Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8

PDF

seq

To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number.

Syntax
deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor]
To remove this filter, you have two choices:
  • Use the no seq sequence-number command if you know the filter’s sequence number.
  • Use the no deny {any | mac-source-address mac-source-address-mask} command.
Parameters
any
Enter the keyword any to specify that all routes are subject to the filter.
mac-source-address
Enter a MAC address in nn:nn:nn:nn:nn:nn format.
mac-source-address-mask
(OPTIONAL) Specify which bits in the MAC address must match. If no mask is specified, a mask of 00:00:00:00:00:00 is applied (in other words, the filter allows only MAC addresses that match).
count
(OPTIONAL) Enter the keyword count to count packets processed by the filter.
byte
(OPTIONAL) Enter the keyword byte to count bytes processed by the filter.
log
(OPTIONAL) Enter the keyword log to include ACL messages in the log.
threshold-in msgs count
(OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
interval minutes
(OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes.
monitor
(OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see “Flow-based Monitoring” in the Port Monitoring section in the Dell EMC Networking OS Configuration Guide.
Defaults
Not configured
Command Modes
CONFIGURATION-MAC ACCESS LIST-STANDARD
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.8(2.0)
Introduced on the S3100 series.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.8(0.0)
Added the no-drop parameter.
9.7(0.0)
Introduced on the S6000–ON.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
8.1.1.0
Introduced on the E-Series.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
7.4.1.0
Added the monitor option.
6.1.1.0
Introduced on the E-Series.
Usage Information

When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.

NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead.
Related Commands
  • deny — configure a filter to drop packets.
  • permit — configure a filter to forward packets.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\