Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8

PDF

show crypto ipsec sa ipv6

Display the IPsec security associations (SAs) used on OSPFv3 interfaces.

Syntax
show crypto ipsec sa ipv6 [interface interface]
Parameters
interface interface

(OPTIONAL) Displays information about the SAs used on a specified OSPFv3 interface, where interface is one of the following values:

  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a port channel interface, enter the keywords port-channel then a number.
  • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
Defaults
No default behavior or values.
Command Modes

EXEC

EXEC Privilege

Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.2(1.0)
Introduced on the Z9500.
9.1.(0.0)
Introduced on the S4810 and Z9000.
8.4.2.0
Introduced on the E-Series.
8.3.19.0
Introduced on the S4820T.
Usage Information

The show crypto ipsec sa ipv6 command output displays security associations set up for OSPFv3 links in IPsec authentication and encryption policies on the router.

Related Commands

show crypto ipsec policy – displays the configuration of IPsec authentication and encryption policies.

Example
DellEMC# show crypto ipsec policy
DellEMC# show crypto ipsec sa ipv6

Interface: TenGigabitEthernet 1/1
 Link Local address: fe80::201:e8ff:fe40:4d10
 IPSecv6 policy name: OSPFv3-1-500
 
 inbound ah sas
  spi : 500 (0x1f4)
   transform : ah-md5-hmac
   in use settings : {Transport, }
   replay detection support : N
   STATUS : ACTIVE

 outbound ah sas
  spi : 500 (0x1f4)
   transform : ah-md5-hmac
   in use settings : {Transport, }
   replay detection support : N
   STATUS : ACTIVE

 inbound esp sas

 outbound esp sas


Interface: TenGigabitEthernet 1/2
 Link Local address: fe80::201:e8ff:fe40:4d11
 IPSecv6 policy name: OSPFv3-1-600

 inbound ah sas

 outbound ah sas

 inbound esp sas
  spi : 600 (0x258)
   transform : esp-des esp-sha1-hmac
   in use settings : {Transport, }
   replay detection support : N
   STATUS : ACTIVE

 outbound esp sas
  spi : 600 (0x258)
   transform : esp-des esp-sha1-hmac
   in use settings : {Transport, }
   replay detection support : N
   STATUS : ACTIVE

show crypto ipsec sa ipv6 Command Fields

Field
Description
Interface
IPv6 interface
Link local address
IPv6 address of interface
IPSecv6 policy name
Name of the IPsec security policy applied to the interface.
inbound/outbound ah
Authentication policy applied to inbound or outbound traffic.
inbound/outbound esp
Encryption policy applied to inbound or outbound traffic.
spi
Security policy index number used to identify the policy.
transform
Security algorithm that is used to provide authentication, integrity, and confidentiality.
in use settings
Transform that the SA uses (only transport mode is supported).
replay detection support

Y: An SA has enabled the replay detection feature.

N: The replay detection feature is not enabled.

STATUS
ACTIVE: The authentication or encryption policy is enabled on the interface.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\