Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

show cam-acl

Show space allocated for IPv6 ACLs.

Syntax
show cam-acl
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100–ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.7.0
Introduced on the S4810.
8.4.2.1
Introduced on the S-Series.
8.4.2.0
Introduced on the E-Series.
7.8.1.0
Introduced on the C-Series.
Example
show cam-acl (non default)
DellEMC(conf)# cam-acl l2acl 2 ipv4acl 4 ipv6acl 4 ipv4qos 2 l2qos 1 l2pt 0 ipmacacl 0 vman-qos 0 ecfmacl  0 
DellEMC#show cam-acl        

-- Chassis Cam ACL --
             Current Settings(in block sizes) 
                   1 block = 128 entries 
L2Acl        :         2
Ipv4Acl      :         4
Ipv6Acl      :         4
Ipv4Qos      :         2
L2Qos        :         1
L2PT         :         0
IpMacAcl     :         0
VmanQos      :         0
VmanDualQos  :         0
EcfmAcl      :         0
FcoeAcl      :         0
iscsiOptAcl  :         0
ipv4pbr      :         0
vrfv4Acl     :         0
Openflow     :         0
fedgovacl    :         F3940

-- stack-unit 1 --
           Current Settings(in block sizes)
                   1 block = 128 entries 
L2Acl        :         2
Ipv4Acl      :         4
Ipv6Acl      :         4
Ipv4Qos      :         2
L2Qos        :         1
L2PT         :         0+F394
IpMacAcl     :         0
VmanQos      :         0
VmanDualQos  :         0
EcfmAcl      :         0
FcoeAcl      :         0
iscsiOptAcl  :         0
ipv4pbr      :         0
vrfv4Acl     :         0
Openflow     :         0
fedgovacl    :         0

DellEMC#    
Example (Manual Profiles)
DellEMC# show cam-acl

-- Chassis Cam ACL --
         Current Settings(in block sizes)
L2Acl   :         2
Ipv4Acl :         2
Ipv6Acl :         4
Ipv4Qos :         2
L2Qos   :         3

-- Line card 4 --
          Current Settings(in block sizes)
L2Acl   :         2
Ipv4Acl :         2
Ipv6Acl :         4
Ipv4Qos :         2
L2Qos   :         3

DellEMC#
Related Commands
  • cam-acl — configure CAM profiles to support IPv6 ACLs.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\