Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products

PowerProtect Data Manager 19.13 Storage Direct User Guide

Supported Internet Protocol versions

PowerProtect Data Manager and its components support IPv4 and IPv6 addresses in certain configurations.

Table 1. Supported configurationsSupported configurations
Component Internet Protocol
PowerProtect Data Manager core IPv4 only or both IPv4 and IPv6
PowerProtect Data Manager cloud deployments (AWS, Azure, GCP) IPv4 only
NOTE: Despite other entries in this chart to the contrary, if PowerProtect Data Manager is deployed to a cloud environment, no component in the cloud can use IPv6.
VM Direct, TSDM, and Search IPv4 only or IPv6 only
NOTE: Virtual machines that are backed up must use the same protocol that VM Direct uses. Virtual machines can use both IPv4 and IPv6, even though VM Direct and TSDM cannot.
Application agents integrated with PowerProtect Data Manager:
NOTE: If both IPv4 and IPv6 are configured and the PowerProtect Data Manager FQDN is used, the agent uses IPv6 for network communication.
  • File System
IPv4, IPv6, or both
  • Microsoft Exchange Server
IPv4 only or both IPv4 and IPv6
  • Microsoft SQL Server (Application Direct)
IPv4, IPv6, or both
  • Microsoft SQL Server (VM Direct)
IPv4 only or IPv6 only
NOTE: Only the Microsoft SQL Server agent supports VM Direct.
  • Oracle RMAN
IPv4, IPv6, or both
  • SAP HANA
IPv4, IPv6, or both
  • Storage Direct
IPv4 only
Stand-alone application agents IPv4 only
Network-attached storage (NAS) IPv4, IPv6, or both
Kubernetes IPv4 only
PowerProtect Data Manager management IPv4 or IPv6
PowerProtect DD communication IPv4 or IPv6
Report Browser IPv4 only
NOTE: The Report Browser fails to generate reports if PowerProtect Data Manager is configured to use both IPv4 and IPv6.
SupportAssist IPv4, IPv6, or both
Syslog Log Server Gateway IPv4 or IPv6

The following limitations and considerations apply.

Communication with components

If PowerProtect Data Manager is configured to only use one protocol, all components it communicates with must also use that protocol. If some components that PowerProtect Data Manager communicates with use IPv4 and others use IPv6, PowerProtect Data Manager must be configured to use both IPv4 and IPv6.

DD systems and DDVE

If a DD system or a DDVE instance uses only IPv6, the required IPv6 interface must be manually selected when a protection policy is added or edited.

Disaster recovery

Recovering a PowerProtect Data Manager server might result in a conflict with protection-policy configurations. For instance, if the recovered server is configured to use only IPv4, a protection policy that is configured to use IPv6 cannot run.

Name resolution

Name resolution and reverse IP lookup must be configured to ensure the following:

  • Fully qualified domain names of PowerProtect Data Manager, its components, and DD components resolve to a valid IPv4 or IPv6 address.
  • If both IPv4 and IPv6 addresses are used for DD, both addresses resolve to the same FQDN.
  • All IPv4 and IPv6 addresses are valid and reachable.

Server updates

IPv6 is only supported with new installations of PowerProtect Data Manager 19.12 or later . Using IPv6 after updating from PowerProtect Data Manager 19.11 or earlier is unsupported.

Search Engine indexing and adding IPv6 to an IPv4-only system

If you add IPv6 to an IPv4-only system, indexing from any existing Search Engine cluster becomes unavailable. After adding IPv6, you must delete all IPv4 Search Engine nodes to remove the Search Engine cluster, and then add new IPv6 nodes to a new cluster.

Unlike other PowerProtect Data Manager components, if IPv6 is used with a Search Engine, the FQDN of all Search Engine nodes and related DD systems must always resolve to an IPv6 address and never to an IPv4 address.

Storage Policy Based Management

If using vCenter or ESXi 7.0u2 or earlier with only IPv6, SPBM providers must be added using their PowerProtect Data Manager FQDN.

Service Unavailable messages with the vSphere Client PowerProtect plug-in

If vCenter uses the vSphere Client PowerProtect plug-in with IPv6 and the vCenter host is added to PowerProtect Data Manager using its IPv6 address or FQDN, Service Unavailable messages might be seen for the protected virtual machine. Backups and restores of the protected virtual machine are unaffected, and these messages can be ignored.

Uncompressed IPv6 formatting

Network interfaces that exist on a DD 7.4.x or earlier system and that are configured to use an uncompressed IPv6 format cannot be discovered. An example of an uncompressed IPv6 format is 2620:0000:0170:0597:0000:0000:0001:001a. An example of a compressed IPv6 format is 2620:0:170:597::1:1a. To use these network interfaces, reconfigure them to use either an IPv4 address or a compressed IPv6 address, and then initiate a discovery.


Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\