Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.

Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

show ip pim snooping tib

Display information from the tree information base (TIB) PIM-SM snooping discovered about multicast group members and states.

Syntax
show ip pim snooping tib [vlan vlan-id] [group-address [source-address]]
Parameters
vlan vlan-id
(OPTIONAL) Enter a VLAN ID to display TIB information PIM-SM snooping discovered on a specified VLAN. The valid VLAN IDs range is from 1 to 4094.
group-address
(OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D) to display TIB information PIM-SM snooping discovered for a specified multicast group.
source-address
(OPTIONAL) Enter the source address in dotted decimal format (A.B.C.D) to display TIB information PIM-SM snooping discovered for a specified multicast source.
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.5(0.1)
Introduced on the Z9500.
8.3.19.0
Introduced on the S4820T.
8.3.12.0
Introduced on the S4810.
8.4.1.1
Introduced on the E-Series.
Usage Information
The following describes the show ip pim snooping tib commands shown in the following example.
Field
Description
(S, G)
Displays the entry in the PIM multicast snooping database.
uptime
Displays the amount of time the entry has been in the PIM multicast route table.
expires
Displays the amount of time until the entry expires and is removed from the database.
RP
Displays the IP address of the RP/source for this entry.
flags
List the flags to define the entries:
  • S = PIM Sparse Mode
  • C = directly connected
  • L = local to the multicast group
  • P = route was pruned
  • R = the forwarding entry is pointing toward the RP
  • F = Dell EMC Networking OS is registering this entry for a multicast source
  • T = packets were received via Shortest Tree Path
  • J = first packet from the last hop router is received and the entry is ready to switch to SPT
  • K=acknowledge pending state
Incoming interface
Displays the reverse path forwarding (RPF) interface towards the RP/ source.
RPF neighbor
Displays the next hop from this interface towards the RP/source.
Outgoing interface list:
Lists the interfaces that meet one of the following criteria:
  • a directly connect member of the Group
  • statically configured member of the Group
  • received a (*,G) Join message
Example
DellEMC# show ip pim snooping tib

PIM Multicast Snooping Table
Flags: J/P - (*,G) Join/Prune, j/p - (S,G) Join/Prune
       SGR-P - (S,G,R) Prune
Timers: Uptime/Expires
* : Inherited port

(*, 225.1.2.1), uptime 00:00:01, expires 00:02:59, RP 165.87.70.1, flags: J
  Incoming interface: Vlan 2, RPF neighbor 0.0.0.0
  Outgoing interface list:
    TenGigabitEthernet 2/11 RPF 165.87.32.2 00:00:01/00:02:59
    TenGigabitEthernet 2/13 Upstream Port   -/-

DellEMC# show ip pim snooping tib vlan 2 225.1.2.1 165.87.1.7

PIM Multicast Snooping Table
Flags: J/P - (*,G) Join/Prune, j/p - (S,G) Join/Prune
       SGR-P - (S,G,R) Prune
Timers: Uptime/Expires
* : Inherited port

(165.87.1.7, 225.1.2.1), uptime 00:00:08, expires 00:02:52, flags: j
  Incoming interface: Vlan 2, RPF neighbor 0.0.0.0
  Outgoing interface list:
    TenGigabitEthernet 2/11 Upstream Port    -/-
    TenGigabitEthernet 2/13 DR Port          -/-
    TenGigabitEthernet 2/20 RPF 165.87.32.10 00:00:08/00:02:52

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\