Dell Command Line Reference Guide for the S4048–ON System


show vrrp ipv6

View the active IPv6 VRRP groups. If no VRRP groups are active, the Dell EMC Networking OS returns No Active VRRP group.

show vrrp ipv6 [vrid] [interface] [brief] [vrf vrf-name]
(OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255.
Enter the following keywords and the number information:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a port channel interface, enter the keywords port-channel, and then a number.
  • For a VLAN interface, enter the keyword vlan, and then a number from 1 to 4094.
(OPTIONAL) Enter the keyword brief to view a table of information on the VRRP groups.
vrf vrf-name
Enter the keyword vrf then the name of the VRF to view IPv6 VRRP groups corresponding to that VRF.
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Introduced on the S6010-ON and S4048T-ON.
Introduced on the S3148.
Introduced on the S6100–ON.
Introduced on the S3100 series.
Introduced on the Z9100–ON.
Introduced on the S4048-ON.
Introduced on the S3048-ON.
Added support for VRF. Introduced on the S6000-ON.
Introduced on the Z9500.
Introduced on the S4820T.
Introduced on the S4810.
Introduced on the E-Series.
Usage Information
The following describes the show vrrp ipv6 command.
Line starting with
Displays the interface, VRRP group ID, and network address. If the interface is not sending VRRP packets, appears as the network IP address.
VRF instance to which the VRRP group interface belongs.
State: master...
Displays the interface’s state:
  • Na/If (not available)
  • master (MASTER virtual router)
  • backup (BACKUP virtual router)

Also displays the interface’s priority and IP address of the MASTER.

Hold Down:...
Displays additional VRRP configuration information:
  • Hold Down displays the hold down timer interval in seconds.
  • Preempt displays TRUE if preempt is configured and FALSE if preempt is not configured.
  • AdvInt displays the Advertise Interval in seconds.
Adv rcvd:...
Displays counters for the following:
  • Adv rcvd displays the number of VRRP advertisements received on the interface.
  • Adv sent displays the number of VRRP advertisements sent on the interface.
  • Bad pkts rcvd displays the number of invalid packets received on the interface.
Virtual MAC address
Displays the virtual MAC address of the VRRP group.
Virtual IP address
Displays the virtual IP address of the VRRP router to which the interface is connected.
Tracking states...
Displays information on the tracked interfaces or objects configured for a VRRP group (track command), including:
  • UP or DOWN state of the tracked interface or object (Up or Dn).
  • Interface type and slot/port[/subport] or object number, description, and time since the last change in the state of the tracked object.
  • Cost subtracted from the VRRP group priority if the state of the tracked interface/object goes DOWN.
DellEMC# show vrrp ipv6
TenGigabitEthernet 5/6, IPv6 VRID: 255, Version: 3, Net:
State: Master, Priority: 101, Master: fe80::201:e8ff:fe7a:6bb9 (local)
Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec
Accept Mode: FALSE, Master AdvInt: 100 centisec
Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 64
Virtual MAC address:
Virtual IP address:
  1::255 fe80::255

Rate this content

Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\