Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8

PDF

ipv6 neighbor

Configure a static entry in the IPv6 neighbor discovery.

Syntax
ipv6 neighbor [vrf vrf-name] {ipv6-address} {interface interface} {hardware_address}

To remove a static IPv6 entry from the IPv6 neighbor discovery, use the no ipv6 neighbor [vrf vrf-name] {ipv6-address} {interface interface} command.

Parameters
vrf vrf-name
(Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF.
ipv6-address
Enter the IPv6 address of the neighbor in the x:x:x:x::x format.
NOTE: The :: notation specifies successive hexadecimal fields of zero.
interface interface
Enter the keyword interface then the interface type and slot/port or number information:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
  • For a port channel interface, enter the keywords port-channel then a number.
  • For a Null interface, enter the keyword null then the Null interface number.
  • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
  • For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383.
hardware_address
Enter a 48-bit hardware MAC address in nn:nn:nn:nn:nn:nn format.
Defaults
None
Command Modes
CONFIGURATION
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Added support for VRF. Introduced on the S6000-ON.
9.2(1.0)
Introduced on the Z9500.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.1
Introduced on the S4810.
Usage Information
Neighbor Discovery Protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4. It defines mechanisms for solving problems, such as:
  • Router discovery: Hosts can locate routers residing on a link.
  • Prefix discovery: Hosts can discover address prefixes for the link.
  • Parameter discovery .
  • Address autoconfiguration — configuration of addresses for an interface .
  • Address resolution — mapping from IP address to link-layer address.
  • Next-hop determination.
  • Neighbor Unreachability Detection (NUD): Determine that a neighbor is no longer reachable on the link.
  • Duplicate Address Detection (DAD): Allow a node to check whether a proposed address is already in use.
  • Redirect: The router can inform a node about a better first-hop.

Use the ipv6 neighbor command to manually configure the IPv6 address of a neighbor to be discovered by the switch.


Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\