Dell EMC SmartFabric OS10 User Guide Release 10.5.1

Port-groups on S5200F-ON switches

On the S5200F-ON series switches, port-groups determine the available front-panel Ethernet ports and supported breakout interfaces.

When you convert a port to a particular mode, all ports that belong to the port group also operate at the same mode. For example, if you convert the Ethernet 1/1/1 interface to 10g-4x, all other interfaces that belong to port-group 1/1/1 namely, 1/1/2, 1/1/3, and 1/1/4 also operate at 10g-4x mode.

The following shows the supported port groups and breakout modes on the S5212F-ON switch:

OS10# show port-group

Port-group            Mode           Ports     		  FEM
port-group1/1/1       Eth 10g-4x     1  2  3  4     -
port-group1/1/2       Eth 10g-4x     5  6  7  8     -
port-group1/1/3       Eth 10g-4x     9  10  11  12  -
port-group1/1/4       Eth 100g-1x    13             -
port-group1/1/5       Eth 100g-1x    14             -
port-group1/1/6       Eth 100g-1x    15             -

The following shows the supported port groups and breakout modes on the S5224F-ON switch:

OS10# show port-group
Port-group            Mode           Ports          FEM
port-group1/1/1       Eth 10g-4x     1  2  3  4     -
port-group1/1/2       Eth 10g-4x     5  6  7  8     -
port-group1/1/3       Eth 10g-4x     9  10  11  12  -
port-group1/1/4       Eth 10g-4x     13  14  15  16 -
port-group1/1/5       Eth 10g-4x     17  18  19  20 -
port-group1/1/6       Eth 10g-4x     21  22  23  24 -
port-group1/1/7       Eth 100g-1x    25             -
port-group1/1/8       Eth 100g-1x    26             -
port-group1/1/9       Eth 100g-1x    27             -
port-group1/1/10      Eth 100g-1x    28             -

The following shows the supported port groups and breakout modes on the S5248F-ON switch:

OS10# show port-group
Port-group      Mode       Ports        FEM
port-group1/1/1 Eth 25g-4x 1 2 3 4      -
port-group1/1/2 Eth 25g-4x 5 6 7 8      -
port-group1/1/3 Eth 25g-4x 9 10 11 12   -
port-group1/1/4 Eth 25g-4x 13 14 15 16 	-
port-group1/1/5 Eth 25g-4x 17 18 19 20 	-
port-group1/1/6 Eth 25g-4x 21 22 23 24 	-
port-group1/1/7 Eth 25g-4x 25 26 27 28 	-
port-group1/1/8 Eth 25g-4x 29 30 31 32 	-
port-group1/1/9 Eth 25g-4x 33 34 35 36 	-
port-group1/1/10 Eth 25g-4x 37 38 39 40 -
port-group1/1/11 Eth 25g-4x 41 42 43 44 -
port-group1/1/12 Eth 25g-4x 45 46 47 48 -
port-group1/1/13 Eth 100g-2x 49 50      -
port-group1/1/14 Eth 100g-2x 51 52      -
port-group1/1/15 Eth 100g-1x 53         -
port-group1/1/16 Eth 100g-1x 54 					-
port-group1/1/17 Eth 100g-1x 55 					-
port-group1/1/18 Eth 100g-1x 56 					- 

The following shows the supported port groups and breakout modes on the S5296F-ON switch:

OS10# show port-group

Port-group            Mode           Ports              FEM
port-group1/1/1       Eth 25g-4x     1  2  3  4    		   -
port-group1/1/2       Eth 25g-4x     5  6  7  8     		 -
port-group1/1/3       Eth 25g-4x     9  10  11  12      -
port-group1/1/4       Eth 25g-4x     13  14  15  16     -
port-group1/1/5       Eth 25g-4x     17  18  19  20     -
port-group1/1/6       Eth 25g-4x     21  22  23  24     -
port-group1/1/7       Eth 25g-4x     25  26  27  28     -
port-group1/1/8       Eth 25g-4x     29  30  31  32     -
port-group1/1/9       Eth 25g-4x     33  34  35  36     -
port-group1/1/10      Eth 25g-4x     37  38  39  40     -
port-group1/1/11      Eth 10g-4x     41  42  43  44     -
port-group1/1/12      Eth 25g-4x     45  46  47  48     -
port-group1/1/13      Eth 25g-4x     49  50  51  52     -
port-group1/1/14      Eth 25g-4x     53  54  55  56     -
port-group1/1/15      Eth 25g-4x     57  58  59  60     -
port-group1/1/16      Eth 25g-4x     61  62  63  64     -
port-group1/1/17      Eth 25g-4x     65  66  67  68     -
port-group1/1/18      Eth 25g-4x     69  70  71  72     -
port-group1/1/19      Eth 25g-4x     73  74  75  76     -
port-group1/1/20      Eth 25g-4x     77  78  79  80     -
port-group1/1/21      Eth 25g-4x     81  82  83  84     -
port-group1/1/22      Eth 25g-4x     85  86  87  88     -
port-group1/1/23      Eth 25g-4x     89  90  91  92     -
port-group1/1/24      Eth 25g-4x     93  94  95  96     -
port-group1/1/25      Eth 100g-1x    97         					 -
port-group1/1/26      Eth 100g-1x    98         					 -
port-group1/1/27      Eth 100g-1x    99          				 -
port-group1/1/28      Eth 100g-1x    100         				 -
port-group1/1/29      Eth 100g-1x    101         				 -
port-group1/1/30      Eth 100g-1x    102         				 -
port-group1/1/31      Eth 100g-1x    103         				 -
port-group1/1/32      Eth 100g-1x    104         				 -

To configure breakout modes:

1. Configure a port group in CONFIGURATION mode. Enter 1/1 for node/slot and the port group number.

   port-group node/slot/port-group

2. Configure the breakout mode in PORT-GROUP mode.

   mode Eth breakout-mode

   • 100g-2x — Split a port group into two 100GE interface.
   • 100g-1x — Set a port group to 100GE mode.
   • 50g-4x — Split a port group into four 50GE interfaces.
   • 50g-2x — Split a port group into two 50GE interfaces.
   • 40g-2x — Split a port group into two 40GE interfaces for use with a QSFP+ 40GE transceiver.
   • 40g-1x — Set a port group to 40GE mode for use with a QSFP+ 40GE transceiver.
   • 25g-8x — Split a port group into eight 25GE interfaces.
   • 25g-4x — Split a port group into four 25GE interfaces.
   • 10g-8x — Split a port group into eight 10GE interfaces.
   • 10g-4x — Split a port group into four 10GE interfaces.
3. Return to CONFIGURATION mode.

   exit

4. Enter Interface breakout mode to configure other settings, such as, speed.

   interface ethernet node/slot/port[:subport]

OS10# configure terminal
OS10(config)# port-group 1/1/1
OS10(conf-pg-1/1/1)# mode Eth 10g-4x
OS10(conf-pg-1/1/1)# exit
OS10(config)# interface ethernet 1/1/1:1
OS10(conf-if-eth1/1/1:1)# speed
1000 Set speed to 1000 Mbps
10000 Set speed to 10000 Mbps
auto Automatic Settings (default)
OS10(conf-if-eth1/1/1:1)# speed 1000