Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.

Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

show ip bgp filter-list

View the routes that match the filter lists.

Syntax
show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] filter-list as-path-name
Parameters
vrf vrf-name
(OPTIONAL) Enter the keyword vrf and then the name of the VRF to view route information that matches the filter lists corresponding to that VRF.
ipv4 multicast
(OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes.
ipv4 unicast
(OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
ipv6 unicast
(OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes.
as-path-name
Enter an AS-PATH access list name. The range is 140 characters.
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Added the ipv4 multicast and ipv6 unicast parameters.
9.4.(0.0)
Added support for VRF.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
7.8.1.0
Introduced on the S-Series.
7.7.1.0
Introduced on the C-Series.
Usage Information

The following describes the show ip bgp filter-list hello command shown in the following example.

Field
Description
Path source codes
Lists the path sources shown to the right of the last AS number in the Path column:
  • i = internal route entry
  • a = aggregate route entry
  • c = external confederation route entry
  • n = network route entry
  • r = redistributed route entry
Next Hop
Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table.
Metric
Displays the BGP route’s metric, if assigned.
LocPrf
Displays the BGP LOCAL_PREF attribute for the route.
Weight
Displays the route’s weight.
Path
Lists all the ASs the route passed through to reach the destination network.
Example
DellEMC# show run as-path a1
!
ip as-path access-list a1
 permit 500
DellEMC# 

DellEMC# show ip bgp filter-list a1
BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0
BGP local router ID is 192.168.11.5
Status codes: s suppressed, S stale, d dampened, h history, * valid, > best
Path source: I - internal, a - aggregate, c - confed-external, r - redistributed
             n - network,  D - denied,  S - stale
Origin codes: i - IGP, e - EGP, ? - incomplete

    Network            Next Hop            Metric     LocPrf Weight Path
*>  55.0.0.0/24        172.16.0.2                                 0 200 400 500 600 i
*>  66.0.0.0/24        172.16.0.2                                 0 200 500 i
DellEMC#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\