Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.

Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

logging

Configure an IP address or host name of a Syslog server where logging messages are sent. Multiple logging servers of both IPv4 and/or IPv6 can be configured.

Syntax
logging {ip-address | ipv6-address | hostname} {{udp {port}} | {tcp {port}} [vrf vrf-name]

To disable logging, use the no logging command.

Parameters
ip-address
Enter the IPv4 address in dotted decimal format.
ipv6-address
Enter the IPv6 address in the x:x:x:x::X format.
NOTE The :: notation specifies successive hexadecimal fields of zeros.
hostname
Enter the name of a host already configured and recognized by the switch.
udp   
Enter the keyword udp to enable transmission of log message over UDP followed by port number. The default port is 514
tcp                          
Enter the keyword tcp to enable transmission of log message over TCP followed by port number.
vrf vrf-name
(Optional) Enter the keyword vrf and then the name of the VRF to enable the logging process in VRF mode.
NOTE Use this attribute to specify the VRF that is used to contact the host. By default, the default VRF is used.
Defaults
Disabled.
Command Modes
CONFIGURATION
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100–ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.5(0.1)
Added udp and tcp keywords for the Z9500.
9.5(0.0)
Added udp and tcp keywords for the S4810, S4820T, S6000, Z9000, and MXL.
9.4.(0.0)
Added support for VRF.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
9.2(0.0)
Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
8.4.1.0
Added support for IPv6.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
E-Series legacy command
Usage Information
Multiple logging servers of both IPv4 and/or IPv6 can be configured.
Related Commands
  • logging on — enables the logging asynchronously to logging buffer, console, Syslog server, and terminal lines.
  • logging trap — enables logging to the Syslog server based on severity.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\