Dell Command Line Reference Guide for the S4048–ON System 9.14.2.5

PDF

show ipv6 neighbors

Display IPv6 discovery information. Entering the command without options shows all IPv6 neighbor addresses stored on the control processor (CP).

Syntax
show ipv6 neighbors [vrf vrf-name] [ipv6-address| interface interface]
Parameters
vrf vrf-name
(OPTIONAL) Enter the keyword vrf and the name of the VRF to display the neighbors corresponding to that VRF.
NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed.
ipv6-address
Enter the IPv6 address of the neighbor in the x:x:x:x::x format.
NOTE: The :: notation specifies successive hexadecimal fields of zero.
interface interface
Enter the keyword interface then the interface type and slot/port or number information:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a Management interface, enter the keyword managementethernet followed by slot/port numbers.
  • For a Port Channel interface, enter the keywords port-channel followed by a number.
  • For a port channel interface, enter the keywords port-channel then a number.
  • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
Defaults
None
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Added support for VRF. Introduced on the S6000–ON.
9.2(1.0)
Introduced on the Z9500.
9.0.0.0
Introduced on the Z9000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.1
Introduced on the S4810.
Example
DellEMC# show ipv6 neighbors
IPv6 Address  Expires(min) Hardware Address State  Interface VLAN CPU
--------------------------------------------------------------------
100::1          0.03       00:00:00:00:00:22 DELAY  Te 1/12 -    CP
fe80::200:ff:fe00:22 232   00:00:00:00:00:22 STALE  Te 1/12 -    CP
500::1          0.60       00:01:e8:17:5c:af REACH  Te 1/13 -    CP
fe80::200:ff:fe00:17 232   00:00:00:00:00:29 REACH  Te 1/14 -    CP
900::1          0.60       00:01:e8:17:5c:b1 STALE  Po 23   -    CP
400::1          0.60       00:01:e8:17:5c:ae REACH  Te 1/2  Vl 100 CP
DellEMC#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\