Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8

PDF

match ip precedence

Use IP precedence values as a match criteria.

Syntax
[seq sequence number] match {ip | ipv6 | ip-any} precedence ip-precedence-list [set-ip-dscp value]

To remove IP precedence as a match criteria, use the no match {ip | ipv6 | ip-any} precedence ip-precedence-list [[multicast] set-ip-dscp value] command.

Parameters
seq sequence number
(OPTIONAL) Enter the keyword seq then the sequence number. The range is from 1 to 100. By default, the sequence number are assigned in multiples of five.
ip
Enter the keyword ip to support IPv4 traffic.
ipv6
Enter the keyword ipv6 to support IPv6 traffic.
ip-any
Enter the keyword ip-any to support IPv4 and IPv6 traffic.
ip-precedence-list
Enter the IP precedence value(s) as the match criteria. Separate values by commas — no spaces ( 1,2,3 ) or indicate a list of values separated by a hyphen (1-3). The range is from 0 to 7.
set-ip-dscp value
(OPTIONAL) Enter the keywords set-ip-dscp then the IP DSCP value. The matched traffic is marked with the DSCP value. The range is from 0 to 63.
Defaults
none
Command Modes
CLASS-MAP CONFIGURATION (config-class-map)
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.12(0.0)
Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms.
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.5(0.1)
Introduced on the Z9500.
9.5(0.0)
Added support for the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
7.7.1.0
Added the keyword multicast . Added support for the DSCP Marking option for the S-Series.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series. Added support for the DSCP Marking option.
6.1.1.1
Introduced on the E-Series.
Usage Information

To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria.

The match ip precedence command and the match ip dscp command are mutually exclusive.

Up to eight precedence values can be matched in one match statement. For example, to indicate the IP precedence values 0 1 2 3, enter either the match ip precedence 0-3 or match ip precedence 0,1,2,3 command.

NOTE: Only one of the IP precedence values must be a successful match criterion, not all of the specified IP precedence values must match.
Related Commands

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\