PowerEdge Servers Error and Event Messages Reference Guide

PDF

PR—Part Replacement Event Messages

PR1

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
A replacement part was detected for device: arg1
Arguments
  • arg1 = device name
Detailed Description
The specified device has been replaced.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR10

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Firmware update will not be performed. Firmware package is not present for arg1
Arguments
  • arg1 = device name
Detailed Description
The Part Replacement feature has detected a firmware difference and would apply firmware based on user settings for the system. However, the previous devices firmware update package is not present on the Lifecycle Controller.
Recommended Response Action
Use Unified Server Configurator or Dell update package to update device.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR11

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
A required license for the Part Replacement feature is not present, replacement action(s) will not be performed.
Detailed Description
A valid license for this feature is not present.
Recommended Response Action
Obtain license to utilize functionality.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR12

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Firmware update setting allows version upgrade only and will not be performed.
Detailed Description
The Part Replacement feature has detected a firmware difference and would apply firmware. However, user settings indicate that Part Replacement should perform the upgrade only and not a downgrade to an earlier firmware version.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR13

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Firmware mismatch detected. Configuration changes not applied.
Detailed Description
The Part Replacement feature detected a firmware difference and cannot apply the configuration changes. After the device firmware is updated, configuration changes can be applied.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR14

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The configuration could not be applied to device: arg1
Arguments
  • arg1 = device name
Detailed Description
The device identified in the message could not apply the configuration settings. This may indicate configuration changes since the last system inventory.
Recommended Response Action
Check the current system configuration and retry the operation.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR15

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to verify configuration changes for device: arg1
Arguments
  • arg1 = device name
Detailed Description
The configuration changes requested have not passed the device specific verification check and will not be applied.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR16

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Some of the configuration values could not be applied to device: arg1
Arguments
  • arg1 = device name
Detailed Description
The device could not apply some of the configuration settings. This may indicate configuration changes since the last system inventory or mutually exclusive settings.
Recommended Response Action
Check the current system configuration and ensure all settings are correct. If not, retry the operation.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR17

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Some of the configuration values stored for the previous device could not be applied to device: arg1
Arguments
  • arg1 = device name
Detailed Description
Some of the configuration values stored for the previous device could not be applied to the current device. This may be due to firmware version or other differences in the part.
Recommended Response Action
Check the devices configuration and ensure that the new configuration is correct for the system.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR18

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Firmware version difference detected for device: arg1
Arguments
  • arg1 = device name
Detailed Description
The Part Replacement feature has detected a firmware difference between the current and previous components. Depending on the Part Firmware Update setting value this may cause a firmware update to the replaced part.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR19

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job completed successfully.
Detailed Description
The specified job has completed successfully.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR2

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Configuration difference detected for device: arg1
Arguments
  • arg1 = device name
Detailed Description
The specified device configuration is different from the previous device configuration.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR20

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job in progress.
Detailed Description
The specified job is in progress.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR21

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job failed.
Detailed Description
The specified job did not complete successfully.
Recommended Response Action
Check the Lifecycle Log for more details associated with this failure then retry the operation.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR22

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Preparing new job.
Detailed Description
This is the initial job status value when a job is created. This message is no longer in use in Lifecycle Controller 2.0 as the job control functionality handles this operation.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR23

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job is ready for execution.
Detailed Description
The specified job is ready to start. It is waiting for scheduling from job control. This message is no longer in use in Lifecycle Controller 2.0 as the job control functionality handles this operation.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR24

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job cancelled.
Detailed Description
The specified job was cancelled. This could be due to user action or system error. This message is no longer in use in Lifecycle Controller 2.0 as the job control functionality handles this operation.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR25

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Missing or corrupt configuration database.
Detailed Description
The systems configuration database is missing or is unreadable. This may be due to a user action such as Lifecycle Controller Wipe or a replaced motherboard.
Recommended Response Action
Enable the Collect System Inventory on Restart attribute of the Lifecycle Controller and restart the system. Alternatively, use the Unified Server Configurator utility.
Category
Configuration (PR = Part Replacement)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR26

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Missing or corrupt job information.
Detailed Description
The configuration data associated with the specified job could not be located.
Recommended Response Action
Retry the operation. If this issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR27

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to allocate resources.
Detailed Description
The system ran out of memory while attempting to perform an operation. This has been deprecated.
Recommended Response Action
Retry the operation. If more than one operation was attempted retry them one at a time.
Category
Configuration (PR = Part Replacement)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR28

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to locate device in current configuration.
Detailed Description
The device that the job was intended for is no longer detected. This could be due to the device being removed, disabled, or a failure.
Recommended Response Action
If the device was removed, reinsert the device and retry the operation. If the device was disabled, re-enable the device and retry the operation.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR29

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to locate device in previous configuration.
Detailed Description
The device that the job was intended for has no previous information recorded. The request has failed as this information is required to initiate the operation. This has been deprecated.
Recommended Response Action
Enable the Collect System Inventory on Restart attribute of the Lifecycle Controller and restart the system. Alternatively, use the Unified Server Configurator utility.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR3

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Newer version of firmware found on device: arg1
Arguments
  • arg1 = device name
Detailed Description
The current component firmware version is higher than the replaced component firmware version.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR30

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job processing initialization failure.
Detailed Description
Operation validation was unsuccessful. The command, target and operation data are all validated before proceeding. If any of them are missing or incorrect the request is failed.
Recommended Response Action
Enable the Collect System Inventory on Restart attribute of the Lifecycle Controller and restart the system. After the system has restarted, retry the operation.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR31

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job completed with errors.
Detailed Description
All the tasks in the Job were attempted, but some did not complete successfully.
Recommended Response Action
Check the Lifecycle Log for more details associated with this warning then retry the operation if appropriate.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR32

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Failed verification of configuration changes.
Detailed Description
The configuration changes requested, for the indicated job, have not passed the device specific verification check and will not be applied.
Recommended Response Action
Check the scripts or company documentation and try again.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR33

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
System Board replacement detected.
Detailed Description
The platform system board was replaced.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR34

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
arg1 failed after exceeding retry attempt limit.
Arguments
  • arg1 = job ID
Detailed Description
The job was attempted but failed unexpectedly. An AC Power loss, system crash, or other interruption during the job processing can cause this failure.
Recommended Response Action
Recreate and resubmit the job.
Category
Configuration (PR = Part Replacement)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR35

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Power Supply slot arg1 firmware update will be performed during next system reboot.
Arguments
  • arg1 = PS slot number
Detailed Description
The Part Replacement feature has detected a firmware difference for the power supply and will start the firmware update process upon system reboot.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR36

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Version change detected for arg1 firmware. Previous version:arg2, Current version:arg3
Arguments
  • arg1 = device name
  • arg2 = previous version
  • arg3 = current version
Detailed Description
The system has detected a different firmware version than previously recorded for the indicated device. This may be due to a firmware update, rollback, or part replacement.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR37

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to update the firmware version of the replaced part because the Part Replacement Firmware Update feature is disabled in the Lifecycle Controller policy settings.
Detailed Description
The firmware version of the replaced part cannot be automatically updated because the Part Replacement Firmware Update feature is disabled in the Lifecycle Controller policy settings. The available options are: Disabled, Allow version upgrade only, and match firmware of the replaced part.
Recommended Response Action
Enable the policy settings by clicking LIfecycle Controller > Part Replacement Configuration. For example, Part Firmware Update > Match firmware of replaced part, Part Configuration Update > Apply Always.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR38

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to update the configuration of the replaced part because the Part Replacement Configuration Update feature is disabled in the Lifecycle Controller policy settings.
Detailed Description
The configuration of the replaced part cannot be automatically updated because the Part Replacement Configuration Update feature is disabled in the Lifecycle Controller policy settings. The available options are: Disabled, Apply always, and Allow only if firmware match.
Recommended Response Action
Enable the policy settings by clicking LIfecycle Controller > Part Replacement Configuration. For example, Part Firmware Update > Match firmware of replaced part, Part Configuration Update > Apply Always.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR39

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The Storage Controller is successfully installed. However, controller security settings are not automatically restored after replacing the Storage Controller.
Detailed Description
The Storage Controller is successfully installed. However, controller security settings are not automatically restored after replacing the Storage Controller.
Recommended Response Action
Enable the security feature on the replaced card using any of the iDRAC interfaces. To enable by using iDRAC GUI, click Actions > Edit > Security option in Storage > Controllers. To enable by using CLI, run the following RACADM command: racadm storage setencryptionmode: -mode SEKM. For more information, see the latest version of the iDRAC Users Guide available on the support site.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR4

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Older version of firmware found on device: arg1
Arguments
  • arg1 = device name
Detailed Description
The current component firmware version is lower than the previous component firmware version.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR5

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The configuration values stored for the previous device could not be applied to device: arg1
Arguments
  • arg1 = device name
Detailed Description
Some or all configuration values stored for the previous device could not be applied to the current device. This may be due to firmware version or other differences in the part.
Recommended Response Action
Check the devices configuration and ensure that the new configuration is correct for the system.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR6

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Configuration changes successfully applied to device: arg1
Arguments
  • arg1 = device name
Detailed Description
The configuration values stored for the previous device were applied to the current device.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

PR7

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
New device detected: arg1
Arguments
  • arg1 = device name
Detailed Description
The specified device was added to the system.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Trap/EventID
10299
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, LCD, OS Log, Power Off, Power Cycle
Applicable Event or Alert Types
CMC—Not Applicable

PR8

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Device not detected: arg1
Arguments
  • arg1 = device name
Detailed Description
The indicated device has been removed from the system, is no longer functioning, or has been disabled.
Recommended Response Action
If the part is present, make sure it is properly installed. Ensure that the device has not been disabled in the system BIOS or other configuration utility. If this issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category
Configuration (PR = Part Replacement)
Severity
Warning
Trap/EventID
10298
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, LCD, OS Log, Power Off, Power Cycle
Applicable Event or Alert Types
CMC—Not Applicable

PR9

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Firmware update operation initiated.
Detailed Description
The Part Replacement feature started the firmware update process based on Part Firmware Update attribute settings.
Recommended Response Action
No response action is required.
Category
Configuration (PR = Part Replacement)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\