Dell Command Line Reference Guide for the S4048–ON System 9.14.2.5

PDF

show redundancy

Display the current redundancy configuration.

Syntax
show redundancy
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.2(0.0)
Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
8.1.1.0
Introduced on the E-Series.
7.5.1.0
Introduced on the C-Series.
7.6.1.0
Introduced on the E-Series.
Usage Information
The following describes the show redundancy command shown in the following example.
Field
Description
RPM Status
Displays the following information:
  • Slot number of the RPM.
  • Whether the RPM is Primary or Standby.
  • The state of the RPM: Active, Standby, Booting, or Offline.
  • Whether the link to the second RPM is up or down.
PEER RPM Status
Displays the state of the second RPM, if present
RPM Redundancy Configuration
Displays the following information:
  • which RPM is the preferred Primary on next boot (the redundancy primary command)
  • the data sync method configured (the redundancy synchronize command)
  • the failover type (you cannot change this type; it is software-dependent). Hot Failover means that the running configuration and routing table are applied on secondary RPM. Fast Failover means that the running configuration is not applied on the secondary RPM until failover occurs, and the routing table on line cards is cleared during failover.
  • the status of auto booting the RPM (the redundancy disable-auto-reboot command)
  • the parameter for auto failover limit control (the redundancy auto-failover-limit command)
RPM Failover Record
Displays the following information:
  • RPM failover counter (to reset the counter, use the redundancy reset-counter command)
  • the time and date of the last RPM failover
  • the reason for the last RPM failover
Last Data Sync Record
Displays the data sync information and the timestamp for the data sync:
  • Start-up Config is the contents of the startup-config file.
  • Line Card Config is the line card types configured and interfaces on those line cards.
  • Runtime Event Log is the contents of the Event log.
  • Running Config is the current running-config.

This field only appears when you enter the command from the Primary RPM.

Example
DellEMC# show redundancy

-- RPM Status --
------------------------------------------------
RPM Slot ID:         1
RPM Redundancy Role: Primary
RPM State:           Active
RPM SW Version:      7.5.1.0
Link to Peer:        Up

-- PEER RPM Status --
------------------------------------------------
RPM State:       Standby
RPM SW Version:  7.5.1.0

-- RPM Redundancy Configuration --
------------------------------------------------
Primary RPM:         rpm0
Auto Data Sync:      Full
Failover Type:       Hot Failover
Auto reboot RPM:     Enabled
Auto failover limit: 3 times in 60 minutes

-- RPM Failover Record --
------------------------------------------------
Failover Count:           1
Last failover timestamp:  Jul 13 2007 21:25:32
Last failover Reason:     User request

-- Last Data Block Sync Record: --
------------------------------------------------
Line Card Config:  succeeded Jul 13 2007 21:28:53
Start-up Config:   succeeded Jul 13 2007 21:28:53
SFM Config State:  succeeded Jul 13 2007 21:28:53
Runtime Event Log: succeeded Jul 13 2007 21:28:53
Running Config:    succeeded Jul 13 2007 21:28:53
DellEMC#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\