Dell Command Line Reference Guide for the S4048–ON System 9.14.2.5

PDF

show ip bgp peer-group

Allows you to view information on the BGP peers in a peer group.

Syntax
show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] peer-group [peer-group-name [detail | summary]]
Parameters
vrf vrf-name
(OPTIONAL) Enter the keyword vrf to view information on BGP peers in a peer group corresponding to that VRF.
NOTE: You can use this attribute to view information on BGP peers in a peer group that correspond to either a default or a non-default VRF.
ipv4 multicast
(OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes.
ipv4 unicast
(OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
ipv6 unicast
(OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes.
peer-group-name
(OPTIONAL) Enter the name of a peer group to view information about that peer group only.
detail
(OPTIONAL) Enter the keyword detail to view detailed status information of the peers in that peer group.
summary
(OPTIONAL) Enter the keyword summary to view status information of the peers in that peer group. The output is the same as that found in the show ip bgp summary command.
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Added the ipv4 multicast and ipv6 unicast parameters. Introduced on S6000–ON.
9.4.(0.0)
Added support for VRF.
9.2(1.0)
Introduced on the Z9500.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.8.0
Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters.
8.3.7.0
Introduced on the S4810.
7.8.1.0
Introduced on the S-Series.
7.7.1.0
Introduced on the C-Series.
Usage Information

The following describes the show ip bgp peer-group command shown in the following example.

Line beginning with:
Description
Peer-group
Displays the peer group’s name.
Administratively shut
Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed.
BGP version
Displays the BGP version supported.
Minimum time
Displays the time interval between BGP advertisements.
For address family
Displays IPv4 Unicast as the address family.
BGP neighbor
Displays the name of the BGP neighbor.
Number of peers
Displays the number of peers currently configured for this peer group.
Peer-group members:
Lists the IP addresses of the peers in the peer group. If the address is outbound optimized, an * is displayed next to the IP address.
Example
DellEMC# show ip bgp peer-group
Peer-group port0, remote AS 200
BGP version 4
Minimum time between advertisement runs is 30 seconds
For address family: IPv4 Unicast
BGP neighbor is port0, peer-group external
Update packing has 4_OCTET_AS support enabled

Number of peers in this group 1
Maximum limit on the accepted connections 256


 Peer-group members (* - outbound optimized):
172.16.0.2
DellEMC#
Related Commands

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\