Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8

PDF

redirect

Configure a rule for the redirect list.

Syntax
redirect {ip-address | slot/port} | tunnel tunnel-id}[track <obj-id>] {ip-protocol-number | protocol-type [bit]} {source mask | any | host ip-address} {destination mask | any | host ip-address} [operator]
To remove this filter, use one of the following:
  • Use the no seq sequence-number command if you know the filter’s sequence number.
  • You can also use the no redirect {ip-address | slot/port}| tunnel tunnel-id}[track <obj-id>] {ip-protocol-number [bit] | protocol-type} {source mask | any | host ip-address} {destination mask | any | host ip-address} [operator] command.
Parameters
redirect
Enter the keyword redirect to assign the sequence to the redirect list.
ip-address
Enter the IP address of the forwarding router.
slot/port
Enter the keyword slot / port followed by the slot/port information.
tunnel
Enter the keyword tunnel to configure the tunnel setting.
tunnel-id
Enter the keyword tunnel-id to redirect the traffic.
track
Enter the keyword track to enable the tracking.
track <obj-id>
Enter the keyword track <obj-id> to track object-id.
ip-protocol-number
Enter a number from 0 to 255 for the protocol identified in the IP protocol header.
protocol-type
Enter one of the following keywords as the protocol type:
  • icmp for internet control message protocol
  • ip for any internet protocol
  • tcp for transmission control protocol
  • udp for user datagram protocol
bit
(OPTIONAL) For the TCP protocol type only, enter one or a combination of the following TCP flags:
  • ack = acknowledgement
  • fin = finish (no more data from the user)
  • psh = push function
  • rst = reset the connection
  • syn = synchronize sequence number
  • urg = urgent field
source
Enter the IP address of the network or host from which the packets were sent.
mask
Enter a network mask in /prefix format (/x).
any
Enter the keyword any to specify that all traffic is subject to the filter.
host ip-address
Enter the keyword host then the IP address to specify a host IP address.
destination
Enter the IP address of the network or host to which the packets are sent.
operator
(OPTIONAL) For TCP and UDP parameters only. Enter one of the following logical operand:
  • eq = equal to
  • neq = not equal to
  • gt = greater than
  • lt = less than
  • range = inclusive range of ports (you must specify two ports for theport command parameter.)
Defaults
None
Command Modes
REDIRECT-LIST
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.7(0.0)
Added support for the track-id on the S4810, S4820T, S6000, and Z9000.
9.5(0.1)
Introduced on the Z9500.
9.4(0.0)
Introduced on the S4810, S4820T, S6000, and Z9000.
8.4.2.1
Introduced on the C-Series and S-Series.
8.4.2.0
Introduced on the E-Series.
7.7.1.0
Introduced on the E-Series.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\