Dell Command Line Reference Guide for the S4048–ON System 9.14.2.5

PDF

show ip pim tib

View the PIM tree information base (TIB).

S4048–ON

Syntax
show ip pim [vrf vrf-name] tib [group-address [source-address]]
Parameters
vrf vrf-name
(OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
group-address
(OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D).
source-address
(OPTIONAL) Enter the source address in dotted decimal format (A.B.C.D).
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Added support for VRF. Introduced on the S6000-ON.
9.5(0.1)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.12.0
Introduced on the S4810.
8.3.11.1
Introduced on the Z9000.
8.1.1.0
Introduced on the E-Series.
7.8.1.0
Introduced on the S-Series.
Usage Information
The following describes the show ip pim tib command shown in the following example.
Field
Description
(S, G)
Displays the entry in the multicast PIM database.
uptime
Displays the amount of time the entry has been in the PIM route table.
expires
Displays the amount of time until the entry expires and is removed from the database.
RP
Displays the IP address of the RP/source for this entry.
flags
List the flags to define the entries:
  • D = PIM Dense Mode
  • S = PIM Sparse Mode
  • C = directly connected
  • L = local to the multicast group
  • P = route was pruned
  • R = the forwarding entry is pointing toward the RP
  • F = Dell EMC Networking OS is registering this entry for a multicast source
  • T = packets were received via Shortest Tree Path
  • J = first packet from the last hop router is received and the entry is ready to switch to SPT
  • K = acknowledge pending state
Incoming interface
Displays the reverse path forwarding (RPF) interface towards the RP/ source.
RPF neighbor
Displays the next hop from this interface towards the RP/source.
Outgoing interface list:
Lists the interfaces that meet one of the following criteria:
  • a directly connect member of the Group
  • statically configured member of the Group
  • received a (*,G) Join message
Example
DellEMC# do show ip pim tib

PIM Multicast Routing Table
Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned,
       R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, 
       M - MSDP created entry, A - Candidate for MSDP Advertisement
       K - Ack-Pending State
Timers: Uptime/Expires
Interface state: Interface, next-Hop, State/Mode

(*, 225.1.1.1), uptime 00:40:16, expires 00:00:00, RP 20.40.4.4, flags: SCJ
  Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4
  Outgoing interface list:
    Vlan 2006  Forward/Sparse   00:06:21/Never   

(20.10.4.9, 225.1.1.1), uptime 00:06:21, expires 00:02:06, flags: CT
  Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4
  Outgoing interface list:
    Vlan 2006  Forward/Sparse   00:06:21/Never   

(*, 225.1.1.2), uptime 00:40:15, expires 00:00:00, RP 20.40.4.4, flags: SCJ
  Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4
  Outgoing interface list:
    Vlan 2006  Forward/Sparse   00:06:21/Never   

(20.10.4.9, 225.1.1.2), uptime 00:06:21, expires 00:02:06, flags: CT
  Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4
  Outgoing interface list:
    Vlan 2006  Forward/Sparse   00:06:21/Never
DellEMC#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\