Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8

PDF

mac-address-table static

Associate specific MAC or hardware addresses to an interface and VLANs.

Syntax
mac-address-table static mac-address {multicast vlan vlan-id output—range interface}{output interface vlan vlan-id}

To remove a MAC address, use the no mac-address-table static mac-address output interface vlan vlan-id command.

Parameters
mac-address
Enter the 48-bit hexadecimal address in nn:nn:nn:nn:nn:nn format.
multicast
Enter a vlan port to where L2 multicast MAC traffic is forwarded.
NOTE: Use this option if you want multicast functionality in an L2 VLAN without IGMP protocols.
output interface
For a unicast MAC address, enter the keyword output then one of the following interfaces for which traffic is forwarded:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a port channel interface, enter the keywords port-channel then a number.
output-range interface
For a multicast MAC address, enter the keyword output-range then one of the following interfaces to indicate a range of ports for which traffic is forwarded:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a port channel interface, enter the keywords port-channel then a number.
vlan vlan-id
Enter the keyword vlan then a VLAN ID number from 1 to 4094.
Defaults
Not configured.
Command Modes
CONFIGURATION
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.8(2.0)
Introduced on the S3100 series.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000–ON.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
9.1(0.0)
Added support for output range parameter for S4810 and Z9000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.5.1.0
Added support for 4-port 40G line cards on the E-Series.
8.3.7.0
Introduced on the S4810.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
pre-6.2.1.1
Introduced on the E-Series.
Example (Unicast)
mac-address-table static 00:01:00:00:00:01 {output Te 1/2 vlan 2}
Example (Multicast)
mac-address-table static 01:00:5E:01:00:01 {multicast vlan 2 output—range Te 1/2, Te 1/3}
Related Commands

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\