Dell Command Line Reference Guide for the S4048–ON System 9.14.2.5

PDF

debug ip bgp

Display all information on BGP, including BGP events, keepalives, notifications, and updates.

Syntax
debug ip bgp [ vrf vrf-name | A.B.C.D | X:X:X:X::X | peer-group peer-group-name] [in | out]

To disable all BGP debugging, use the no debug ip bgp command.

Parameters
vrf vrf-name
Enter the keyword vrf and then the name of the VRF to debug BGP information corresponding to that VRF.
NOTE: Use this attribute to debug BGP protocol operations corresponding to either a default or non-default VRF.
A.B.C.D
Enter the IPv4 address of the neighbor in dotted decimal format.
X:X:X:X::X
(OPTIONAL) Enter an IPv6 address.
peer-group peer-group-name
Enter the keywords peer-group then the name of the peer group to debug.
in
(OPTIONAL) Enter the keyword in to view only information on inbound BGP routes.
out
(OPTIONAL) Enter the keyword out to view only information on outbound BGP routes.
A.B.C.D
Enter the IP address of peer in the A.B.C.D format.
X:X:X:X::X
Enter the IPv6 IP address of peer in the X:X:X:X::X format.
dampening
Enter the keyword dampening to view BGP dampening.
events
Enter the keyword events to view BGP protocol events.
ipv4
Enter the ipv4 IP address to view the IPV4 route information.
ipv6
Enter the ipv6 IP address to view the IPV6 route information.
keepalives
Enter the keyword keepalives to view BGP keepalives.
notifications
Enter the keyword notifications to view BGP notifications.
soft-reconfiguration
Enter the keywords soft-reconfiguration to view only information on inbound BGP soft reconfiguration.
updates
Enter the keyword updates to view BGP updates.
Command Modes
EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000–ON.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
9.4.(0.0)
Added support for VRF.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
7.8.1.0
Introduced on the S-Series.
7.7.1.0
Introduced on the C-Series.
Usage Information

To view information on both incoming and outgoing routes, do not include the in and out parameters in the debugging command. The in and out parameters cancel each other; for example, if you enter the debug ip bgp in command and then enter the debug ip bgp out command, you do not see information on the incoming routes.

Entering a no debug ip bgp command removes all configured debug commands for BGP.

Related Commands

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\