Dell Command Line Reference Guide for the S4048–ON System 9.14.2.5

PDF

mac-address-table static (for Multicast MAC Address)

For multicast mode of network load balancing (NLB), configure a static multicast MAC address, associate the multicast MAC address with the VLAN used to switch Layer 2 multicast traffic, and add output ports that will receive multicast streams on the VLAN. To delete a configured static multicast MAC address from the MAC address table on the router, enter the no mac-address-table static multicast-mac-address command.

Syntax
mac-address-table static multicast-mac-address multicast vlan vlan-id range-output {single-interface | interface-list | interface-range}

To remove a MAC address, use the no mac-address-table static multicast-mac-address output interface vlan vlan-id command.

Parameters
multicast-mac-address
Enter the 48-bit hexadecimal address in nn:nn:nn:nn:nn:nn format.
multicast
Enter a vlan port to where L2 multicast MAC traffic is forwarded.
NOTE: Use this option if you want multicast functionality in an L2 VLAN without IGMP protocols.
output interface
For a multicast MAC address, enter the keyword output then one of the following interfaces for which traffic is forwarded:
  • For a Port Channel interface, enter the keywords port-channel then a number.
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
output-range interface
For a multicast MAC address, enter the keyword output-range then one of the following interfaces to indicate a range of ports for which traffic is forwarded:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a Management interface, enter the keyword managementethernet followed by slot/port numbers.
  • For a Port Channel interface, enter the keywords port-channel followed by a number.
  • For a port channel interface, enter the keywords port-channel then a number.
  • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
vlan vlan-id
Enter the keyword vlan then a VLAN ID number from 1 to 4094.
Defaults
Not configured.
Command Modes
CONFIGURATION
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100–ON.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.3(0.0)
Added support for multicast MAC address on the MXL platform.
Example (Multicast)
mac-address-table static 01:00:5E:01:00:01 {multicast vlan 2 output—range Te 1/2,Te 1/3

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\