Ethernet
InfiniBand

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NicMode (Read or Write)

Description

Enable/Disable the NIC personality on the port. This setting is for when operating in non-NPar mode only. Note: This personality type should be specified as the port default if RDMA is not supported or has dependencies on other device modes or settings. Specify use of the port for L2-Ethernet traffic.

Legal Values

Enabled
Disabled

Default Value

Varies

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NicPartitioningSupport (Read Only)

Description: Indicates whether the NIC Partitioning capability is supported. Indicates whether NIC Partitioning capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NodeGUID (Read Only)

Description: The Permanent Node GUID assigned during manufacturing. Permanent Node GUID assigned during manufacturing.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NvmeTcpBusDeviceFunction (Read Only)

Description: The value of this attribute depends on the state of the NParEP Mode setting. If NParEP Mode is Disabled, the value is the BIOS assigned PCIe Bus:Device:Function identifier of the NVMe/TCP PF . If NParEP Mode is Enabled, the value is the BIOS assigned PCIe Bus:Function identifier of the NVMe/TCP PF . Indicates the PCI Address of the NVMe/TCP Physical Function on the port.
Legal Values: String of up to 8 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NvmeTcpMacAddr (Read Only)

Description: Permanent MAC address for NVMe/TCP Offload operation assigned during manufacturing. If supported, the current address value should be readable at all times, irrespective of feature enablement. Permanent MAC address for NVMe/TCP assigned during manufacturing.
Legal Values: String of up to 17 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NvmeTcpMode (Read or Write)

Description

Enable/Disable the NVMe/TCP personality on the port. This setting is for when operating in non-NPar mode Enables the port for NVMe/TCP storage traffic after boot. If disabled, the user may enable it in the OS, but a reboot is required for activation.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.NvmeTcpPCIDeviceID (Read Only)

Description: PCI Device ID reported by the NVMe/TCP PF when operating in non-NPar mode only. This value is also reported as the Device ID of NVMe/TCP PF at the partition level in NPar modes. PCI Device ID of the NVMe/TCP Physical Function.
Legal Values: String of up to 4 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.OSBMCManagementPassThrough (Read Only)

Description: Indicates whether OS-BMC Management Pass Through capability is supported. Indicates whether OS-BMC Management Pass Through capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.OmniPath (Read Only)

Description: Indicates whether Omni-Path functionality is supported. Indicates whether Omni-Path functionality is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.OnChipThermalSensor (Read Only)

Description: Indicates whether an on-chip thermal sensor is available. Indicates whether an on-chip thermal sensor is available.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.PCIDeviceID (Read Only)

Description: PCI Device ID reported by the controller when operating in non-NPar mode only. The value of the attribute is undefined for controllers operating in NPar mode that change their device IDs or support multiple PCI Device IDs at the partition level. PCI Device ID of the controller.
Legal Values: String of up to 4 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.PKey (Read or Write)

Description: PKey ID to be used by PXE boot in the InfiniBand environment PKey ID to be used by PXE boot in InfiniBand fabrics. Enter a number in the range 0-65535.
Legal Values: Integer values from 0 to 65535.
Default Value: 0
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.PXEBootSupport (Read Only)

Description: Indicates whether the PXE Boot capability is supported. Indicates whether PXE Boot capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.PortGUID (Read Only)

Description: The Permanent Port GUID assigned during manufacturing. Permanent Port GUID assigned during manufacturing.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.RDMANICModeOnPort (Read or Write)

Description

Enable/Disable the NIC + RDMA personality on the port. This setting is for when operating in non-NPar mode only. Note: This personality type may be specified as the port default if RDMA traffic can be supported irrespective of any other device mode or setting. Specify use of the port for both L2-Ethernet and RDMA traffic. [Vendor may want to customize type of RDMA supported].

Legal Values

Enabled
Disabled

Default Value

Varies

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.RXFlowControl (Read Only)

Description: Indicates whether Receive (RX) Flow control capability is supported. Indicates whether Receive (RX) Flow control capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.RemotePHY (Read Only)

Description: Indicates whether RemotePHY capability is supported. Indicates whether RemotePHY capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.SNAPI (Read Only)

Description: Indicates the adapter supports SNAPI functionality by either special interfacing to the PCI slot connector or via cabling to another PCI slot. Indicates whether SNAPI functionality is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.SNAPIState (Read Only)

Description

Indicates whether SNAPI functionality is enabled. Note: Implement only if SNAPI support is set to Available Indicates whether SNAPI functionality is enabled

Legal Values

Enabled
Disabled

Default Value

None

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.SocketDirect (Read Only)

Description: Indicates whether Socket Direct functionality is supported. Indicates whether Socket Direct functionality is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.SocketDirectState (Read Only)

Description: Indicates whether Socket Direct functionality is enabled. Indicates whether Socket Direct functionality is enabled
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.TOESupport (Read Only)

Description: Indicates whether TCP/IP Offload Engine capability is supported Indicates whether TCP/IP Offload Engine capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.TXBandwidthControlMaximum (Read Only)

Description: Indicates whether Transmit(TX) Bandwidth Control Maximum capability is supported Indicates whether Transmit(TX) Bandwidth Control Maximum capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.TXBandwidthControlMinimum (Read Only)

Description: Indicates whether Transmit (TX) Bandwidth Control Minimum capability is supported Indicates whether Transmit (TX) Bandwidth Control Minimum capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.TXFlowControl (Read Only)

Description: Indicates whether Transmit (TX) Flow Control capability is supported Indicates whether Transmit (TX) Flow Control capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VPI (Read Only)

Description: Indicates whether Virtual Protocol Interconnect (VPI) functionality is supported. Indicates whether Virtual Protocol Interconnect (VPI) functionality is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtFIPMacAddr (Read or Write)

Description: Programmatically assignable FIP-MAC address for FCoE. Virtual addresses written will also generate corresponding VWWNN and VWWPN addresses as defined in Y741D. The supported method of reverting to the permanent FIP-MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature enablement. Programmatically assignable FIP-MAC address for FCoE.
Legal Values: String of up to 17 ASCII characters.
Default Value: 00:00:00:00:00:00
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtIscsiMacAddr (Read or Write)

Description: Programmatically assignable MAC address for iSCSI offload. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature enablement. Programmatically assignable MAC address for iSCSI offload.
Legal Values: String of up to 17 ASCII characters.
Default Value: 00:00:00:00:00:00
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtMacAddr (Read or Write)

Description: Programmatically assignable MAC address. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent MAC address is by writing 0s to the virtual MAC. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature enablement. Programmatically assignable MAC address for port.
Legal Values: String of up to 17 ASCII characters.
Default Value: 00:00:00:00:00:00
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtNodeGuid (Read or Write)

Description: Programmatically assignable Node GUID address used when only one PF is assigned to the port. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent Node GUID address is by writing 0s to the virtual Node GUID. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. Programmatically assignable Node GUID address.
Legal Values: String of up to 19 ASCII characters.
Default Value: 0000:0000:0000:0000
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtNvmeTcpMacAddr (Read or Write)

Description: Programmatically assignable MAC address for NVMe/TCP offload. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent MAC address is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address should be readable at all times, irrespective of feature enablement. Programmatically assignable MAC address for NVMe/TCP offload.
Legal Values: String of up to 17 ASCII characters.
Default Value: 00:00:00:00:00:00
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtPortGUID (Read or Write)

Description: Programmatically assignable Port GUID. Virtual addresses written will also generate corresponding GUID as defined in Y741D. The supported method of reverting to the permanent GUID is by writing 0s as the virtual address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature enablement. Programmatically assignable Port GUID assigned during manufacturing.
Legal Values: String of up to 19 ASCII characters.
Default Value: 0000:0000:0000:0000
Write Privilege: N/A
License Required: Not Applicable
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtWWN (Read or Write)

Description: Programmatically assignable Fibre Channel World Wide Node Name identifier for FCoE. Virtual addresses written will also be modified by subsequent writes to the VirtFIP-MAC addesss as defined in Y741D. The supported method of clearing this virtual address is by writing 0s as the address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. Programmatically assignable Fibre Channel World Wide Node Name identifier for FCoE.
Legal Values: String of up to 23 ASCII characters.
Default Value: 00:00:00:00:00:00:00:00
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.VirtWWPN (Read or Write)

Description: Programmatically assignable Fibre Channel World Wide Port Name identifier for FCoE. Virtual addresses written will also be modified by subsequent writes to the VirtFIP-MAC addesss as defined in Y741D The supported method of clearing this virtual address is by writing 0s as the address. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. . Programmatically assignable Fibre Channel World Wide Port Name identifier for FCoE.
Legal Values: String of up to 23 ASCII characters.
Default Value: 00:00:00:00:00:00:00:00
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.WWN (Read Only)

Description: Fibre Channel World Wide Node Name identifier for FCoE Fibre Channel World Wide Node Name identifier for FCoE
Legal Values: String of up to 23 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.WWPN (Read Only)

Description: Fibre Channel World Wide Port Name identifier for FCoE Fibre Channel World Wide Port Name identifier for FCoE.
Legal Values: String of up to 23 ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.iSCSIBootSupport (Read Only)

Description: Indicates whether iSCSI Boot is supported. Indicates whether iSCSI Boot is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.iSCSIDualIPVersionSupport (Read Only)

Description: Indicates support for simultaneous IPv4 and IPv6 configurations of the iSCSI initiator and iSCSI primary and secondary targets. Indicates support for simultaneous IPv4 and IPv6 configurations of iSCSI initiator and iSCSI primary and secondary targets.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.iSCSIOffloadSupport (Read Only)

Description: Indicates whether the iSCSI Offload capability is supported. Indicates whether the iSCSI Offload capability is supported.
Legal Values: String of ASCII characters.
Default Value: None
Write Privilege: N/A
License Required: Express License
Dependency: None
Notes: Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.VndrConfigPage.iScsiOffloadMode (Read or Write)

Description

Enable/Disable the iSCSI offload personality on the port. This setting is for when operating in non-NPar mode only. Specify use of the port for iSCSI offload storage traffic.

Legal Values

Enabled
Disabled

Default Value

Disabled

Write Privilege

N/A

License Required

Express License

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.100Gbps1WoL (Read or Write)

Description

Speed selector for the specified link speed to be advertised to the link partner for Vaux operations including Wake On LAN and shared LOM management features. If an implementation only supports one pre-OS link speed configuration for boot, WoL and management, then this speed attribute should not be implemented. When WakeOnLanLnkSpeedMethod is set to Auto, then this attribute should be greyed-out. Note: The speed selection shall only be included if it is supported in the implementation. Advertise 100 Gbps (1 lane of 100 Gb)

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.100Gbps2WoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.100Gbps4WoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.100MbpsWoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.10GbpsWoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.10MbpsWoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.1GbpsWoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.200Gbps1WoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.200Gbps2WoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.200Gbps4WoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.25GbpsWoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.40GbpsWoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.50Gbps1WoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.

NIC.WakeOnLanLnkSpeedConfig.50Gbps2WoL (Read or Write)

Description

Legal Values

True
False

Default Value

True

Write Privilege

N/A

License Required

Not Applicable

Dependency

None

Notes

Single function mode attributes are listed under the VndrConfigPage group. However, if Network Partitioning (NPAR) is enabled, the attributes are instead listed under the ConfigureForm group.