Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8

PDF

load-balance hg

Choose the traffic flow parameters the hash calculation uses while distributing the traffic across internal higig links.

Syntax
[no] load-balance hg {ip-selection | ipv6-selection [source-ip | source-ipv6 | source-port-id | source-module-id | dest-ip | dest-ipv6 | dest-port-id | dest-module-id | protocol | vlan | L4-source-port | L4-dest-port ] | mac [source-mac | source-port-id | source-module-id | dest-mac | dest-port-id | dest-module-id | vlan | ethertype | source-dest-mac ] | tunnel [ipv4-over-ipv4 | ipv4-over-gre-ipv4 | mac-in-mac]}
Parameters
{{ip-selection| ipv6-selection [source-ip | source-ipv6 | source-port-id | source-module-id | dest-ip | dest-ipv6 | dest-port-id | dest-module-id | protocol | vlan | L4-source-port | L4-dest-port ]
To use IPv4 key fields in hash computation, enter the keyword ip-selection then one of the parameters. To use IPv6 key fields in hash computation, enter the keyword ipv6-selection then one of the parameters.
  • source-ip — Use IPv4 src-ip field in hash calculation.
  • source-ipv6 — Use IPv6 src-ip field in hash calculation
  • source-port-id — Use src-port-id field in hash calculation.
  • source-module-id — Use src-module-id field in hash calculation.
  • dest-ip — Use IPv4 dest-ip field in hash calculation.
  • dest-ipv6 — Use IPv6 dest-ip field in hash calculation
  • dest-port-id — Use dest-port-id field in hash calculation.
  • dest-module-id — Use dest-module-id field in hash calculation.
  • protocol — Use IPv4 protocol field in hash calculation.
  • vlan — Use vlan field in hash calculation.
  • L4-source-port — Use IPv4 L4-source-port field in hash calculation.
  • L4-dest-port — Use IPv4 L4-dest-port field in hash calculation.
mac [source-mac | source-port-id | source-module-id | dest-mac | dest-port-id | dest-module-id | vlan | ethertype | source-dest-mac ]
To use MAC key fields in hash computation, enter the keyword mac then one of the parameters:
  • source-mac — Use source-mac field in hash calculation.
  • source-port-id — Use src-port-id field in hash calculation.
  • source-module-id — Use src-module-id field in hash calculation.
  • dest-mac — Use dest-mac field in hash calculation.
  • dest-port-id — Use dest-port-id field in hash calculation.
  • dest-module-id — Use dest-module-id field in hash calculation.
  • vlan — Use vlan field in hash calculation .
  • ethertype — Use Ethertype field in hash calculation.
  • source-dest-mac — Use SMAC and DMAC fields in hash calculation.
tunnel [ipv4-over-ipv4 | ipv4-over-gre-ipv4 | mac-in-mac]}
To use tunnel key fields in hash computation, enter the keyword tunnel then one of the parameters:
  • ipv4-over-ipv4 — Use ipv4-over-ipv4 field in hash calculation.
  • ipv4-over-gre-ipv4 — Use ipv4-over-gre-ipv4 field in hash calculation.
  • mac-in-mac — Use mac-in-mac field in hash calculation.
Defaults
IP selection 5-tuples (source-ip dest-ip vlan protocol L4-source-port L4-dest-port).
Command Modes
CONFIGURATION
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100–ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.0.2.0
Introduced on the S6000.
9.0.0.0
Added support for IPv6.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\