Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

show interfaces status

To display status information on a specific interface only, display a summary of interface information or specify a stack-unit slot and interface.

Syntax
show interfaces [interface | stack—unit slot-number] status
Parameters
interface
(OPTIONAL) Enter one of the following keywords the interface information:
  • For a port channel interface, enter the keywords port-channel then a number.
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms.
  • For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
  • For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4.
stack-unit slot-number
(OPTIONAL) Enter the keyword stack-unit then the slot number. The range is from 0 to 5.
Defaults
None
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100–ON.
9.9(0.0)
Added support to display the interface configurations corresponding to a range of ports.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
8.5.1.0
Added support for 4-port 40G line cards on the E-Series.
8.1.1.0
Introduced on the E-Series.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
7.5.1.0
Introduced on the E-Series.
Example
DellEMC# show interfaces status
Port    Description  Status  Speed     Duplex  Vlan
Te 1/1               Up      1000 Mbit Auto    --
Te 1/2               Down    Auto      Auto    1
Te 1/3               Down    Auto      Auto    1
Te 1/4               Down    Auto      Auto    --
Te 1/5  DellPort     Up      1000 Mbit Auto    30-130
Te 1/6               Down    Auto      Auto    --
Te 1/7               Down    Auto      Auto    --
Te 1/8               Up      1000 Mbit Auto    1502,1504,1506-1508,1602
Te 1/9               Down    Auto      Auto    --
Te 1/10              Down    Auto      Auto    --
Te 1/11              Down    Auto      Auto    --
Te 1/12              Down    Auto      Auto    --
Te 1/13              Down    Auto      Auto    --
Te 1/14              Down    Auto      Auto    --
Te 1/15              Down    Auto      Auto    --
Te 1/16              Down    Auto      Auto    -
DellEMC#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\