PowerEdge Servers Error and Event Messages Reference Guide

PDF

NVIF—Interface Event Messages

NVIF0001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure Maximum Transmission Unit(MTU) because the configured MTU value is greater than the maximum value.
Detailed Description
The Maximum Transmission Unit (MTU) cannot be configured because the value exceeds the limit identified in the message.
Recommended Response Action
Configure a valid MTU less than or equal to the value identified in the message and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the fanout on the interface because the interface fanout type is not HardwareDefault.
Detailed Description
Fanout from non-hardware default to non-hardware default is not allowed.
Recommended Response Action
Configure the interface to HardwareDefault and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the interface because the interface does not exist in the inventory.
Detailed Description
The interface can not be configured because the interface does not exist in the inventory.
Recommended Response Action
No response action required.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure autoneg because the interface does not support autoneg.
Detailed Description
The autoneg cannot be configured on the interface because the autoneg capability is not supported for this interface.
Recommended Response Action
No response action is required.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the configured speed for the interface because the entered value is not supported.
Detailed Description
The configured speed cannot be configured because the configured speed identified in the message is not supported.
Recommended Response Action
Enter a valid configured speed and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the Breakout property on the interface arg1 because the Breakout Capability validation has failed.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified in the message cannot be configured because the Breakout Capability validation has failed.
Recommended Response Action
Validate the Breakout Capability types for the interface and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the Breakout property on the interface arg1 because the requested breakout type is not supported.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified in the message cannot be configured because the interface does not support the requested breakout type.
Recommended Response Action
Validate the Breakout type for the interface and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the Breakout property on the interface arg1 because the resource validation has failed.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified on the message cannot be configured because the interface has associated configured resources.
Recommended Response Action
Unconfigure the resources for the interface and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the Breakout property on the interface arg1 because the VLAN association validation has failed.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified in the message cannot be configured because the interface member has associated vlan configuration.
Recommended Response Action
Unconfigure VLAN resources for the interface and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the Breakout property on the interface arg1 because the interface is part of the uplink.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified in the message cannot be configured because the interface member has associated FIP-VLAN configuration.
Recommended Response Action
Unconfigure FIP-VLAN resources for the interface and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the breakout property on the interface arg1 because the breakout member is part of an uplink.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified in the message cannot be configured because the member interface is associated with an uplink.
Recommended Response Action
Remove the breakout member from the uplink and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the breakout property on the interface arg1 because the breakout member is part of another port channel.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified in the message cannot be configured because the member interface is associated with another port channel.
Recommended Response Action
Remove the breakout member from the port channel member and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the Breakout property on the interface arg1 because the MX7116n Fabric Expander Module resource validation has failed.
Arguments
  • arg1 = Interface Name
Detailed Description
The Breakout property on the interface identified on the message cannot be configured because the interface has associated MX7116n Fabric Expander Module resources.
Recommended Response Action
Remove the cable between the MX7116n Fabric Expander Module and port group and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure Maximum Transmission Unit(MTU) on interface arg1 because the interface is of fibre channel (FC) type.
Arguments
  • arg1 = interface Name
Detailed Description
The Maximum Transmission Unit (MTU) cannot be configured on the specified interface because it is of Fibre Channel interface type.
Recommended Response Action
Choose a different interface type and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to complete the configuration request on the arg1 interface because the interface is an ICL port.
Arguments
  • arg1 = interface name
Detailed Description
The configuration request on the interface cannot be completed because the interface is an ICL port.
Recommended Response Action
Select another compatible interface and retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure Forward Error Correction (FEC) because the I/O Module (IOM) is not in SmartFabric mode.
Detailed Description
Unable to configure Forward Error Correction (FEC) because the I/O Module (IOM) is not in SmartFabric mode.
Recommended Response Action
Make sure that the I/O Module (IOM) is in SmartFabric mode by creating a SmartFabric that includes this IOM and then retry the operation. FEC can only be configured by the GUI when the device is in SmartFabric mode. If the IOM is in Full Switch mode, use the CLI.
Category
Configuration (NVIF = Interface)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0017

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure Forward Error Correction (FEC) for interface arg1 because the validation failed.
Arguments
  • arg1 = interface name
Detailed Description
Forward Error Correction (FEC) cannot be configured because the validation failed.
Recommended Response Action
Select a Forward Error Correction (FEC) mode that is supported by the interface, and then retry the operation.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0018

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to apply the configuration using the REST method because the switch is in Full Switch mode.
Detailed Description
The configuration cannot be applied because switch is in Full Switch mode.
Recommended Response Action
When the switch is in Full Switch mode, use the switch Command Line Interface (CLI) for configuring the port(s).
Category
Configuration (NVIF = Interface)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

NVIF0019

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to configure the selected port description attribute because the port description configuration is not supported on the port group.
Detailed Description
The selected port description attribute cannot be configured because the port description configuration is not supported on the port group.
Recommended Response Action
Select a different and compatible interface type and retry the operation. For information about compatible port descriptions on a port group, see the OpenManage Enterprise-Modular Users Guide available on the support site.
Category
Configuration (NVIF = Interface)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\