Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.

Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

show ip ospf statistics

Display OSPF statistics.

Syntax
show ip ospf [process-id | vrf vrf-name] statistics global | [interface name {neighbor router-id}]
Parameters
process-id
Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
vrf vrf-name
Enter the keyword vrf followed by the name of the VRF to display statistics corresponding to the OSPF process that is tied to a specific VRF.
global
Enter the keyword global to display the packet counts received on all running OSPF interfaces and packet counts OSPF neighbors receive and transmit.
interface name
(OPTIONAL) Enter the keyword interface then one of the following interface keywords and slot/port or number information:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a port channel interface, enter the keywords port-channel then a number.
  • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
neighbor router-id
(OPTIONAL) Enter the keyword neighbor then the neighbor’s router-id in dotted decimal format (A.B.C.D.).
Defaults
None
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.4.(0.0)
Added support for VRF.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
7.8.1.0
Added support for Multi-Process OSPF.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
7.4.1.0
Introduced on the E-Series.
Usage Information
The following describes the show ip ospf statistics process-id global command shown in the following example.
Row Heading
Description
Total
Displays the total number of packets the OSPF process receives/transmits.
Error
Displays the error count while receiving and transmitting packets by the OSPF process.
Hello
Number of OSPF Hello packets.
DDiscr
Number of database description packets.
LSReq
Number of link state request packets.
LSUpd
Number of link state update packets.
LSAck
Number of link state acknowledgement packets.
TxQ-Len
The transmission queue length.
RxQ-Len
The reception queue length.
Tx-Mark
The highest number mark in the transmission queue.
Rx-Mark
The highest number mark in the reception queue.
Hello-Q
The queue, for transmission or reception, for the hello packets.
LSR-Q
The queue, for transmission or reception, for the link state request packets.
Other-Q
The queue, for transmission or reception, for the link state acknowledgement, database description, and update packets.

The following describes the error definitions for the show ip ospf statistics process-id global command.

Error Type
Description
Intf_Down
Received packets on an interface that is either down or OSPF is not enabled.
Non-Dr
Received packets with a destination address of ALL_DRS even though SELF is not a designated router.
Self-Org
Receive the self originated packet.
Wrong_Len
The received packet length is different to what was indicated in the OSPF header.
Invld-Nbr
LSA, LSR, LSU, and DDB are received from a peer which is not a neighbor peer.
Nbr-State
LSA, LSR, and LSU are received from a neighbor with stats less than the loading state.
Auth-Error
Simple authentication error.
MD5-Error
MD5 error
Cksum-Err
Checksum Error
Version
Version mismatch
AreaMismatch
Area mismatch
Conf-Issue
The received hello packet has a different hello or dead interval than the configuration.
No-Buffer
Buffer allocation failure.
Seq-no
A sequence no errors occurred during the database exchange process.
Socket
Socket Read/Write operation error.
Q-overflow
Packets dropped due to queue overflow.
Unknown-Pkt
Received packet is not an OSPF packet.
Example
DellEMC# show ip ospf 1 statistics global

OSPF Packet Count
   Total Error Hello DDiscr LSReq LSUpd LSAck
RX 10    0     8     2      0     0     0
TX 10    0     10    0      0     0     0

OSPF Global Queue Length
         TxQ-Len RxQ-Len Tx-Mark Rx-Mark
Hello-Q  0       0       0       2
LSR-Q    0       0       0       0
Other-Q  0       0       0       0

Error packets (Only for RX)

Intf-Down  0   Non-Dr     0   Self-Org 0
Wrong-Len  0   Invld-Nbr  0   Nbr-State 0
Auth-Err   0   MD5-Err    0   Chksum 0
Version    0   AreaMis    0   Conf-Issues 0
No-Buffer  0   Seq-No     0   Socket 0
Q-OverFlow 0   Unkown-Pkt 0

Error packets (Only for TX)

Socket Errors    0
DellEMC#
Usage Information
The show ip ospf process-id statistics command displays the error packet count received on each interface as:
  • The hello-timer remaining value for each interface
  • The wait-timer remaining value for each interface
  • The grace-timer remaining value for each interface
  • The packet count received and transmitted for each neighbor
  • Dead timer remaining value for each neighbor
  • Transmit timer remaining value for each neighbor
  • The LSU Q length and its highest mark for each neighbor
  • The LSR Q length and its highest mark for each neighbor
Example (Statistics)
DellEMC(conf-if-te-1/6)# do show ip ospf statistics
Interface TenGigabitEthernet 1/6
  Error packets (Receive statistics)
     Intf-Down 0 Non-Dr 0 Self-Org 0
     Wrong-Len 0 Invld-Nbr 0 Nbr-State 0
     Auth-Error 0 MD5-Error 0 Cksum-Err 0
     Version 0 AreaMisMatch 0 Conf-Issue 0
     SeqNo-Err 0 Unknown-Pkt 0 Bad-LsReq 0
     RtidZero 0
  Neighbor ID 4.4.4.4
     Packet Statistics
                Hello DDiscr LSReq LSUpd LSAck
        RX 5 2 1 3 2
        TX 6 5 1 3 3
     Timers
        Hello 0 Wait 0 Grace 0
        Dead 39 Transmit 4
     Queue Statistics
        LSU-Q-Len 0 LSU-Q-Wmark 1
        LSR-Q-Len 0 LSR-Q-Wmark 1

DellEMC(conf-if-te-1/6)#
Related Commands

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\