PowerEdge Servers Error and Event Messages Reference Guide

SYS—System Info Event Messages

SYS001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation was successful.
Detailed Description: The operation requested successfully completed.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the operation due to an unknown error in iDRAC.
Detailed Description: The operation did not complete successfully because of an unknown error in iDRAC.
Recommended Response Action: Retry the action. If the issue persists, reset iDRAC.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Missing parameters: arg1.

Arguments

arg1 = parameter names

Detailed Description

One or more required parameters needed for the operation are missing.

Recommended Response Action

Refer to the Lifecycle Controller Remote Services documentation and retry the operation with the required parameters.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid parameter value for arg1.

Arguments

arg1 = parameter name

Detailed Description

The value provided for the specified parameter is invalid.

Recommended Response Action

Refer to the Lifecycle Controller Remote Services documentation and retry the operation with a valid value for the identified parameter.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: AttributeName array and AttributeValue array element count mismatch.
Detailed Description: The AttributeName input array and AttributeValue input array do not have the same number of elements.
Recommended Response Action: Verify AttributeName and AttributeValue pairs match and are valid. Refer to the Lifecycle Controller Remote Services documentation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to set read only attribute: arg1

Arguments

arg1 = attribute name

Detailed Description

The attribute being set is currently read-only and cannot be changed.

Recommended Response Action

Refer to the Lifecycle Controller Remote Services documentation for the specific attribute behavior.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Input out of range for arg1.

Arguments

arg1 = attribute name

Detailed Description

The input value for the attribute being set is not within the acceptable range for the attribute.

Recommended Response Action

Refer to the Lifecycle Controller-Remote Services documentation for the specific attribute and retry the operation with valid value within the range of the attribute.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid boolean in value for attribute: arg1.

Arguments

arg1 = attribute name

Detailed Description

The input value for the specified attribute is not a valid boolean value for the attribute.

Recommended Response Action

Refer to the Lifecycle Controller-Remote Services documentation and provide a valid boolean value for the specified attribute.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

String exceeds maximum length for attribute: arg1

Arguments

arg1 = attribute name

Detailed Description

Length of string for specified attribute exceeded the maximum length allowed.

Recommended Response Action

Check Lifecycle Controller-Remote Services documentation and retry the command with string value length less than maximum length allowed.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid character in value for attribute: arg1

Arguments

arg1 = attribute name

Detailed Description

The input value for the specified attribute is not valid.

Recommended Response Action

Refer to Lifecycle Controller-Remote Services documentation and provide valid attribute value for the specified attribute.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Pending configuration values are already committed, unable to perform another set operation.
Detailed Description: A configuration job is scheduled to apply pending set attribute operations. Set operations are not allowed if there is an existing configuration job for a component.
Recommended Response Action: Wait for the scheduled job to complete or delete the configuration jobs before attempting more set attribute operations. If issue still persists perform iDRAC reboot.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: User privileges are not sufficient to perform operation.
Detailed Description: The user credentials provided do not have appropriate privileges to perform the operation requested.
Recommended Response Action: Retry operation using user credentials that have appropriate privileges to perform the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid attribute name: arg1.

Arguments

arg1 = attribute name

Detailed Description

The attribute name provided for the requested operation does not exist on the target system or is invalid.

Recommended Response Action

For more information, see Lifecycle Controller-Remote Services documentation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid value for attribute: arg1

Arguments

arg1 = attribute name

Detailed Description

The value provided for the identified attribute is invalid.

Recommended Response Action

For more information, refer to the Lifecycle Controller-Remote Services documentation and provide a valid value for the identified attribute.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Job created successfully.
Detailed Description: The requested job has been created.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Job completed with errors
Detailed Description: All the operations in the Job were attempted, but some did not complete successfully.
Recommended Response Action: Review the Job content and verify the values are correct. For more information, see Lifecycle Controller Remote Services documentation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS017

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Job did not complete successfully.
Detailed Description: The job did not complete successfully.
Recommended Response Action: Verify the reason for the unsuccessful completion of the job by inspecting the Lifecycle Log entries related to the job. Correct the underlying cause of the unsuccessful completion and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS018

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Job completed successfully.
Detailed Description: The submitted job completed successfully.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS019

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Required dependency input not found.
Detailed Description: The input is missing a required dependency necessary for the operation.
Recommended Response Action: Provide the required dependency and retry. For more information, see Lifecycle Controller Remote Services documentation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS020

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid required Attribute value.
Detailed Description: The value provided for the required attribute is invalid.
Recommended Response Action: The value specified is not valid. Refer to the Lifecycle Controller Remote Services documentation for more information.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS021

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to set the value for arg1

Arguments

arg1 = attribute name

Detailed Description

The operation did not complete successfully because of incorrect parameters or internal firmware issues.

Recommended Response Action

Retry the operation. If the issue persists, do one of the following: 1) verify the value being set is correct, 2) reset the iDRAC.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS022

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Resource allocation failure.
Detailed Description: The operation could not complete because of an internal resource allocation issue with the firmware.
Recommended Response Action: Reset the iDRAC and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS023

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No configuration changes pending.
Detailed Description: There are no pending values to change.
Recommended Response Action: Ensure there are pending values for the attributes that need to be set and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS024

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because attribute dependency checking did not complete successfully.
Detailed Description: Unable to complete the operation because attribute dependency checking did not complete successfully. This attribute is dependent on a related attribute that has an incorrect value. The related attribute is the parent in a parent-child value dependency relationship and has an affect on what values the child attribute can have.
Recommended Response Action: Make sure the dependency related attribute has the correct value and retry the operation. For more information on attribute dependency, Refer to the Dell Lifecycle Controller Remote Services Quick Start Guide and Profile Documents available at the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS025

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to delete pending configuration.
Detailed Description: There are no pending configurations to be deleted.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS026

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to run the method because required parameter not entered for network share: arg1.

Arguments

arg1 = Share Type

Detailed Description

The network share cannot be accessed because the parameter identified in the message is not entered.

Recommended Response Action

Enter the missing parameter and retry the operation. For information about valid parameters to access a network share, see the iDRAC Users Guide available on the support site.

Category

Audit (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS027

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to access the network share because one or more invalid parameters are entered.
Detailed Description: The operation cannot be completed because invalid parameters are entered.
Recommended Response Action: Enter valid parameters and retry the operation. For information about valid parameters, see the Redfish API Guide available on the support site.
Category: Audit (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS028

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to start the export operation because arg1 operation is already running.

Arguments

arg1 = Method Name

Detailed Description

The export operation cannot be started because the operation identified in the message is already running.

Recommended Response Action

Wait for the current operation to complete, and then retry the operation.

Category

Audit (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS029

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unsupported parameter name arg1.

Arguments

arg1 = parameter name

Detailed Description

The parameter name is not supported.

Recommended Response Action

Remove the unsupported parameter and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS030

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Collecting component configuration information.
Detailed Description: Collecting the data required for component configuration.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS031

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Updating component configuration.
Detailed Description: The configuration is being applied to a component.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS032

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Staged component configuration is complete.
Detailed Description: The staged component configuration update performed in the UEFI environment on the host system is complete.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS033

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Staged component configuration completed with errors.
Detailed Description: The staged component configuration update performed in the UEFI environment on the host system has completed, but there were errors.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS034

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Performing component configuration for: arg1

Arguments

arg1 = device name

Detailed Description

The configuration operation for the specified device is in progress.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS035

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Some configuration values were not applied to: arg1

Arguments

arg1 = device name

Detailed Description

The component configuration operation was completed, however some of the configuration values were not successfully applied.

Recommended Response Action

Retrieve and view configuration operation results in the Lifecycle Log. For more information to retrieve the configuration results see the Lifecycle Controller Remote Services Users Guide. Identify the unsuccessful configuration operations. Modify the input data as appropriate for the component and retry the configuration operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS036

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to apply the configuration to the component.
Detailed Description: The configuration settings could not be applied to the component. This may indicate configuration changes since the last system inventory collection was completed.
Recommended Response Action: Retry the operation or try the attribute set operation for the component.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS037

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Component update initialization failure.
Detailed Description: Operation validation is unsuccessful. The command, target and operation data are all validated before an update is performed. If any of them are missing or incorrect the operation does not complete successfully.
Recommended Response Action: Enable the Collect System Inventory on Restart attribute using Lifecycle Controller and restart the system. Retry the operation after the system restarts.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS038

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Missing or corrupt configuration information.
Detailed Description: Unable to locate the configuration data associated with the job.
Recommended Response Action: Retry the operation. If this issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS039

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Verification of requested configuration changes failed.
Detailed Description: The requested configuration changes have not passed the component specific verification checks, and therefore the changes will not be applied.
Recommended Response Action: Check the scripts or related documentation and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS040

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The firmware update operation did not complete successfully.
Detailed Description: An operation to update the firmware of a component did not complete successfully.
Recommended Response Action: Check the Lifecycle Log for more details about the unsuccessful operation. Resolve the issue and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS041

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to apply some component configuration values.
Detailed Description: The configuration update is complete, however all of the values were not correctly applied.
Recommended Response Action: Check the Lifecycle Log for the values that were not set. Resolve the issues in the XML configuration input file and retry the operation. Alternatively, configure each of the attributes using the component service methods. For more information, see the Lifecycle Controller Users Guide.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS042

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Component configuration successfully completed.
Detailed Description: The requested component configuration successfully completed.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS043

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully exported Server Configuration Profile.
Detailed Description: The current configuration of the system components (BIOS, RAID, NIC, iDRAC, and so on) was written to a Server Configuration Profile and successfully copied to the specified location.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS044

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export one or more component configurations.
Detailed Description: Unable to collect the configuration information for one or more components. An internal error occurred while processing component information.
Recommended Response Action: Enable Collect System Inventory On Restart (CSIOR) using Lifecycle Controller and restart the system. Make sure that inventory collection is complete before retrying the operation. For more information, see the Lifecycle Controller Users Guide.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS045

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to copy the Server Configuration Profile to the network share.
Detailed Description: An error occurred while copying the Server Configuration Profile to the network share.
Recommended Response Action: If the file is being exported to an NFS share, make sure that it is accessible from iDRAC. If the file is being exported to a CIFS share, make sure that it is accessible from iDRAC by using share access credentials with the appropriate privileges. If the share is by using http or https protocol, make sure that you have correctly configured the share and it can be accessible by using iDRAC.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS046

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the Server Configuration Profile from the network share.
Detailed Description: An error occurred while copying the Server Configuration Profile from the network share.
Recommended Response Action: If the file is being copied from an NFS share, make sure that it is accessible from iDRAC. If the file is being copied from a CIFS share, make sure that it is accessible from iDRAC using the share credentials provided. Test the network share access using the Test Network Connection method. For more information, see the Lifecycle Controller Users Guide.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS047

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Input file for import configuration is not compliant with the configuration schema.
Detailed Description: The input file is not compliant with the system configuration schema.
Recommended Response Action: Make sure that the input file is compliant with the system configuration schema published on delltechcenter.com/lc in the LC profile Schema Guide.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS048

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Server Configuration Profile contains invalid characters, arg1 at line arg2.

Arguments

arg1 = character
arg2 = line

Detailed Description

The operation expected a valid profile that is compliant with the system configuration schema. However, the Server Configuration Profile does not contain valid profile content.

Recommended Response Action

View the file in any Web browser to check for invalid characters. Remove the invalid characters and make sure that the file is a valid XML and is compliant with the system configuration schema published on delltechcenter.com/lc in the LC profile Schema Guide.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS050

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Server Configuration Profile for import configuration is not compliant with schema nesting checks.
Detailed Description: The Server Configuration Profile for the import configuration operation is not compliant with schema nesting checks. Only RAID controllers can have nested Component nodes up to a maximum nesting depth of three.
Recommended Response Action: Make sure that the Server Configuration Profile is compliant with the system configuration schema published on delltechcenter.com/lc in the LC profile Schema Guide. Only RAID controllers can have nested Component nodes.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS051

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The system could not be shut down within the specified time.
Detailed Description: Sometimes, the operating system on the server may not allow a graceful shutdown or may not complete within the specified graceful shutdown timeout. This error indicates that the system could not be shutdown within the time specified. The default timeout value is 5 minutes and the maximum value allowed is 1 hour.
Recommended Response Action: Retry the operation with a longer specified graceful shutdown timeout or with the system shutdown option.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS052

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Analyzing iDRAC, System, or Lifecycle Controller configuration for changes to be applied.
Detailed Description: Configuration changes that do not require a system restart are currently being applied.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS053

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully imported and applied Server Configuration Profile.
Detailed Description: Configuration changes specified in the Server Configuration Profile were successfully applied.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS054

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No configuration changes requiring a system restart need to be applied.
Detailed Description: The current configuration for components that require staged configuration already match the configuration specified by the input file. A system restart to apply staged configuration is not required.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS055

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Import of Server Configuration Profile operation completed with errors.
Detailed Description: The configuration specified in the Server Configuration Profile was applied, but there were some errors. The Lifecycle Controller Log contains the details of the component configurations that did not complete successfully.
Recommended Response Action: Review the Lifecycle Controller Log and identify the configuration changes that did not complete successfully. Retry those changes in a separate operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS056

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Waiting for the system to shut down.
Detailed Description: Waiting for the system to shut down before applying configuration changes.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS057

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Exporting Server Configuration Profile.
Detailed Description: The current system configuration is being collected and the Server Configuration Profile is being generated.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS058

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Applying configuration changes.
Detailed Description: Running Lifecycle Controller Automated Task Execution application in Unified Extensible Firmware Interface (UEFI) environment to apply configuration changes.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS059

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Component configuration successfully changed.
Detailed Description: Configuration changes for the component identified by the Fully Qualified Device Descriptor (FQDD) were successfully applied.
Recommended Response Action: No response action is required. See Lifecycle Log for details.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS060

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Component configuration completed with errors.
Detailed Description: Some configuration changes for the component identified by the Fully Qualified Device Descriptor (FQDD) in the configuration job results were not successfully applied.
Recommended Response Action: Export the Lifecycle Log and identify the configuration changes that did not complete or retrieve the configuration results using the GetConfigResults() method. Retry those changes that did not complete in a separate import operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS061

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete component configuration.
Detailed Description: Some configuration changes for the component identified by the Fully Qualified Device Descriptor (FQDD) in the configuration job results were not successfully applied.
Recommended Response Action: Export the Lifecycle Log and identify the configuration changes that did not complete or retrieve the configuration results using the GetConfigResults() method. Retry those changes that did not complete in a separate import operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS062

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Input file for import configuration operation is invalid. The expected profile root element was not found.
Detailed Description: The input file for the import configuration operation does not contain a valid profile root element.
Recommended Response Action: Open the input file in any Web browser to check for invalid content before the expected root element. Correct the invalid content and make sure that the profile is compliant to the system configuration schema before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS063

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Input file for import configuration operation is invalid. The expected root element was not closed.
Detailed Description: The input file for the import configuration operation does not contain a closed root element.
Recommended Response Action: Open the input file in any Web browser to check for invalid content before the expected root element. Correct the invalid content and make sure that the profile is compliant to the system configuration schema before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS064

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Input file for import configuration operation is invalid at line arg1.

Arguments

arg1 = line

Detailed Description

The input file for the import configuration operation contains invalid XML data at the line specified.

Recommended Response Action

Open the input file in any Web browser to check for invalid content before the expected root element. Correct the invalid content and make sure that the XML file is compliant to the system configuration schema before retrying the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS065

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Input file for import configuration operation cannot be found or opened.
Detailed Description: An internal error occurred opening the input configuration XML file. An iDRAC reset is required.
Recommended Response Action: Reset iDRAC and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS066

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No changes detected for iDRAC, System, or Lifecycle Controller configuration.
Detailed Description: No iDRAC, System, or Lifecycle Controller configuration changes were applied. The settings specified in the system configuration XML input file match the current configuration for these components.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS067

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete application of configuration profile values.
Detailed Description: Some or all configuration actions during the import of configuration profile operation did not complete successfully. The configuration action details are logged into the Lifecycle Log.
Recommended Response Action: Export the Lifecycle Log and identify the configuration changes that did not successfully complete. Resolve any issues with the configuration profile content and retry the import operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS068

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Configuration changes that require system reboot were not applied.
Detailed Description: Some configuration changes that require system reboot were not applied because the values specified in the input XML file are incorrect.
Recommended Response Action: Use the GetConfigResults() method to get the configuration job results or export the Lifecycle Log and review the configuration job results to identify the errors. Make changes to the input XML to correct the errors. Retry the import operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS069

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No changes were applied since the current component configuration matched the requested configuration.
Detailed Description: The settings specified in the system configuration XML file match the current configuration for all components.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS070

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Configuration changes that require system reboot were not applied.
Detailed Description: The configuration changes that require system reboot into the UEFI environment on the system did not complete for all components.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS071

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Server Configuration Profile export operation timed-out.
Detailed Description: The export of Server Configuration Profile did not complete because the operation took too long.
Recommended Response Action: Make sure the Collect System Inventory On Restart (CSIOR) Lifecycle Controller setting is enabled and reboot the system. Retry the operation after CSIOR has completed. If the problem persists, reset iDRAC by pressing the System ID button for at least 15 seconds and retry the operation after iDRAC has fully restarted.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS072

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Server Configuration Profile import operation timed-out.
Detailed Description: The import of Server Configuration Profile did not complete as the operation took too long.
Recommended Response Action: Review the state of the host server and ensure there is no user input required that has disrupted the SCP workflow. There could be one or more reasons for server to halt at POST.1) The BIOS ErrPrompt setting being Enabled can require manual interaction during POST.2) The iDRAC ServerBoot.1#FirstBootDevice being set to BIOS will boot the system to the BIOS F2 menu requiring manual interaction.3) Review any error listed in POST and take appropriate action mentioned on the screen.If the host booted completed but the operation timed-out, then review the LCL before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS073

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to apply changes that require system reboot because the Lifecycle Controller State setting is disabled in the Server Configuration Profile.
Detailed Description: The import of Server Configuration Profile operation completed with errors because the Lifecycle Controller State was disabled in the input profile. Configuration changes requiring a system reboot were not applied.
Recommended Response Action: Enable the Lifecycle Controller State setting and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS074

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to apply configuration changes because another configuration job is in progress.
Detailed Description: Unable to apply configuration changes because another configuration job is in progress.
Recommended Response Action: Wait until the current configuration job is complete and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS075

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the import operation because the specified file does not exist on the remote share.
Detailed Description: Unable to perform the import operation because the specified file does not exist on the remote share.
Recommended Response Action: Make sure the import configuration file exists on the remote share before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS076

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid or unsupported component specified in the input configuration profile.
Detailed Description: The configuration profile contains a component node that is not supported.
Recommended Response Action: Make sure the input configuration profile only specifies supported component. Check the import operation job configuration results for the unsupported profile node.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS077

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the preview operation because the specified file does not exist on the remote share.
Detailed Description: Unable to perform the preview operation because the specified system configuration XML file does not exist on the remote share.
Recommended Response Action: Make sure the configuration XML file to be previewed exists on the remote share before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS078

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the Server Configuration Profile from the network share for preview.
Detailed Description: Unable to retrieve the Server Configuration Profile from the network share for the requested preview operation. This may be due to issues with network accessibility.
Recommended Response Action: If the configuration profile is on an NFS share, make sure that the network share is accessible from iDRAC. If the configuration profile is on a CIFS share, make sure that the network share is accessible from iDRAC using the share credentials specified. Test the network share access using the Test Network Connection method. For more information, see the Lifecycle Controller Users Guide.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS079

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Preview operation indicates the input file for Server Configuration Profile is not compliant with the configuration profile schema.
Detailed Description: The Preview operation indicates the input file for Server Configuration Profile is not compliant with the configuration profile schema.
Recommended Response Action: Make sure that the input file is compliant with the system configuration XML schema published on www.delltechcenter.com/lc.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS080

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Preview of Server Configuration Profile import operation indicated that no configuration changes will be successful.
Detailed Description: Preview of Server Configuration Profile import operation indicates that no changes will be applied successfully. This is likely due to a mismatch between the actual target system components and component FQDDs specified in the configuration profile.
Recommended Response Action: Make sure that the input file is compliant with the system configuration schema published on www.delltechcenter.com/lc and contains valid FQDDs that represent actual components in the target system.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS081

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully previewed Server Configuration Profile import operation.
Detailed Description: Successfully previewed Server Configuration Profile import operation.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS082

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Completed the preview of Server Configuration Profile import operation. Some changes specified in the configuration profile will not be successfully applied in an import operation.
Detailed Description: The request to preview the Server Configuration Profile import operation completed. Some changes specified in the configuration profile will not be successfully applied in an import configuration profile operation.
Recommended Response Action: Identify the configuration changes that cannot be completed successfully by 1) Export the Lifecycle Log review the configuration results in the entries for the preview job or 2) Retrieve the preview operation configuration results using the GetConfigResults() method. Retry those changes that did not complete in a separate import operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS083

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export ePSA Diagnostics results because iDRAC internal storage could not be accessed.
Detailed Description: Unable to export ePSA Diagnostics results because iDRAC internal storage could not be accessed.
Recommended Response Action: Do the following: 1) Delete all jobs, 2) Reset iDRAC by pressing the System ID button for at least 15 seconds, and 3) Retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS084

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Export of ePSA Diagnostics results did not complete successfully because the iDRAC internal storage containing the results could not be accessed.
Detailed Description: Export of ePSA Diagnostics results did not complete successfully because the iDRAC internal storage containing the results could not be accessed.
Recommended Response Action: Do the following: 1) Delete all jobs, 2) Reset iDRAC by pressing the System ID button for at least 15 seconds, and 3) Retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS085

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully exported the ePSA Diagnostics results.
Detailed Description: Successfully exported ePSA Diagnostics results.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS086

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to copy the ePSA Diagnostics results file to the network share.
Detailed Description: Unable to copy the ePSA Diagnostics results file to the specified network share.
Recommended Response Action: If the results are being exported to an NFS share, make sure that the network share is accessible from iDRAC. If the results are being exported to a CIFS share, make sure that the network share is accessible from iDRAC using the specified share access credentials.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS087

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A system reboot will occur when the previewed configuration XML file is imported to the system.
Detailed Description: When the configuration XML file specified in the Preview operation is imported to the system, a system reboot will occur to apply the configuration changes.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS088

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Estimated time for applying configuration changes is arg1 seconds.

Arguments

arg1 = configuration time

Detailed Description

Applying the changes defined in the configuration XML file will take approximately the estimated time identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS089

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Preview of Server Configuration Profile is complete.
Detailed Description: The Preview operation of Server Configuration Profile is complete.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS090

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The configuration profile contains unsupported DOCTYPE tags.
Detailed Description: The configuration profile contains DOCTYPE tags which may contain injection security threats. The DOCTYPE tag is not supported in configuration profiles.
Recommended Response Action: Check the input XML file for DOCTYPE XML tags and remove them before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS091

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the method is not supported.
Detailed Description: Unable to complete the operation because the method is not supported.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS092

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC is collecting information about the server for a Tech Support Report.
Detailed Description: The iDRAC is collecting information about the server for a Tech Support Report.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS093

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC is exporting the Tech Support Report.
Detailed Description: The iDRAC is exporting the Tech Support Report to the specified destination.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS094

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC is unable to start the Tech Support Report job, because a report collection job is already running on the server.
Detailed Description: The Tech Support Report collection job could not be started, because a report collection job is already running on the server.
Recommended Response Action: Wait until the current Tech Support Report operation is complete and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS095

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to unmount an iDRAC internal storage partition.
Detailed Description: Unable to unmount an iDRAC internal storage partition.
Recommended Response Action: Retry the operation. If the issues persists, reset the iDRAC by pressing the System ID button for at least 15 seconds, and then retry the operation after the iDRAC has finished restarting.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS096

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the diagnostics operation because the required Dell Diagnostics firmware package is not installed.
Detailed Description: The required Dell Diagnostics firmware package is not installed or cannot be found in the iDRAC internal storage.
Recommended Response Action: Install the Dell 64bit uEFI Diagnostics firmware package, and then retry the operation. The Dell Diagnostics can be installed using the Dell 64bit uEFI Diagnostics Dell Update Package (DUP).
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS097

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The state of Lifecycle Controller is disabled by the configuration profile import operation.
Detailed Description: The Lifecycle Controller State has been set to disabled by the configuration profile import operation. Further changes to the system configuration require the Lifecycle Controller State to be enabled before the changes are processed.
Recommended Response Action: If further configuration changes are required for the system, the Lifecycle Controller State must be enabled prior to attempting the configuration change. To enable the Lifecycle Controller State, run the racadm command "racadm set LifecycleController.LCAttributes.LifecycleControllerState Enabled".
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS098

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A Remote Diagnostic (ePSA) job already exists.
Detailed Description: A Remote Diagnostic (ePSA) job already exists and only one job of this type can exist at a time.
Recommended Response Action: A response action is not required if the scheduled start time of the existing Remote Diagnostic (ePSA) job is ok. Else, delete the existing Diagnostics (ePSA) job and recreate another with an appropriate start time.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS099

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the diagnostics results because the results do not exist.
Detailed Description: The diagnostics results could not be exported because either the diagnostics tests were never run on the system or the results could not be found on the internal storage of the iDRAC.
Recommended Response Action: Run the RunEPSADiagnostics method to make sure that the diagnostics results are available, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS100

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to find an FQDD equivalent for the token arg1

Arguments

arg1 = token name

Detailed Description

A FQDD equivalent for the token name identified in the message cannot be found.

Recommended Response Action

Make sure that only valid FQDDs are entered as input to the Target parameter, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS1000

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System is turning on.
Detailed Description: System is turning on.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Trap/EventID: 8579
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Not Applicable

SYS1001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System is turning off.
Detailed Description: System is turning off.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Trap/EventID: 8579
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Not Applicable

SYS1002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System is performing a power cycle.
Detailed Description: System is performing a power cycle.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Trap/EventID: 8579
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Not Applicable

SYS1003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System CPU Resetting.
Detailed Description: System is performing a CPU reset because of system power off, power on or a warm reset like CTRL-ALT-DEL.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Trap/EventID: 8579
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Not Applicable

SYS1005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The server power action is initiated because arg1.

Arguments

arg1 = reason

Detailed Description

The server power action is initiated because of the reason identified in the message.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Trap/EventID

8579

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS1006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 operation has arg2.

Arguments

arg1 = operationName
arg2 = actionName

Detailed Description

The operation identified in the message has started or stopped.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Trap/EventID

8579

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS1007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 operation is completed arg2.

Arguments

arg1 = operationName
arg2 = operationStatus

Detailed Description

The operation identified in the message is completed.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Trap/EventID

8579

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS1008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to perform the arg1 because arg2.

Arguments

arg1 = operationName
arg2 = reason

Detailed Description

The operation cannot be performed because of the reason identified in the message.

Recommended Response Action

No response action is required based on the reason identified. If it is an internal error: 1) Rerun the command. 2) Reset the management controller and then run the command. If invalid parameter, then review and correct input value to rerun the command. If no authorization, then obtain the authorization necessary and run command.

Category

Audit (SYS = System Info)

Severity

Warning

Trap/EventID

8578

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS1009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A arg1 board replacement operation is detected.

Arguments

arg1 = boardName

Detailed Description

A board replacement operation is detected as identified in the message.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Trap/EventID

8579

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS101

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Server Administrator Data Manager service has started.
Detailed Description: The Server Administrator Data Manager service has started.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5008
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS1010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

System contents of arg1 is successfully restored.

Arguments

arg1 = componentName

Detailed Description

One or more platform system components were replaced. The previous system configuration contents were successfully restored.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Trap/EventID

8579

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS1011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to restore the arg1 on the server during arg2 replacement.

Arguments

arg1 = componentName
arg2 = boardName

Detailed Description

One or more components cannot be restored on the server when replacing the board identified in the message.

Recommended Response Action

Manually set attribute values for the failed component(s).

Category

Audit (SYS = System Info)

Severity

Warning

Trap/EventID

8578

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS1012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The previous system content has not been restored. After replacing the arg1 and restarting the server, N was selected to indicate that a system content restoration is not required.

Arguments

arg1 = board name

Detailed Description

The previous system content has not been restored. After replacing the board identified in the message, and then restarting the server, N was selected to indicate that a system content restoration is not required.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Trap/EventID

8579

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS1013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 arg2 operation is performed through the arg3.

Arguments

arg1 = componentName
arg2 = operationName
arg3 = source

Detailed Description

The power or reset operation is performed on the component.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Trap/EventID

8579

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, LCD, OS Log

Applicable Event or Alert Types

CMC—Not Applicable

SYS102

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Server Administrator Data Manager service has stopped.
Detailed Description: The Server Administrator Data manager service has stopped.
Recommended Response Action: Restart the Server Administrator Data Manager service.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5009
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS103

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Administrator has started.
Detailed Description: The Server Administrator has started.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5001
OMSA Trap ID: 5001
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS104

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Server Administrator is starting.
Detailed Description: The Server Administrator is starting.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5000
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS105

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to process the event: arg1 Date and time of event: arg2.

Arguments

arg1 = event
arg2 = date time

Detailed Description

The current software version is unable to process this event because of an internal error.

Recommended Response Action

Contact your service provider.

Category

System Health (SYS = System Info)

Severity

Warning

OMSA Event ID

5014

OMSA Trap ID

5014

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SYS106

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An unknown system control action was initiated by the user.
Detailed Description: An unknown system control action was initiated by the user.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS107

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A system reboot was initiated by the user.
Detailed Description: The user initiated a system reboot.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
OMSA Trap ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS108

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A system power off was initiated by the user.
Detailed Description: The user has initiated a system power off action.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
OMSA Trap ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS109

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A system power cycle was initiated by the user.
Detailed Description: The user has initiated a system power cycle action.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
OMSA Trap ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS110

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The actions Shutdown OS First and Reboot System were initiated by the user.
Detailed Description: The actions will shut down the operating system and then reboot the system.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
OMSA Trap ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS111

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The actions Shutdown OS First and Power Off System were initiated by the user.
Detailed Description: The actions will shut down the operating system and then the system.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
OMSA Trap ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS112

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The actions Shutdown OS First and Power Cycle System were initiated by the user.
Detailed Description: The actions will shut down the operating system and then power cycle the system.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
OMSA Trap ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS113

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An invalid action was requested by the user.
Detailed Description: An invalid action was requested by the user.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
OMSA Event ID: 5007
OMSA Trap ID: 5007
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS114

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The IPMI status for the interface: arg1, Baseboard Management Controller (BMC): arg2, Sensor Data Records (SDR): arg3, System Event Log (SEL): arg4.

Arguments

arg1 = interface
arg2 = BMC
arg3 = SDR
arg4 = SEL

Detailed Description

IPMI is supported for identified interface, Baseboard Management Controller (BMC), Sensor Data Records (SDR), and System Event Log (SEL).

Recommended Response Action

If any status is not present, power cycle the system, and apply the latest firmware update packages for Lifecycle Controller and iDRAC.

Category

System Health (SYS = System Info)

Severity

Informational

OMSA Event ID

5012

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SYS115

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The power cord sensor is non-functional.
Detailed Description: The power cord sensor becomes non-functional because of one of the following reasons: 1) The power cable may not be connected properly or disconnected. 2) The power cord sensor in the power supply unit has failed. However, the power supply unit may still function. 3) There is an input power failure.
Recommended Response Action: Do of the following to resolve the issue: 1) Reconnect the power cord to the power supply unit. 2) Replace the power supply unit that has the failed power cord sensor, with a new power supply unit. 3) Make sure that the input power supply is restored.
Category: System Health (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS116

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to determine the status of the power cord.
Detailed Description: The status of the power cord cannot be determined because of one of the following reasons: 1) The power cable may not be connected properly or disconnected. 2) The power cord sensor in the power supply unit has failed. However, the power supply unit may still function. 3) There is an input power failure.
Recommended Response Action: Do of the following to resolve the issue: 1) Reconnect the power cord to the power supply unit. 2) Replace the power supply unit that has the failed power cord sensor, with a new power supply unit. 3) Make sure that the input power supply is restored.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS117

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The input power supply is restored.
Detailed Description: The input power supply is restored to the system.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS118

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The input power supply is not available.
Detailed Description: The input power supply is not available because of one of the following reasons: 1) The power cable may not be connected properly or disconnected. 2) There is an input power failure.
Recommended Response Action: Do of the following to resolve the issue: 1) Reconnect the power cord to the power supply unit. 2) Make sure that the input power supply is restored.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS119

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to expose the OS Collector to the server OS.
Detailed Description: The OS collector cannot be exposed to the host server because of communication issues between the iDRAC and server OS.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, restart the iDRAC and server OS.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS120

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the OS Collector is taking too much time. The operation is cancelled.
Detailed Description: The OS Collector application did not complete its task within the maximum allowed time and the operation is cancelled. This may be because the server OS is not supported by the OS Collector application and the application is unable to function correctly.
Recommended Response Action: Do the following: 1) Make sure that the OS Collector application supports the OS installed on the server. If the OS is not supported, the OS Collector may not function correctly. 2) Reinstall the latest OS Collector on the iDRAC, and then retry the operation. To install the OS Collector using the iDRAC Web UI, get the latest OC Collector update package and then select the Update and Rollback link from the iDRAC Web UI home page and upload the install package. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS121

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation to collect OS and Application Data was cancelled using iDRAC Web UI.
Detailed Description: The operation to collect OS and Application Data was cancelled using iDRAC Web UI.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS122

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: The operation to collect OS and Application Data is successfully completed.
Detailed Description: The operation to collect OS and Application Data is successfully completed.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS123

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: An unexpected issue has been encountered.
Detailed Description: An unexpected issue has occurred. This could be because the application encountered an unexpected exception or was terminated by a user. This issue could also be because the application was running in an unsupported OS.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the OS Collector on the iDRAC to the most recent version available, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS124

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: The OS Collector application does not support execution in the OS installed on the server.
Detailed Description: The OS and Application data collection by the OS Collector application is unable to execute on the OS installed on the server because the OS is not supported.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS125

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to communicate with WMI services.
Detailed Description: The OS Collector application is unable to communicate with the WMI service. This may be because the user context the application is running in does not have appropriate access privileges or firewall/security settings are preventing retrieving registry and software data from WMI.
Recommended Response Action: Do the following: 1) Make sure the user context the OS Collector application is running in has the appropriate privileges to access WMI. Make sure that firewall or security settings are set to allow access and retry the operation. 2) If the issue persists, restart the WMI service and retry the operation. 3) If the issue continues to persists, restart the server OS and retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS126

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to collect Application Data.
Detailed Description: Application data source was not found. An issue occurred while collecting Application Data because of an unknown exception.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the latest OS Collector on the iDRAC, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS127

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to collect OS log data
Detailed Description: OS log data was not collected. An issue occurred while collecting OS log data because of an unknown exception.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the latest OS Collector on the iDRAC, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS128

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to generate a zip archive of the OS and Application Data report.
Detailed Description: Unable to generate a zip archive of the OS and Application Data report.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the latest OS Collector on the iDRAC, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS129

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to complete XML transform on the data collected.
Detailed Description: Unable to complete XML transform on the data collected because the collected data is in an unexpected format.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the latest OS Collector on the iDRAC, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS130

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to create filename for zip archive.
Detailed Description: Unable to create the final zip archive name because the Service Tag and time stamp could not be retrieved from OS interfaces.
Recommended Response Action: Do the following: 1) On Windows, restart the WMI service and retry the operation, 2) Restart the OS and retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS131

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to communicate with the OS IPMI service.
Detailed Description: Unable to communicate with the OS IPMI service because the service is not running.
Recommended Response Action: For more information about checking whether the IPMI service is running, see the iDRAC8 Users Guide.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS132

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Unable to communicate with OS Collector IPMI library.
Detailed Description: An issue occurred while loading the OS Collector IPMI library. This may be because the OS collector binary images are not valid and need to be re-installed.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the latest OS Collector on the iDRAC, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS133

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: IPMI session error.
Detailed Description: An issue was encountered while creating an IPMI session.
Recommended Response Action: Restart the WMI service and retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS134

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: Zip archive size exceeded the limit.
Detailed Description: The report size is more than the 30MB allowed size which will cause a truncated, partial report to be generated.
Recommended Response Action: Remove older log entries so that the final zip archive size can be reduced.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS135

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Collector: The user context the OS Collector is being run in does not have the necessary privileges for running the application successfully.
Detailed Description: The user context the OS Collector is being run in does not have the necessary privileges for running the application successfully.
Recommended Response Action: Run the OS Collector application as administrator or as a user added to admin group or domain administrator or Local administrator.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS136

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An issue was encountered while communicating with iDRAC Service Module (iSM) present on the operating system.
Detailed Description: An issue was encountered while communicating with iDRAC Service Module (iSM) present on the operating system.
Recommended Response Action: Do the following: 1) Restart the iDRAC Module Service on the OS and retry the operation. 2) Stop iDRAC Service Module Service on the OS and try manually executing the OS Collector application .
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS137

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the collection of OS and Application Data because the Lifecycle Controller is not enabled.
Detailed Description: Unable to start the collection of OS and Application Data because the Lifecycle Controller is not enabled.
Recommended Response Action: Enable the Lifecycle Controller by pressing F2 during server startup and select iDRAC Settings > Lifecycle Controller and then enable the Lifecycle Controller. Retry the operation after the server has restarted.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS138

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the collection of OS and Application Data because the server is turned off.
Detailed Description: Unable to start the collection of OS and Application Data because the server OS is turned off.
Recommended Response Action: Turn on the server and wait until the OS finishes booting, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS139

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the collection of OS and Application Data because the server is in POST and has not finished startup.
Detailed Description: Unable to start the collection of OS and Application Data because the server is in POST and has not finished startup.
Recommended Response Action: Retry the operation after the server has finished starting and POST has completed.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS140

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the collection of OS and Application Data because the iDRAC Service Module (iSM) is not running in the server OS.
Detailed Description: Unable to start the collection of OS and Application Data because the iDRAC Service Module (iSM) is not running in the server OS.
Recommended Response Action: Enable and start the iDRAC Service Module (iSM) from within the server OS and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS141

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle Controller data is deleted.
Detailed Description: The Lifecycle Controller data is deleted because of a System Erase operation.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS142

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The OS driver pack is deleted.
Detailed Description: The OS driver pack is deleted because of a System Erase operation.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS143

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: ePSA Diagnostics are deleted.
Detailed Description: ePSA Diagnostics are deleted because of a System Erase operation.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS144

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Starting controller hardware cache data erase operations.
Detailed Description: Starting controller hardware cache data erase operations because of a System Erase operation request.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS145

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: vFlash SD Card data is deleted.
Detailed Description: vFlash SD Card data is deleted because of a System Erase operation.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS146

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Starting cryptographic erase-capable drive erase operations.
Detailed Description: Starting cryptographic erase-capable drive erase operations because of a System Erase operation request.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS147

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Starting non-cryptographic erase-capable drive erase operations.
Detailed Description: Starting non-cryptographic erase-capable drives erase operations because of a System Erase operation request.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS148

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: BIOS is configured to reset to defaults on next system restart.
Detailed Description: The BIOS is configured to reset to defaults on the next system restart because of a System Erase operation.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS149

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The process of resetting iDRAC to default settings is initiated.
Detailed Description: Initiating iDRAC reset to defaults operation because of a System Erase operation. The iDRAC will restart after firmware default values are restored.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS150

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Starting System Erase operation. Job ID: arg1

Arguments

arg1 = job ID

Detailed Description

A System Erase job with the job ID identified in the message is initiated.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS151

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Completed System Erase Job ID: arg1

Arguments

arg1 = job ID

Detailed Description

A System Erase job with the job ID identified in the message is completed.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS152

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Erase operations for some System Erase tasks did not complete successfully.
Detailed Description: Some of the requested storage component erase tasks were not successful. Retrying the System Erase operation may be required.
Recommended Response Action: Retry the System Erase operation. To retry the System Erase operation using the Lifecycle Controller utility, restart the server and when the company logo is displayed, press . Select Hardware Configuration > Retire or Repurpose System, check appropriate storage options, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS153

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Deleting hardware cache data for controller: arg1.

Arguments

arg1 = device name

Detailed Description

The non-volatile cache of the controller identified in the message is being erased.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS154

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Initiating cryptographic erase operation on secure erase-capable drives for controller: arg1.

Arguments

arg1 = device name

Detailed Description

Initiating cryptographic erase operation on secure erase-capable drives for the controller identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS155

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Initiating clear operation on non-cryptographic erase-capable drives for controller: arg1.

Arguments

arg1 = device name

Detailed Description

Initiating clear operation on non-cryptographic erase-capable drives for the controller identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS156

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Erase operations for System Erase tasks successfully completed.
Detailed Description: The requested component erase tasks of the System Erase operation is successfully completed.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS157

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to successfully complete requested System Erase tasks.
Detailed Description: Unable to successfully complete requested options of the System Erase operation. Retrying the System Erase operation may be required.
Recommended Response Action: Retry the System Erase operation. To retry the System Erase operation using the Lifecycle Controller utility, restart the server and when the company logo is displayed, press . Select Hardware Configuration > Retire or Repurpose System, check appropriate options, and then retry the operation. Also disable "F1/F2 Prompt on Error" in BIOS settings for System Erase operation to continue without intervention.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS158

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Hardware cache erase is unsuccessful.
Detailed Description: Unable to erase hardware caches during the System Erase operation.
Recommended Response Action: Retry the System Erase operation with only the hardware cache erase option selected.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS159

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: vFlash SD Card erase unsuccessful.
Detailed Description: The vFlash SD Card erase operation was unsuccessful. This may be because the SD card is not enable, not licensed or not initialized.
Recommended Response Action: Make sure the vFlash SD Card is enabled, licensed and initialized, and then retry the System Erase operation with only the vFlash option selected.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS160

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Lifecycle Controller logs are cleared.
Detailed Description: The Lifecycle Controller log data deleted as part of a System Erase operation. All previously stored information is no longer available.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS161

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: SupportAssist related non-volatile storage deleted.
Detailed Description: The SupportAssist related data has been deleted from iDRAC non-volatile storage.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS162

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Turning on the server to perform System Erase tasks.
Detailed Description: The server will be turned on to enter UEFI System Services Manager (SSM). The storage-related erase operations selected, if any, will be processed by SSM.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS163

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC is restarting to complete the System Erase operation. Do not restart server until the iDRAC restarts.
Detailed Description: The iDRAC environment has changed and the iDRAC must be restarted to apply the changes requested. Normal operation will return after the restart has completed. One exception is, the iDRAC has been reset to its default settings. In this case additional setup is required to use the iDRAC. For more information, see the iDRAC Users Guide.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS164

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Access to Lifecycle Controller internal storage was not acquired.
Detailed Description: The System Erase operation attempted to access Lifecycle Controller internal storage that is already being accessed by another function. Exclusive access to the internal storage is required for the System Erase operation. The System Erase operation attempts Lifecycle Controller internal storage access for 10 minutes. After the timeout the current job completes with an unsuccessful status.
Recommended Response Action: Check the server and make sure that it is not in BIOS POST startup processing or stopped in the POST phase of startup. The server can also be stopped during POST because the is pressed or Option ROM setup utilities are being used. After the BIOS startup has completed, retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS165

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: One or more Tech Support Report data collection options selected did not complete successfully.
Detailed Description: One or more Tech Support Report data collection options selected did not complete successfully.
Recommended Response Action: Look at the Lifecycle Log for exception messages and resolve the issues described.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS166

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The collection of OS and Application Data did not start within the allocated time.
Detailed Description: The collection of OS and Application Data did not start within the allocated time.
Recommended Response Action: Do one of the following: 1) Retry the operation. 2) Make sure the OS does not have any firewall setting to block USB device enumeration, and then retry the operation. 3) Make sure the OS is not configured to attach USB devices as read-only, and then retry the operation. 4) Make sure the OS is supported by the OS Collector application. 5) Reinstall the latest OS Collector on the iDRAC, and then retry the operation. 6) For more information about the collection of OS and application data, see the iDRAC8 Users Guide.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS167

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: TTY Log data export did not complete within the allocated time.
Detailed Description: The TTY Log data export did not complete within the allocated time. Currently the maximum allocated time is 20 minutes.
Recommended Response Action: Reset the iDRAC and retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS168

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the System Erase job because another operation is in progress.
Detailed Description: The requested System Erase job cannot complete because there was another job or System Services task already in progress.
Recommended Response Action: Wait for the job or System Services task in progress to complete before initiating a System Erase job.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS169

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Service Module installed on the operating system is not up to date and does not support the Technical Support Report feature.
Detailed Description: The iDRAC Service Module installed on the operating system is not up to date and does not support the Technical Support Report.
Recommended Response Action: Make sure the operating system (OS) is a supported OS for the Technical Support Report feature and the latest iDRAC Service Module software is installed on the OS.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS170

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SHA256 Hash value and the clear text value for an iDRAC user password cannot be entered together.
Detailed Description: The SHA256 Hash value and the clear text value for an iDRAC user password cannot be used at the same time for a password configuration operation.
Recommended Response Action: Make sure that the user password is configured using either the clear text or the SHA256 Hash, but not both.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS171

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to successfully complete the import operation because not all hash password values have been entered.
Detailed Description: The import operation cannot be completed successfully because the SHA1v3Key and the MD5V3Key values must both be supplied.
Recommended Response Action: The SHA1v3Key and the MD5V3Key values must be entered together for an import operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS172

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A Remote Diagnostic operation has been interrupted.
Detailed Description: A Remote Diagnostic operation has been interrupted because the server was restarted during the operation.
Recommended Response Action: Make sure that there are no diagnostic operations in progress before restarting the server or wait for the Remote Diagnostic operation to complete.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS173

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the TTY Log because another operation is in progress on the RAID controller.
Detailed Description: The TTY Log cannot be retrieved because another operation is in progress on the RAID controller.
Recommended Response Action: Do the following: 1) View the job queue and make sure all jobs are in a completed state. 2) Retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS174

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to access network share for exporting Tech Support Report (TSR).
Detailed Description: The Tech Support Report (TSR) cannot be exported because of an issue while connecting to the network share using the provided credentials or other network share parameters.
Recommended Response Action: Make sure the entered sharetype, sharename, IP address, username and password are valid and retry the operation. The network share connectivity can be tested by using the Test Network Connection feature of the iDRAC.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS175

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to find a device configuration for the FQDD entered.
Detailed Description: Selective Export / Import could not find any matches for the FQDDs specified.
Recommended Response Action: Make sure that only valid FQDDs are entered as input to the Target parameter, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS176

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Service Module related data have been deleted from iDRAC non-volatile storage.
Detailed Description: The iDRAC Service Module related data have been deleted from iDRAC non-volatile storage.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS177

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: There was an issue retrieving Hardware data.
Detailed Description: There was an issue retrieving Hardware data from the iDRAC internal storage. This may be because Collect System Inventory on Restart (CSIOR) feature is disabled and has never executed or the iDRAC Remote Services API status may not be in the Ready state.
Recommended Response Action: Make sure the Collect System Inventory on Restart (CSIOR) is enabled and has run at least once before retrying this operation. For remote web services API access, make sure the GetRemoteServicesAPIStatus method returns Ready status before trying this operation. If the issue persists, reset iDRAC and retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS178

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve TTY log data because no storage controllers are detected in the server.
Detailed Description: Unable to retrieve TTY log data because no storage controllers are detected in the server.
Recommended Response Action: Make sure that at least one storage controller is present in the server, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS179

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export TTY log data because the storage controller present in the server does not support the feature.
Detailed Description: Unable to export TTY log data because the storage controller present in the server does not support the feature.
Recommended Response Action: Make sure that at least one storage controller is present in the server that supports the TTY log feature, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS180

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

There was an issue encountered when attempted to export TTY Log data for the storage controller arg1.

Arguments

arg1 = controller name

Detailed Description

The TTY log data of the storage controller identified in the message cannot be exported because an issue was encountered while communicating with the controller.

Recommended Response Action

While exporting the TTY log, make sure that the server is not in BIOS POST, and then retry the operation. Use GetRemoteServicesAPIStatus() invoke method and check for output parameter RTStatus and ensure it shows 0 (ready status) and then retry the operation. If the issue persists, reset iDRAC, and retry the operation.

Category

System Health (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS181

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to collect OS and Application Data because the OS Collector is not installed on the iDRAC.
Detailed Description: The collect OS and Application Data operation cannot be completed because the OS Collector is not installed on the iDRAC.
Recommended Response Action: Install OS Collector on the iDRAC and retry the operation. To install the OS Collector using the iDRAC Web UI, get the latest OC Collector update package and then select the Update and Rollback link from the iDRAC Web UI home page and upload the install package.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS182

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to collect OS and Application Data because another Lifecycle Controller operation is currently in progress.
Detailed Description: Collecting OS and Application Data cannot be completed because Lifecycle Controller is used by another operation.
Recommended Response Action: Make sure all other Lifecycle Controller operations are finished and retry the operation. Using the iDRAC Web UI, select Server > Job Queue, check the job queue for unfinished jobs and wait for the jobs to finish before retrying the operation. Also, check whether there are update packages being executed in the server OS and wait for these operations to finish before retrying the operation. For remote web services API access, make sure that the GetRemoteServicesAPIStatus method returns Ready status, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS183

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to allocate memory because of insufficient storage space in iDRAC.
Detailed Description: The memory cannot be allocated because of insufficient storage space in iDRAC.
Recommended Response Action: Reset iDRAC and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS184

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to compute the checksum because OS Collector files are not readable.
Detailed Description: The checksum cannot be computed because OS Collector files are not readable.
Recommended Response Action: Reinstall the OS Collector in the iDRAC and retry the operation. To install the OS Collector using the iDRAC Web UI, get the latest OC Collector update package and then select the Update and Rollback link from the iDRAC Web UI home page and upload the install package. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS185

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Tech Support Report job has been cancelled.
Detailed Description: The Tech Support Report job that was running has been cancelled by user request.
Recommended Response Action: To start another Tech Support Report job, wait until the current job that is being cancelled completes and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS186

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the collection of TTY log data because the server is turned off.
Detailed Description: Unable to start the collection of TTY log data because the server OS is turned off.
Recommended Response Action: Turn on the server and wait until the OS finishes booting, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS187

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the collection of TTY log data because the server is in POST and has not finished startup.
Detailed Description: Unable to start the collection of TTY log data because the server is in POST and has not finished startup.
Recommended Response Action: Retry the operation after the server has finished starting and POST has completed.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS188

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the import operation because the specified file has a file size of zero, which is not valid.
Detailed Description: Unable to perform the import operation because the specified file has a file size of zero, which is not valid.
Recommended Response Action: Make sure the import configuration file is valid before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS189

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Cached OS and Application Data is not available in the iDRAC.
Detailed Description: There is no cached copy of OS and Application data in the iDRAC flash storage.
Recommended Response Action: Collect the OS and Application Data either manually or automatically using the iDRAC Services Module (ISM) tools and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS190

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to collect the operating system (OS)-related data because the iDRAC Service Module (iSM) installed on the server does not support this feature on the version of Operating System installed.
Detailed Description: The OS-related data cannot be collected because the iDRAC Service Module (iSM) installed on the server does not support this feature on the version of Operating System installed.
Recommended Response Action: Install a iDRAC Service Module (ISM) supported OS, and then retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS191

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Importing Server Configuration Profile.
Detailed Description: The provided Server Configuration Profile is being applied to the system. The host may reboot to apply all changes.
Recommended Response Action: No response action is required. Use the GetConfigResults() method to get the configuration job results or export the Lifecycle Log to review the configuration job results.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS192

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Previewing Server Configuration Profile.
Detailed Description: The provided Server Configuration Profile is being previewed on the system. No configuration changes will be applied.
Recommended Response Action: No response action is required. Use the GetConfigResults() method to get the preview job results or export the Lifecycle Log to review the preview job results.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS193

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A configuration change is detected for component: arg1.

Arguments

arg1 = component identifier

Detailed Description

A configuration change is detected in the component identified in the message.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS194

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Collection of System Inventory successfully completed.
Detailed Description: The Collection of System Inventory successfully completed by Lifecycle Controller firmware.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS195

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The OEM ID module is successfully installed.
Detailed Description: The OEM ID Module installation process completed with no errors.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS196

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The OEM ID module is installed but with some errors. arg1

Arguments

arg1 = Error Code

Detailed Description

The OEM ID module installation process tried to apply all settings and branding information, but had issues during installation.

Recommended Response Action

Check the Lifecycle Log report to analyze the issue. Review settings and branding information that the ID module configured, resolve the issue, and then retry the installation process.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS197

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to install the OEM ID module because of some issues. arg1

Arguments

arg1 = Error Code

Detailed Description

The OEM ID module cannot be installed because of some issues.

Recommended Response Action

Check the Lifecycle Log report to analyze the issue, resolve the issue, and then retry the installation process.

Category

Configuration (SYS = System Info)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS198

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to communicate with internal iDRAC memory.
Detailed Description: An internal iDRAC memory component is unresponsive.
Recommended Response Action: The iDRAC requires an AC power cycle. Do the following: 1) Determine a time that the AC power can be removed and then reapplied to the server. 2) Save data and perform an AC power cycle.
Category: System Health (SYS = System Info)
Severity: Critical
Trap/EventID: 2433
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, LCD, OS Log
Applicable Event or Alert Types: CMC—Not Applicable

SYS199

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The state of Lifecycle Controller is successfully changed to "disabled", but other attributes specified in the Server Configuration Profile (SCP) profile are not changed.
Detailed Description: The state of Lifecycle Controller is successfully changed to "disabled", but other attributes are not set. When the LifecycleControllerState attribute is set to disabled in the SCP profile, other attributes settings in the SCP profile are not applied.
Recommended Response Action: The Lifecycle Controller state must be "enabled" before performing the import SCP operation and the LifecycleControllerState attribute should not be set to disabled in the SCP profile while attempting to configure other attribute settings. To set LifecycleControllerState attribute to enabled using the RACADM command line utility, type "racadm set lifecyclecontroller.LCAttributes.LifecycleControllerState Enabled".
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS200

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The job with arg1 is successfully run and completed.

Arguments

arg1 = job ID

Detailed Description

The job identified in the message is successfully run and completed.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS201

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The disk erase operation on the drive arg1 successfully completed.

Arguments

arg1 = FQDD

Detailed Description

The disk erase operation is successfully completed on the drive identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS202

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the disk erase operation on the drive arg1.

Arguments

arg1 = drive identifier FQDD

Detailed Description

The disk erase operation cannot be completed on the drive identified in the message.

Recommended Response Action

Do the following: 1) Retry the System Erase operation. To retry the System Erase operation by using the Lifecycle Controller utility, restart the server. When the company logo is displayed, press F10. Select Hardware Configuration > Retire or Repurpose System, Select the appropriate options under Storage & Physical Disks, and then retry the operation. 2) If the issue persists, erase the drive manually.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS203

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The state of Lifecycle Controller can be set to only either Enabled or Disabled.
Detailed Description: The state of Lifecycle Controller can be set to only either Enabled or Disabled.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS204

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the drive erase operation because compatible drives are not found.
Detailed Description: The drive erase operation cannot be performed because compatible drives are not found.
Recommended Response Action: Make sure that the drive supports the erase operation by running the RACADM command at the Command Line Interface (CLI): racadm storage get pdisks -o. The "SystemEraseCapability" field must indicate "SecureErasePD" or "OverwritePD".
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS205

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to perform the drive erase operation for arg1 because the drive is part of a configuration that has both internal and external drives.

Arguments

arg1 = Drive FQDD

Detailed Description

The drive erase operation cannot be performed on the drive identified in the message because the drive is part of a configuration that has both internal and external drives.

Recommended Response Action

Delete the mixed configuration that the drive is part of by running the RACADM command at the command line prompt: "racadm storage deletevd:". Then perform the disk erase operation for the drive.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS206

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the drive erase operation on drives with no Secure Erase capability.
Detailed Description: Unable to perform the drive erase operation on drives with no Secure Erase capability.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS207

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the drive erase operation on external drives.
Detailed Description: Unable to perform the drive erase operation on external drives.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS208

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the provided SSH public key value is invalid.
Detailed Description: Unable to complete the operation because the provided SSH public key value is invalid.
Recommended Response Action: Enter a valid SSH public key and retry the operation. For information about valid public keys, see the Lifecycle Controller Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS209

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the given SSH Public Key size is less than the required minimum size of arg1 bits.

Arguments

arg1 = size

Detailed Description

The upload operation cannot be completed because the given SSH Public Key size is less than the required minimum size identified in the message.

Recommended Response Action

Retry the operation with an SSH Public Key with supported key size.

Category

Configuration (SYS = System Info)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS225

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the job arg1 successfully because of the issues listed in the Lifecycle Controller log files.

Arguments

arg1 = job ID

Detailed Description

The job identified in the message cannot be successfully completed because of the issues listed in the Lifecycle Controller log files.

Recommended Response Action

Verify the reason for the unsuccessful completion of the job by inspecting the Lifecycle Log entries related to the job. Correct the underlying cause of the unsuccessful completion and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS226

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of the reason described by the code arg2 sent by the HTTP remote host server.

Arguments

arg1 = filename
arg2 = http response code

Detailed Description

The file cannot be transferred because of the reason described by the code identified in the message. For every unsuccessful file transfer, the HTTP remote host server returns an error code, where each code has a description about the reason for failure.

Recommended Response Action

View the HTTP remote host server documentation to resolve the issue. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS227

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of the reason described by the code arg2 sent by the proxy server.

Arguments

arg1 = filename
arg2 = code

Detailed Description

The file cannot be transferred because of the reason described by the code identified in the message. For every unsuccessful file transfer, the proxy server returns an error code, where each code has a description about the reason for failure.

Recommended Response Action

View the proxy server documentation to resolve the issue. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS228

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The file, arg1, is successfully transferred.

Arguments

arg1 = filename

Detailed Description

The file is successfully transferred.

Recommended Response Action

No response action required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS229

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer file, arg1, because of some unknown reasons.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of some unknown reasons.

Recommended Response Action

Make sure that correct file transfer parameters are set, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS230

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported protocol value, arg2.

Arguments

arg1 = filename
arg2 = bad protocol

Detailed Description

The file cannot be transferred because of an unsupported protocol value.

Recommended Response Action

Make sure that the correct protocol value is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS231

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported source file path value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an unsupported source file path value.

Recommended Response Action

Make sure that the correct source file path is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS232

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported destination file path value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an unsupported destination file path value.

Recommended Response Action

Make sure that the correct destination file path value is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS233

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer the file, arg1, because of an unsupported hostname value, arg2.

Arguments

arg1 = file name
arg2 = bad hostname

Detailed Description

The file identified in the message cannot be transferred because of an unsupported hostname value.

Recommended Response Action

Make sure that the correct hostname value is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS234

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported port number value, arg2.

Arguments

arg1 = filename
arg2 = bad port number

Detailed Description

The file cannot be transferred because of an unsupported port number value.

Recommended Response Action

Make sure that the correct port number value is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS235

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported workgroup value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an unsupported port number value.

Recommended Response Action

Make sure that the correct workgroup value is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS236

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported username value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an unsupported username value.

Recommended Response Action

Make sure that the correct username value is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS237

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an incorrect password value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an incorrect password value.

Recommended Response Action

Make sure that the correct password value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS238

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an incorrect file path value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an incorrect file path value.

Recommended Response Action

Make sure that the correct file path value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS239

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported share name value, arg2.

Arguments

arg1 = filename
arg2 = bad share name

Detailed Description

The file cannot be transferred because of an unsupported share name value.

Recommended Response Action

Make sure that the correct share name value is used, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS240

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported mount-point path value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an unsupported mount-point path value.

Recommended Response Action

Make sure that the correct mount-point path value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS241

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported proxy type value, arg2.

Arguments

arg1 = filename
arg2 = bad proxy type

Detailed Description

The file cannot be transferred because of an unsupported proxy type value.

Recommended Response Action

Make sure that the correct proxy type value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS242

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported proxy hostname value, arg2.

Arguments

arg1 = filename
arg2 = bad hostname

Detailed Description

The file cannot be transferred because of an unsupported proxy hostname value.

Recommended Response Action

Make sure that the correct proxy hostname value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS243

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported proxy port number value, arg2.

Arguments

arg1 = filename
arg2 = bad proxy port number

Detailed Description

The file cannot be transferred because of an unsupported proxy port number value.

Recommended Response Action

Make sure that the correct proxy port number value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS244

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported proxy workgroup value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because a proxy workgroup value is not entered, or the entered value is not supported.

Recommended Response Action

Make sure that the correct proxy workgroup value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS245

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported proxy username value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because a proxy username value is not entered, or the entered value is not supported.

Recommended Response Action

Make sure that the correct proxy username value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS246

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported proxy password value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because a proxy password value is not entered, or the entered value is not supported.

Recommended Response Action

Make sure that the correct proxy password value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS247

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because credentials are not entered, or the credentials entered do not correspond to an authorized user of the remote host.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because credentials are not entered, or the credentials entered do not correspond to an authorized user of the remote host.

Recommended Response Action

Make sure that the correct credentials are entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS248

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the proxy credentials are not entered, or the proxy credentials entered do not correspond to an authorized user of the proxy server.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because proxy credentials are not entered, or the proxy credentials entered do not correspond to an authorized user of the proxy server.

Recommended Response Action

Make sure that the correct proxy credentials are entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS249

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A network connection is successfully started to the remote host, but the file, arg1, is unable to be transferred.

Arguments

arg1 = filename

Detailed Description

A network connection is successfully started to the remote host, but the file is unable to be transferred.

Recommended Response Action

Make sure that correct parameters are entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS250

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an internal error.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an internal issue. This is not related to any issue in network, proxy status, or remote host status.

Recommended Response Action

Check the system health and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS251

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the file is not available at the source file path.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the file is not available at the source file path.

Recommended Response Action

Check the file transfer parameters and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS252

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the file is not available at the remote host location.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the file is not available at the remote host location.

Recommended Response Action

Make sure that the file is available at the remote host location and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS253

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the remote host server or remote host file system is set to read-only mode.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the remote host server or remote host file system is set to read-only mode.

Recommended Response Action

Make sure that the file transfer parameters and the remote host file system properties are correct, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS254

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of one or more of the following: 1) remote host cannot be reached. 2) remote share name is not present. 3) incorrect credentials are entered.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of one or more of the following: 1) remote host cannot be reached. 2) remote share name is not present. 3) incorrect credentials were entered.

Recommended Response Action

Make sure that the file transfer parameters are correct, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS255

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an unsupported verify certificate value.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because a verify certificate value is not entered, or the entered value is not supported.

Recommended Response Action

Make sure that the correct verify certificate value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS256

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of an out-of-memory condition.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because of an out-of-memory condition. The issue is not because of network conditions, proxy status, or remote host status.

Recommended Response Action

Check the iDRAC health and retry the operation. If the issue persists, restart the iDRAC and retry the operation after the iDRAC has fully restarted.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS257

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the verification certificate is not available.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the verification certificate is not available. The file transfer settings are set to verify the certificate of the remote host server, but the necessary verification certificate is not uploaded.

Recommended Response Action

Upload the verification certificate or select the Ignore Certificate Warning setting, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS258

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because there is a problem with the remote host servers security certificate.

Arguments

arg1 = filename

Detailed Description

The remote host server certificate was validated against the uploaded certificate and the validation did not succeed. The remote host server certificate does not correspond to the uploaded verification certificate. The certificate subject name, CN part, may not match the domain name used. If the uploaded certificate is correct, the IP address of the remote host server may be incorrect, the certificate may be expired or this error could indicate a Man-In-The-Middle attack in progress.

Recommended Response Action

Make sure that the following are correct and retry the operation: a) the file transfer parameters b) the uploaded certificate corresponds to the remote host server c) the certificate subject name, CN part, matches the domain name used.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS259

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the resume value is not supported.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the resume value is not supported.

Recommended Response Action

Make sure that the resume value is correct and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS260

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the destination file system does not have sufficient free space or does not have sufficient free user quota.

Arguments

arg1 = filename

Detailed Description

Unable to transfer a file because the destination file system does not have sufficient free space or does not have sufficient free user quota.

Recommended Response Action

Make sure that the following are correct and retry the operation: a) file transfer parameters b) remote host file system free space.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS261

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer the file, arg1, because initial network connection to the remote host server is not successfully started.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because initial network connection to the remote host server is not successfully started. The other probable reasons are: 1) issue in the network 2) remote host server is not turned on 3) remote host server is turned on but not functioning 4) issue in protocol negotiation.

Recommended Response Action

Check the file transfer parameters, health of the remote host, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS262

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because either the proxy may not allow file transfer operations or incorrect proxy credentials are entered.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because either the proxy may not allow file transfer operations or incorrect proxy credentials are entered.

Recommended Response Action

Make sure that correct proxy settings are enabled and correct proxy credentials are entered and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS263

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the operation is taking longer time than the set time limit.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the operation is taking longer time than the set time limit. The other probable reasons are: 1) issue in the network 2) remote host server is not turned on 3) remote host server is turned on but not functioning 4) issue in protocol negotiation.

Recommended Response Action

Check the file transfer parameters, health of the remote host, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS264

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the proxy server was incapable of performing the file transfer operations.

Arguments

arg1 = filename

Detailed Description

Unable to transfer a file because the proxy server was incapable of performing the file transfer operations even when the network connection is available to the proxy server.

Recommended Response Action

Make sure that correct proxy settings and file transfer parameters are set, and then retry the operation. If the issue persists, try connecting to a different proxy.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS265

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the remote host server did not allow file transfer operations.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the remote host server did not allow file transfer operations even when the remote host is successfully contacted.

Recommended Response Action

Make sure that the file transfer parameters and credentials, and remote host server configuration are correct, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS266

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because either an unsupported access type value is set or the value is not set at all.

Arguments

arg1 = filename

Detailed Description

Unable to transfer a file because either an unsupported access type value is set or the value is not set at all.

Recommended Response Action

Make sure that correct access type value is entered, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS267

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the network connection from the proxy server to the remote host server is unsuccessful.

Arguments

arg1 = filename

Detailed Description

Unable to transfer a file because the network connection from the proxy server to the remote host server is unsuccessful.

Recommended Response Action

Make sure that correct file transfer parameters are set, the health of remote host is good, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS268

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because the proxy operation is taking longer time than the set time limit.

Arguments

arg1 = filename

Detailed Description

The file cannot be transferred because the proxy operation is taking longer time than the set time limit of the proxy configuration. The other possible reasons are: 1) issue in the network 2) remote host server may not be turned on 1) remote host server is turned on but not functioning 4) an issue in protocol negotiation.

Recommended Response Action

Check the file transfer parameters, health of the remote host, the proxy time limit configuration and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS269

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to change the Federal Information Processing Standards (FIPS) attribute because the feature is not supported by using Server Configuration Profile (SCP), and the attribute setting is not applied.
Detailed Description: The Federal Information Processing Standards (FIPS) attribute cannot be changed because the feature is not supported by using Server Configuration Profile (SCP), and the attribute setting is not applied.
Recommended Response Action: To set Federal Information Processing Standards (FIPS) attribute to enabled using the RACADM command line utility, type "racadm set idrac.security.fipsmode enabled".
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS270

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Refer to error message ID: arg2.

Arguments

arg1 = System event message
arg2 = message ID

Detailed Description

An event is logged in the IPMI System Event Log (SEL) for a sensor not specifically monitored by Open Manage Server Administrator (OMSA). For more information about the error message ID identified in the message, see the Event and Error Message Reference Guide available on the support site.

Recommended Response Action

For more information about the error message ID identified in the message, see the Event and Error Message Reference Guide for Servers available on the support site.

Category

System Health (SYS = System Info)

Severity

Informational

OMSA Event ID

5015

OMSA Trap ID

5015

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SYS271

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Refer to error message ID: arg2.

Arguments

arg1 = System event message
arg2 = message ID

Detailed Description

Recommended Response Action

For more information about the error message ID identified in the message, see the Event and Error Message Reference Guide for Servers available on the support site.

Category

System Health (SYS = System Info)

Severity

Warning

OMSA Event ID

5016

OMSA Trap ID

5016

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SYS272

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Refer to error message ID: arg2.

Arguments

arg1 = System event message
arg2 = message ID

Detailed Description

A critical event is logged in the IPMI System Event Log (SEL) for a sensor not specifically monitored by Open Manage Server Administrator (OMSA). For more information about the error message ID identified in the message, see the Event and Error Message Reference Guide available on the support site.

Recommended Response Action

For more information about the error message ID identified in the message, see the Event and Error Message Reference Guide for Servers available on the support site.

Category

System Health (SYS = System Info)

Severity

Critical

OMSA Event ID

5017

OMSA Trap ID

5017

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SYS273

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to update the firmware version because of one or more missing firmware update prerequisites.
Detailed Description: The firmware version cannot be updated because of one or more missing firmware update prerequisites.
Recommended Response Action: Make sure that the prerequisite firmwares are installed, and then retry updating the firmware. For information about prerequisite firmware, see the iDRAC Users Guide available on the support site.
Category: Updates (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS274

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to apply the firmware file arg1 because one or more missing firmware update prerequisites.

Arguments

arg1 = filename

Detailed Description

The file identified in the message cannot be applied because of one or more missing firmware update prerequisites.

Recommended Response Action

Make sure that the prerequisite firmware updates are installed, and then retry updating the firmware. For information about prerequisite firmware, see the iDRAC Users Guide available on the support site.

Category

Updates (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS275

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to apply the firmware file arg1 because the firmware update prerequisite arg2 is not installed.

Arguments

arg1 = filename
arg2 = prerequisite firmware filename

Detailed Description

The file identified in the message cannot be applied because the firmware update prerequisite identified in the message is not installed.

Recommended Response Action

Make sure that the firmware prerequisite identified in the message is installed, and then retry updating the firmware. For information about prerequisite firmware, see the iDRAC Users Guide available on the support site.

Category

Updates (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS276

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The firmware file arg1 will be successfully applied, but only limited features are made available for use until the firmware update prerequisite arg2 is fully installed.

Arguments

arg1 = filename
arg2 = prerequisite firmware filename

Detailed Description

The file identified in the message will be applied, but only limited features are made available for use until the firmware update prerequisite identified in the message is fully installed.

Recommended Response Action

No response action is required for using base features. However, to use all features, make sure that the firmware prerequisite identified in the message is installed, and then retry updating the firmware. For information about prerequisite firmware, see the iDRAC Users Guide available on the support site.

Category

Updates (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS277

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the TTY log data because network share cannot be mounted.
Detailed Description: The TTY log data cannot be exported because the network share cannot be mounted.
Recommended Response Action: Make sure that the correct network information is entered and retry the operation.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS278

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The factory assigned MAC address of iDRAC is restored which may cause the iDRAC to restart in some situations.
Detailed Description: The factory-assigned MAC address of iDRAC is restored which may cause the iDRAC to restart in some situations. iDRAC is restarted by using a factory default MAC address that can potentially change the DHCP assigned iDRAC IP address.
Recommended Response Action: No response action is required. However, if this message is displayed multiple times indicating that the MAC address of iDRAC is restored to factory default, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS279

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC is not ready for processing ISM requests. Retry after 1 minute.
Detailed Description: iDRAC is not ready for processing ISM requests. Retry after 1 minute.
Recommended Response Action: Retry the operation after 1 minute.
Category: Audit (SYS = System Info)
Severity: Informational
Trap/EventID: 8579
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS285

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to read Repository Update file because the Repository Update file path has more than 1024 characters.
Detailed Description: The Repository Update file cannot be read because the Repository Update file path has more than 1024 characters.
Recommended Response Action: Make sure that the Repository Update file path has less than 1024 characters and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS286

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to preview the update status because the specified catalog file does not exist on the remote share.
Detailed Description: The update status cannot be previewed because the specified catalog file does not exist on the remote share.
Recommended Response Action: Do the following and retry the operation: 1) Make sure that the specified catalog file is available on the remote share. 2) Make sure that the Repository Update file path has less than 1024 characters and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS287

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the Repository Update operation because the specified catalog file does not exist on the remote share.
Detailed Description: The Repository Update operation cannot be performed because the specified catalog file does not exist on the remote share.
Recommended Response Action: Make sure that the specified catalog file is available on the remote share, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS288

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to get the Repository Update catalog file from the network share for preview because the file does not exist in the specified location.
Detailed Description: The catalog file cannot be obtained from the network share for preview because the file does not exist in the specified location.
Recommended Response Action: Make sure that the specified catalog file is available on the remote share, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS289

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to get the Repository Update catalog file from the network share for import because the file does not exist in the specified location.
Detailed Description: The catalog file cannot be obtained from the network share for importing because it does not exist in the specified location.
Recommended Response Action: Make sure that the specified catalog file is available on the remote share, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS290

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The System Lockdown feature is enabled.
Detailed Description: The System Lockdown feature is enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS291

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the configuration operation because System Lockdown mode is enabled.
Detailed Description: The configuration operation cannot be started because the System Lockdown mode is enabled.
Recommended Response Action: Make sure that the Lockdown.1#SystemLockdown attribute is set to Disabled and then retry the operation. For information about the Lockdown mode, see the relevant iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS293

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Component configuration preview was successful.
Detailed Description: The configuration changes for the component identified by the Fully Qualified Device Descriptor (FQDD) was successfully previewed.
Recommended Response Action: No response action is required. For more information, see the Lifecycle Log data.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS294

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Component configuration preview was completed with errors.
Detailed Description: Some configuration changes for the component identified by the Fully Qualified Device Descriptor (FQDD) in the configuration job results were not successfully previewed.
Recommended Response Action: Do the following: 1) Export the Lifecycle Log report and check the configuration changes that did not complete. 2) Retrieve the configuration results by running the GetConfigResults method at the command line interface (CLI). 3) Retry importing the changes that are not successfully completed.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS295

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete component configuration preview.
Detailed Description: Configuration changes for the components identified by the Fully Qualified Device Descriptor (FQDD) in the configuration job results were not successfully previewed.
Recommended Response Action: Do the following: 1) Export the Lifecycle Log report and check the configuration changes that did not complete. 2) Retrieve the configuration results by running the GetConfigResults method at the command line interface (CLI). 3) Retry importing the changes that are not successfully completed.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS296

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Server Configuration Profile Import job is scheduled. After the next server reboot, the configurations will be automatically applied.
Detailed Description: The Server Configuration Profile Import job is scheduled. After the next server reboot, the configurations will be automatically applied.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS297

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to expand the compressed file because the password entered for ZipPassword attribute in the iDRAC does not match with the password used for protecting the compressed file. Or, the encryption type used is not supported by the iDRAC.
Detailed Description: The compressed file cannot be expanded because because the password entered for ZipPassword attribute in the iDRAC does not match with the password used for protecting the compressed file. Or, the encryption type used is not supported by the iDRAC.
Recommended Response Action: Make sure that the password entered for ZipPassword attribute on the iDRAC is same as the password used to encrypt the compressed file and use the default (ZipCrypto) encryption.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS298

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the import operation either because the Server Configuration Profile file is not available on the USB drive, or because the USB drive has more than one compressed file.
Detailed Description: The import operation cannot be started either because the Server Configuration Profile file is not available on the USB drive, or because the USB drive has more than one compressed file.
Recommended Response Action: Make sure of the following and retry the operation: 1) The correct Server Configuration Profile file is available on the USB drive. 2) Only one compressed file is stored on the USB drive, if stored in a compressed file.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS299

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to open the compressed file because the ZipPassword attribute is set and no password is used for protecting the compressed file.
Detailed Description: The compressed file cannot be opened because there is a password entered for the ZipPassword attribute on the iDRAC, while no password is used to protect the compressed file.
Recommended Response Action: Make sure that the password entered for ZipPassword attribute on the iDRAC is same the password used to encrypt the compressed file.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS300

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the import operation because the Control file has incorrect schema.
Detailed Description: The import operation cannot be started because the Control file has incorrect schema.
Recommended Response Action: Make sure that the input file is compliant with the Control file schema described in the Lifecycle Controller Profile Schema Guide available on the delltechcenter.com/lc.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS301

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: OS Deployment cannot be performed because Repository Update will downgrade the iDRAC to a version that does not support this feature.
Detailed Description: The import operation will be unable to complete the OS Deployment portion of this template because Repository Update will downgrade the iDRAC to a version that does not support OS Deployment.
Recommended Response Action: The OS Deployment operation will need to be completed separately after the iDRAC update has completed.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS302

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The vFlash Erase operation is successfully completed.
Detailed Description: The vFlash Erase operation is successfully completed.
Recommended Response Action: No response action required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS303

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the TTY Log report because an operation is currently in progress to export another TTY Log report.
Detailed Description: The TTY Log report cannot be exported because an operation is currently in progress to export another TTY Log report.
Recommended Response Action: Wait for the current export operation to complete and retry the operation. To view the TTY Log export operation information, click Controller > Troubleshooting > Export TTYLog.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS304

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The import operation cannot be performed because the RepositoryUpdate feature is not supported for local imports.
Detailed Description: The import operation cannot be performed because the RepositoryUpdate feature is not supported for local imports.
Recommended Response Action: Remove the value from the RepositoryUpdate attribute under the System.Embedded.1 component.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS305

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because no device configuration could be identified for the specified FQDDs.
Detailed Description: The operation cannot be completed because no device configuration could be identified for the specified FQDDs.
Recommended Response Action: Make sure that only valid FQDDs are entered as input to the Target parameter, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS306

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to copy the Server Configuration Profile to the network share because of insufficient space on the share.
Detailed Description: The Server Configuration Profile cannot be copied to the network share because of insufficient space on the share.
Recommended Response Action: Make sure that enough space is available on the network share and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS307

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform system erase of NVDIMM because there are no Non Volatile memory devices in the system.
Detailed Description: NVDIMM erase operation was unsuccessful. This may be because of non volatile memory devices not present in the system.
Recommended Response Action: Ensure NVDIMM(s) are present and then retry the System Erase operation with only NVDIMM option selected.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS308

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the System Erase operation because the system is in the Manufacturing mode.
Detailed Description: The System Erase operation cannot be completed because the system is in the Manufacturing mode.
Recommended Response Action: Make sure that the system is not in the Manufacturing mode, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS309

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the System Erase operation because the necessary components or communication elements are unavailable.
Detailed Description: The System Erase operation cannot be completed because the necessary components or communication elements are unavailable.
Recommended Response Action: Update to the iDRAC version that has necessary components, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS310

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid System Erase request.
Detailed Description: System Erase operation was unsuccessful. The System Erase operation detected the request did not include iDRAC. In the configured mode of operation no other selections are valid.
Recommended Response Action: In the currently configured mode of operation, the request is invalid. Retry the System Erase operation including the idrac selection.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS311

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The System Erase operation is successfully completed.
Detailed Description: The System Erase operation is successfully completed.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS312

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to successfully complete one or all the tasks necessary for completing the System Erase request.
Detailed Description: One or more tasks required to successfully complete the System Erase operation cannot be completed.
Recommended Response Action: Check logs for additional information.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS313

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the phase-1 tasks of System Erase request.
Detailed Description: One or more tasks required to successfully complete the phase-1 tasks of System Erase operation cannot be completed.
Recommended Response Action: Check logs for additional information.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS314

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the phase-2 tasks of System Erase request.
Detailed Description: One or more tasks required to successfully complete the phase-2 tasks of System Erase operation cannot be completed.
Recommended Response Action: Check logs for additional information.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS315

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to transfer a file, arg1, because of the reason described by the code arg2 sent by the FTP remote host server.

Arguments

arg1 = filename
arg2 = ftp response code

Detailed Description

The file cannot be transferred because of the reason described by the code identified in the message. For every unsuccessful file transfer, the FTP remote host server returns an error code, where each code has a description about the reason for failure.

Recommended Response Action

View the FTP remote host server documentation to resolve the issue. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS316

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because either an attribute is not entered or an incorrect attribute is entered.
Detailed Description: The operation cannot be completed because either an attribute is not entered or an incorrect attribute is entered.
Recommended Response Action: Make sure to enter a valid attribute and retry the operation. For information about valid values, see the Lifecycle Controller Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS317

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the certificate because either an invalid Certificate Payload parameter is entered, or the BEGIN or END Encapsulation Boundary line parameter is not entered.
Detailed Description: The certificate cannot be imported because either an invalid Certificate Payload parameter is entered, or the BEGIN or END Encapsulation Boundary line parameter is not entered.
Recommended Response Action: Enter a valid Certificate Payload parameter and Encapsulation Boundary line parameter, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS318

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the certificate because an invalid certificate type is entered.
Detailed Description: The certificate cannot be imported because an invalid certificate type is entered.
Recommended Response Action: Enter a valid certificate type and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS319

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because either the required license is missing or expired.
Detailed Description: The operation cannot be completed because either the required license is missing or expired.
Recommended Response Action: Obtain the necessary license and retry the operation. For more information about the features supported by different license categories, see the Lifecycle Controller Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS320

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because an invalid parameter arg1 is entered.

Arguments

arg1 = parameter name

Detailed Description

The operation cannot be completed because an invalid parameter is entered as identified in the message.

Recommended Response Action

Enter a valid parameter and retry the operation. For information about valid parameters, see the Redfish API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS321

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The server is either idle or underutilized for the last arg1 hours.

Arguments

arg1 = hours

Detailed Description

The server is either idle or underutilized for the last few hours as identified in the message.

Recommended Response Action

You can consider optimizing the server load. For information about optimizing the server load, refer to the respective Server Solutions documentation.

Category

System Health (SYS = System Info)

Severity

Informational

Trap/EventID

2435

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS322

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the application of the Server Configuration Profile because the OS driver pack is currently attached.
Detailed Description: The Server Configuration Profile (SCP) cannot be applied because the OS driver pack is still attached.
Recommended Response Action: Retry the application of the Server Configuration Profile after the OS driver pack expose duration has expired.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS323

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to run the command because the value entered for ExposeDuration is out of range.
Detailed Description: The command cannot be run because the value entered for ExposeDuration is out of range.
Recommended Response Action: Enter an ExposeDuration value from 300 to 65,535, and then rerun the command. For more information about the Export Duration value, see the iDRAC Users Guide and RACADM CLI Reference Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS324

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Lockdown Configuration value is successfully applied to arg1.

Arguments

arg1 = device Name

Detailed Description

The Lockdown Configuration value is successfully applied to the device identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS325

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to apply the Lockdown Configuration value is to the arg1 device because of an internal error.

Arguments

arg1 = device Name

Detailed Description

Lockdown configuration values were not applied to the device identified in the message because of an internal error.

Recommended Response Action

Retry the operation. If the issue persists, reset the iDRAC using "racadm racreset" CLI command.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS326

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the System Erase operation because of an internal error arg1.

Arguments

arg1 = error code

Detailed Description

The System Erase operation cannot be completed because of a processing error identified in the message.

Recommended Response Action

Reset the iDRAC by using "racadm racreset" command. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS327

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to shut down the host to complete the System Erase operation.
Detailed Description: The System Erase operation will attempt a graceful shutdown. After 10 minutes, if the host has not reached a powered off state then System Erase will perform a forced shutdown. This event was generated because both the graceful and forced shutdown attempts failed.
Recommended Response Action: Shut down the host before performing the System Erase operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS328

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to restore previous system content, because after replacing the motherboard and rebooting the server, "N" was selected to indicate that a system content restoration is not required.
Detailed Description: The previous system content cannot be restored, because after replacing the motherboard and rebooting the server, "N" was selected to indicate that a system content restoration is not required. Some examples of system content that can be restored are Service Tag, SupportAssist SEL, Enterprise UEFI Diagnostics and licenses.
Recommended Response Action: Do the following: 1) Restart the server. 2) When prompted that a new system motherboard is detected and the system content can be restored, select Y (Yes). To reboot the host by using Graphical User Interface (GUI), on Dashboard Page, click Drop down Box near Graceful Shutdown > Reset System (Warm boot). To reset by using RACADM, run the command at the Command Line Interface (CLI): racadm serveraction powercycle.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS329

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Performing a virtual AC power-cycle operation to enable the recent firmware updates.
Detailed Description: Performing a virtual AC power-cycle operation to enable the recent firmware updates.
Recommended Response Action: No response action is required. To view the status of Upload Custom Default job or export the Lifecycle Log to review the job results, run the following method at the Command Line Interface (CLI): GetConfigResults(). Else, view the Job Queue page to view the job status.
Category: Updates (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS330

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Custom Defaults file is being validated and will be saved (uploaded) if no issues are detected.
Detailed Description: The Custom Defaults file is being validated and will be saved (uploaded) if no issues are detected.
Recommended Response Action: No response action is required. To view the status of Upload Custom Default job or export the Lifecycle Log to review the job results, run the following method at the Command Line Interface (CLI): GetConfigResults(). Else, view the Job Queue page to view the job status.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS331

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to upload the Custom Defaults file to iDRAC.
Detailed Description: The Custom Defaults file cannot be uploaded to iDRAC.
Recommended Response Action: 1) Run the following method at the Command Line Interface (CLI) to view any detected errors: GetConfigResults(). 2) Resolve the errors and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS332

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Custom Defaults file is successfully uploaded to iDRAC.
Detailed Description: The Custom Defaults file is successfully uploaded to iDRAC.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS333

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The custom default setting are successfully uploaded, and then stored on iDRAC.
Detailed Description: The custom default setting are successfully uploaded, and then stored on iDRAC.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS334

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The template provided is not compliant with the configuration profile schema.
Detailed Description: The input file is not compliant with the system configuration schema.
Recommended Response Action: Make sure that the input file is compliant with the system configuration schema published on delltechcenter.com/lc in the Lifecycle Controller profile Schema Guide.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS335

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A new hash value is created for the current system configuration.
Detailed Description: A new hash value is created for the current system configuration, and then saved as configuration data.
Recommended Response Action: No response action required.
Category: Configuration (SYS = System Info)
Severity: Informational
Trap/EventID: 10627
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS336

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An existing hash value is updated because some system configuration items are changed.
Detailed Description: An existing hash value is updated because some system configuration items are changed. The updated hash value is changed as configuration data.
Recommended Response Action: No response action required.
Category: Configuration (SYS = System Info)
Severity: Informational
Trap/EventID: 10627
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS337

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A new hash value is created for the system software inventory and saved to the corresponding attribute.
Detailed Description: A new hash value is created for the system software inventory and saved to the corresponding attribute.
Recommended Response Action: No response action required.
Category: Configuration (SYS = System Info)
Severity: Informational
Trap/EventID: 10627
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS338

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An existing hash value is updated because some system software inventory values are changed. The updated data is saved to the corresponding attribute.
Detailed Description: An existing hash value is updated because some system software inventory values are changed. The updated data is saved to the corresponding attribute.
Recommended Response Action: No response action required.
Category: Configuration (SYS = System Info)
Severity: Informational
Trap/EventID: 10627
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS339

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A new hash value is created for the system hardware inventory and saved to the corresponding attribute.
Detailed Description: A new hash value is created for the system hardware inventory and saved to the corresponding attribute.
Recommended Response Action: No response action required.
Category: Configuration (SYS = System Info)
Severity: Informational
Trap/EventID: 10627
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS340

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An existing hash value is updated because some hardware inventory values are changed.
Detailed Description: An existing hash value is updated because some hardware inventory values are changed. The updated hash value is saved into attribute.
Recommended Response Action: No response action required.
Category: Configuration (SYS = System Info)
Severity: Informational
Trap/EventID: 10627
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS400

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to successfully complete the precondition check operations such as Open Data Protocol (OData) Version, If-Match request-header, and If-Not-Modified request-headers.
Detailed Description: The precondition check operation such as Open Data Protocol (OData) Version, If-Match request-header, and If-Not-Modified request-headers cannot be completed.
Recommended Response Action: Make sure that the prerequisites specified for the request are satisfied. For more information about the prerequisites, see the Redfish Specification and Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS401

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the media type entered is not supported.
Detailed Description: The operation cannot be successfully completed because the media type entered is not supported.
Recommended Response Action: Enter a media type that is supported and retry the operation. For more information about the supported media types, see the Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS402

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to run the method because the requested HTTP method is not allowed.
Detailed Description: The method cannot be run because the requested HTTP method is not allowed.
Recommended Response Action: Enter a valid HTTP method and retry the operation. For information about valid methods, see the Redfish Users Guide available on the support site.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS403

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the resource arg1 entered is not found.

Arguments

arg1 = resource name

Detailed Description

The operation cannot be successfully completed because the resource identified in the message does not exist.

Recommended Response Action

Enter the correct resource and retry the operation. For resources with numeric ID in the URI, enable the "Redfish.1#NumericDynamicSegmentsEnable" attribute and retry the operation. For information about valid resource, see the Redfish Users Guide available on the support site.

Category

Audit (SYS = System Info)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS404

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the If-Match request header is missing.
Detailed Description: The operation cannot be successfully completed because the If-Match request header is missing.
Recommended Response Action: Make sure that the If-Match request header is entered and retry the operation. For information about the necessary headers, see the Redfish specification and Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS405

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the JSON data format entered is invalid.
Detailed Description: The request cannot be successfully completed because the JSON data format entered is invalid.
Recommended Response Action: Do the following and the retry the operation: 1) Enter the correct JSON data format and retry the operation. 2) Make sure that no syntax error is present in JSON data format. 3) Make sure that a duplicate key is not present in JSON data format.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS406

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the configuration operation because the System Lockdown mode is enabled.
Detailed Description: The configuration operation cannot be started because the System Lockdown mode is enabled.
Recommended Response Action: Make sure that the Lockdown.1.SystemLockdown attribute is set to Disabled by running the HTTP PATCH method on "Managers OemAttributes" Redfish API, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS407

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the value arg1 entered for the query parameter arg2 is invalid.

Arguments

arg1 = value
arg2 = query param

Detailed Description

The operation cannot be completed because the value entered for the query parameter identified in the message is invalid.

Recommended Response Action

Enter a valid value and retry the operation. The minimum value that can entered for top query parameter is 1.

Category

Audit (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS408

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Only one task ID is displayed in the response.
Detailed Description: Only one task ID is displayed. By default, the location response header displays information about only one task ID.
Recommended Response Action: To view all task IDs, run the "Tasks" Redfish API.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS409

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set the object properties because an incorrect object value is entered.
Detailed Description: The object properties cannot be set because an incorrect object value is entered.
Recommended Response Action: Enter a valid object value and retry the operation. For information about recommended values, see the schema or the attribute registry based on the type of resource.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS410

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to modify the attribute because the attribute is read-only and depends on other attributes.
Detailed Description: The attribute cannot be modified because the attribute is read-only and depends on other attributes. Some attributes have dependencies on other attributes that are required to perform a task. However, some of the attributes are read-only because of the current system configuration and the values of the dependent attributes.
Recommended Response Action: Verify if the attribute has dependency on other attributes and retry the operation. To verify, view the attribute registry based on the type of resource.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS411

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to upload the file because the file size is greater than specified limit.
Detailed Description: The file cannot be uploaded because the file size is greater than specified limit.
Recommended Response Action: Make sure that the file size is less than the specified limit. For information about specified limit, see the Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS412

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to upload the file because of unknown internal issues.
Detailed Description: The file cannot be uploaded because of unknown internal issues.
Recommended Response Action: Retry the operation. If the issue persists, reset the iDRAC, and then retry the operation. Reset the iDRAC by using the "Manager Reset Actions" Redfish API.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS413

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation successfully completed.
Detailed Description: The operation successfully completed as all conditions have been met.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS414

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A new resource is successfully created.
Detailed Description: A new resource is successfully created.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS415

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because an invalid username and/or password is entered, and therefore authentication failed.
Detailed Description: The operation cannot be completed because an invalid username and/or password is entered, and therefore authentication failed.
Recommended Response Action: Enter valid user name and password and retry the operation.
Category: Audit (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS416

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the username and/or password is not entered, and therefore authentication failed.
Detailed Description: The operation cannot be completed because the username and/or password is not entered, and therefore authentication failed.
Recommended Response Action: Enter valid user name and password and retry the operation.
Category: Audit (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS417

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the value arg1 entered for the query parameter arg2 is out of range arg3.

Arguments

arg1 = value
arg2 = query param
arg3 = range

Detailed Description

The operation cannot be successfully completed because the value entered for the query parameter is out of range as identified in the message.

Recommended Response Action

Enter a query parameter value within range and retry the operation.

Category

Audit (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS418

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to send the test event because the Alert service is disabled.
Detailed Description: The test event cannot be sent because the Alert service is disabled.
Recommended Response Action: Enable the attribute IPMILan.1.AlertEnable by using the PATCH operation on the Redfish OemAttributes URL, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS419

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the Redfish attribute is disabled.
Detailed Description: The operation cannot be successfully completed because the Redfish attribute is disabled.
Recommended Response Action: Make sure that the Redfish.1.Enable attribute is set to Enabled using other iDRAC interfaces, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS420

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the Redfish URI version arg1 is not supported.

Arguments

arg1 = version

Detailed Description

The operation cannot be completed because the Redfish URI version identified in the message is not supported.

Recommended Response Action

Enter a valid URI version and retry the operation. For information about valid URI versions, see the Redfish Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS421

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Active Directory object DCLookupByUserDomain cannot be disabled, because the DCLookupDomainName object of Active Directory is not configured.
Detailed Description: The Active Directory object DCLookupByUserDomain cannot be disabled, because the DCLookupDomainName object of Active Directory is not configured.
Recommended Response Action: Configure the DCLookupDomainName object by using the PATCH operation on the Redfish OemAttributes URL, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS422

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to display the ETag in the response headers because of unknown internal issues.
Detailed Description: The ETag in the response headers cannot be displayed because of unknown internal issues.
Recommended Response Action: Retry the operation. If the issue persists, reset the iDRAC, and then retry the operation. Reset the iDRAC by using the "Manager Reset Actions" Redfish API.
Category: Audit (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS423

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to send the test event because there are no subscriptions.
Detailed Description: The test event cannot be sent because there are no subscriptions.
Recommended Response Action: Create a subscription using HTTP POST operation to the URI of the subscription resource.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS424

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the value arg1 entered for the property arg2 is of different type than the property can accept.

Arguments

arg1 = value
arg2 = property

Detailed Description

The operation cannot be completed because the value entered for the property identified in the message is of invalid type.

Recommended Response Action

Enter a valid value in the expected type for the property in the request body and retry the operation. For information about valid values, see the iDRAC Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS425

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the value arg1 entered for the property arg2 is invalid.

Arguments

arg1 = value
arg2 = property

Detailed Description

The operation cannot be completed because the value entered for the property identified in the message is not supported.

Recommended Response Action

Enter a valid value for the property in the request body and retry the operation. For information about valid values, see the iDRAC Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS426

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the value arg1 entered for the property arg2 is not in the list of acceptable values.

Arguments

arg1 = value
arg2 = property

Detailed Description

The operation cannot be completed because the value entered for the property identified in the message is not in the enumeration list.

Recommended Response Action

Enter a valid value from the enumeration list that Redfish service supports and retry the operation. For information about valid values, see the iDRAC Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS427

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the property arg1 is a read only property and cannot be assigned a value.

Arguments

arg1 = property

Detailed Description

The operation cannot be completed because the property identified in the message is a read only property.

Recommended Response Action

Remove the property from the request body and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS428

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the property arg1 is a required property and must be included in the request.

Arguments

arg1 = property

Detailed Description

The operation cannot be completed because the property identified in the message is not supplied as part of the request.

Recommended Response Action

Make sure that the property is in the request body and has a valid value, and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS429

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the property arg1 is not in the list of valid properties for the resource.

Arguments

arg1 = property

Detailed Description

The operation cannot be completed because the property is not in the list of valid properties for the resource.

Recommended Response Action

Remove the unknown property from the request body and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS430

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation is successfully completed.
Detailed Description: The operation is successfully completed. The configuration changes will become effective after restarting the host server next time.
Recommended Response Action: No response action is required.However, to make them immediately effective, restart the host server.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS431

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to apply the configuration changes because an import or export operation is currently in progress.
Detailed Description: The import or export configuration changes cannot be applied because an import or export operation is currently in progress.
Recommended Response Action: Wait for the current import or export operation to complete and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS432

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set the Power Cap value because the PowerCapSetting feature is disabled.
Detailed Description: The Power Cap value cannot be set because the PowerCapSetting feature is disabled.
Recommended Response Action: Enable the PowerCapSetting feature by using the PATCH operation on the Redfish OemAttributes URL, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS433

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to upload the server configuration profile data because the file type used for the data file is not in the JSON or XML format.
Detailed Description: The server configuration profile data cannot be uploaded because the file type used for the data file is not in the JSON or XML format.
Recommended Response Action: Make sure that the file format used is of JSON or XML format, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS434

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to upload the firmware image because the file extension is not supported.
Detailed Description: The operation cannot be completed because the uploaded firmware image file extension is not supported.
Recommended Response Action: Make sure to use a valid firmware image and retry the operation. For information about the supported file extension types, see the Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS435

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the BIOS configuration data either because the system inventory is not collected, Lifecycle Controller Wipe operation is performed, or because of a system error.
Detailed Description: The BIOS configuration data cannot be retrieved either because the system inventory is not collected, Lifecycle Controller Wipe operation is performed, or because of a system error.
Recommended Response Action: Enable the Lifecycle Controller CSIOR (Collect System Inventory on Restart) feature, collect the system inventory, and then retry the operation. To enable CSIOR and Lifecycle Controller respectively perform the PATCH operation for these attributes on the Redfish OemAttributes URL.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS436

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create the job because the Start Time entered is invalid.
Detailed Description: The job cannot be created because the Start Time entered is invalid.
Recommended Response Action: Enter the Start Time in the String format, and then retry the operation For example, YYYY-MM-DDTHH:MM:SS. For more information about recommended Start Time format, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS437

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create the job because the EndTime value entered is less than 5 minutes of StartTime value.
Detailed Description: The job cannot be created because the EndTime value entered is less than 5 minutes of StartTime value.
Recommended Response Action: Enter an EndTime value that is greater than 5 minutes of the StartTime value.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS438

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to reset the Secure Boot keys because the installed BIOS version does not support the operation.
Detailed Description: The Secure Boot keys cannot be reset because the installed BIOS version does not support the operation.
Recommended Response Action: Update the BIOS to the latest version and retry the operation. For information about updating BIOS, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS439

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the Secure Boot policy is set to Standard.
Detailed Description: The operation cannot be completed because the Secure Boot policy is set to Standard.
Recommended Response Action: Reset the Secure Boot policy to Custom by performing the PATCH operation for the SecureBootPolicy attribute on the Redfish Bios URL.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS440

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to Create Job because the End Time entered is invalid.
Detailed Description: The Job creation cannot be done because the End Time entered is invalid.
Recommended Response Action: Enter the End Time in the String format, and then retry the operation For example, YYYY-MM-DDTHH:MM:SS. For more information about recommended End Time format, see the iDRAC Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS441

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the index arg1 entered is not a valid offset in the array.

Arguments

arg1 = index

Detailed Description

The operation cannot be completed because the index entered as identified in the message is not a valid offset in the array.

Recommended Response Action

Enter a valid index within the limits of the array and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS442

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the installation because more than one firmware inventory component URI is entered.
Detailed Description: The installation process cannot be started because more than one firmware inventory component URI is entered.
Recommended Response Action: Enter only one firmware inventory component URI for installation and retry the operation. For information about the allowed URIs, see the Schema and Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS443

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to configure the object because the object has dependencies on other objects that must be present for successful configuration.
Detailed Description: The object cannot be configured because the object has dependencies on other objects that must be present for successful configuration.
Recommended Response Action: Verify the object dependency by using AttributeRegistry available in the Service Root Registries URI.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS444

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set the attribute value because it depends on other attribute(s).
Detailed Description: The attribute value cannot be set because it depends on other attribute(s).
Recommended Response Action: Change the value on the other attribute and retry the operation. For information about attribute dependency, see the Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS445

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the value arg1 entered for the query parameter arg2 is invalid.

Arguments

arg1 = value
arg2 = query param

Detailed Description

The operation cannot be completed because the value entered for the query parameter is invalid as identified in the message.

Recommended Response Action

Enter a valid value and retry the operation. For information about valid values, see the Redfish Users Guide available on the support site.

Category

Audit (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS446

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The requested operation cannot be completed because of an internal error.
Detailed Description: The requested operation cannot be completed because of an internal error.
Recommended Response Action: Retry the operation after a few minutes. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS447

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create the job because the time arg1 entered is invalid.

Arguments

arg1 = Value

Detailed Description

The job cannot be created because the time entered is invalid.

Recommended Response Action

Enter Time in the String format, and then retry the operation For example, YYYY-MM-DDTHH:MM:SS(+/-)HH:MM. Make sure the input TimeZone matches with iDRAC TimeZone. Make sure the time entered is greater than the current iDRAC time. For more information about recommended Time format, see the iDRAC Redfish Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS448

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The job cannot be created because the MaintenanceWindowDurationInSeconds value entered is invalid.
Detailed Description: The job cannot be created because the MaintenanceWindowDurationInSeconds value entered is less than 300 seconds of MaintenanceWindowStartTime value.
Recommended Response Action: Enter a MaintenanceWindowDurationInSeconds value that is greater than 300 seconds of the MaintenanceWindowStartTime value.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS449

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Active Directory objects DCLookupEnable or GCLookupEnable cannot be enabled because IPv4.DNS1, IPv4.DNS2, IPv6.DNS1, or IPv6.DNS2 is not configured.
Detailed Description: The Active Directory objects DCLookupEnable or GCLookupEnable cannot be enabled, because IPv4.DNS1, IPv4.DNS2, IPv6.DNS1 or IPv6.DNS2 is not configured.
Recommended Response Action: Configure IPv4.DNS1, IPv4.DNS2, IPv6.DNS1 or IPv6.DNS2 by using Redfish OEM Attributes Patch operation, and retry the operation. For more information about configuring the attributes, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS450

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the property arg1 is not supported.

Arguments

arg1 = property name

Detailed Description

The operation cannot be completed because, the property identified in the message is not supported.

Recommended Response Action

Remove the property from the request body and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS451

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the query parameter arg1 is not supported.

Arguments

arg1 = query type

Detailed Description

The operation cannot be completed because the query parameter entered as identified in the message is not supported.

Recommended Response Action

Enter a valid query parameter and retry the operation. For information about supported query parameters, see the iDRAC Users Manual available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS452

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The "request body" element is not allowed for the action: arg1.

Arguments

arg1 = action name

Detailed Description

The "request body" element is not allowed for the action identified in the message.

Recommended Response Action

Delete the "request body" element and retry the operation. For more information about recommended formats, see the Schema and Redfish Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS453

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to perform the insert operation because the image file arg1 is of a different type than the insert operation supported by arg2.

Arguments

arg1 = image file name
arg2 = instance name

Detailed Description

The insert operation cannot be performed because the image file is of a different type than the insert operation supported by the instance identified in the message.

Recommended Response Action

Do the following the retry the operation: 1) Check if the image file is valid and of support type. iDRAC supports only the .ISO files for CD and .IMG file for removable drive. 2) Check if the action is performed on the correct device.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS454

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the requested operation because the attribute entered is not supported by implementation.
Detailed Description: The requested operation cannot be performed because the attribute entered is not supported by implementation.
Recommended Response Action: Enter the implementation supported attribute in the recommended format and retry the operation. For information about the recommended formats, see the iDRAC Redfish API Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS455

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to change the current system configuration because the attributes entered already exist.
Detailed Description: The current system configuration cannot be changed because the attributes entered already exist.
Recommended Response Action: Enter the system configuration attributes other than the existing one. For more information about viewing the current system configuration, see the iDRAC with Lifecycle Controller Redfish API Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS456

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to process requested query arg1 because the value entered arg2 is not supported by the implementation.

Arguments

arg1 = query parameter
arg2 = value

Detailed Description

The requested query cannot be processed because the query parameter contains a value not supported by the implementation.

Recommended Response Action

Remove the element identified in the message and retry the operation. For information about supported queries, see the Redfish Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS457

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the value entered for the query parameter arg1 is invalid.

Arguments

arg1 = query parameter

Detailed Description

The operation cannot be completed because the value entered for the query parameter is invalid.

Recommended Response Action

Enter a valid value for the query parameter and retry the operation. For information about recommended values for the query parameters, see the Redfish Users Guide available on the support site.

Category

Audit (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS458

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to Process the request because the value entered for the parameter arg1 is not supported by the implementation.

Arguments

arg1 = parameter

Detailed Description

The request cannot be processed because the value entered for the parameter identified in the message is not supported by the implementation.

Recommended Response Action

Correct the value of the parameter identified in the message and retry the operation. For information about supported values, see the Redfish Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS459

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set the Chassis Service Tag because the Chassis Service Tag is already set.
Detailed Description: The Chassis Service Tag cannot be set because the Chassis Service Tag is already set. The Chassis Service Tag can be set only once.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS460

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the necessary telemetry operation because the Telemetry feature is disabled.
Detailed Description: The necessary telemetry operation cannot be performed because the Telemetry feature is disabled.
Recommended Response Action: Enable Telemetry feature to proceed on any telemetry operations. For more information about enabling Telemetry, see the iDRAC User Guide and RACADM CLI Guide available on the support site.
Category: Audit (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS461

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the necessary telemetry operation because the server does not have the required Telemetry Datacenter license.
Detailed Description: The necessary telemetry operation cannot be performed because the server does not have the required Telemetry Datacenter license.
Recommended Response Action: Enable Telemetry Data center license. For more information about enabling Telemetry on 15G and later PowerEdge servers, see the iDRAC Users Guide and RACADM CLI Guide available on the support site.
Category: Audit (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS462

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate the telemetry report because the telemetry report is disabled.
Detailed Description: The necessary telemetry operation cannot be performed because the telemetry report is disabled.
Recommended Response Action: Enable the Telemetry report . For more information about enabling Telemetry report on 15G and later PowerEdge servers, see the iDRAC Users Guide and RACADM CLI Guide available on the support site.
Category: Audit (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS463

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to configure the job because properties arg1 and arg2 entered are mutually exclusive.

Arguments

arg1 = property 1
arg2 = property 2

Detailed Description

The job cannot be configured because properties entered are mutually exclusive as identified in the message.

Recommended Response Action

Enter properties that are not mutually exclusive and reconfigure the job. For information about mutually exclusive properties, see the iDRAC Redfish API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS464

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate the telemetry report because the CPU Register report is currently not available.
Detailed Description: The telemetry report cannot be generated because the CPU Register report is currently not available.
Recommended Response Action: A CPU Register report is generated only when a CPU error occurs. Therefore, retry the operation when a CPU error occurs and the CPU Register report is made available.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS465

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to add the new BIOS HTTP certificate because the currently installed BIOS version does not support adding a new BIOS HTTP certificate.
Detailed Description: The new BIOS HTTP certificate cannot be added because the currently installed BIOS version does not support adding a new BIOS HTTP certificate.
Recommended Response Action: Update the BIOS to the latest version and retry the operation. For information about updating a BIOS version by using the iDRAC GUI, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS466

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the certificate because the Transport Layer Security (TLS) authentication mode does not support the import operation for the specified HTTP device instance.
Detailed Description: The certificate cannot be imported because the Transport Layer Security (TLS) authentication mode does not support the import operation for the specified HTTP device instance.
Recommended Response Action: Change the Transport Layer Security (TLS) authentication mode to one-way, and then retry the operation. For information about changing the TLS authentication mode on the iDRAC GUI, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS467

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the certificate because the BIOS HTTP certificate collection pool has reached its maximum value.
Detailed Description: The certificate cannot be imported because the BIOS HTTP certificate collection pool has reached its maximum value.
Recommended Response Action: Delete one or more certificates from the BIOS HTTP certificate collection pool, and then retry the operation. For information about deleting certificates from the BIOS HTTP collection by using the iDRAC GUI, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS468

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the Authorization request header is present in the request.
Detailed Description: The operation cannot be successfully completed because the Authorization request header is found in the request.
Recommended Response Action: Make sure that the Authorization request header is not included and retry the operation. For information about the necessary headers, see the Redfish specification and Redfish Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS469

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create the telemetry subscription because the subscription limit is more than the implementation limit.
Detailed Description: The telemetry subscription cannot be created because the subscription limit is more than the implementation limit.
Recommended Response Action: Do the following and retry the operation: 1) Reduce the number of other telemetry subscriptions. 2) Increase the limit of simultaneous subscriptions, if supported. For more information about telemetry subscriptions in iDRAC, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS470

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create telemetry subscription because the properties OriginResources and MetricReportDefinitions cannot be used together for creating telemetry subscription.
Detailed Description: The telemetry subscription cannot be created because the properties OriginResources and MetricReportDefinitions cannot be used together in the payload for creating telemetry subscription.
Recommended Response Action: Do the following and retry the operation. 1) Remove the property OriginResources from the payload. 2) Add only the new property - MetricReportDefinitions for creating telemetry subscription.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS472

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the memory size of the metric report created by the payload exceeds the implementation size.
Detailed Description: The operation cannot be completed because the memory size of the metric report created by the payload exceeds the implementation size.
Recommended Response Action: Reduce the payload size and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS473

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the arg1 operation because the method is not supported on this instance of the arg2 resource.

Arguments

arg1 = method name
arg2 = resource Name

Detailed Description

The operation identified in the message cannot be completed because the method is not supported on this instance of the resource.

Recommended Response Action

Select an instance of the resource that supports the operation, and retry the operation. For more information, see the iDRAC Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS474

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set the password because the password entered does not comply to the Security Strengthen Policy standards.
Detailed Description: The password cannot be set because the password entered does not comply to the Security Strengthen Policy standards.
Recommended Response Action: Make sure that the password complies to the Security Strengthen Policy standards, and then retry the operation. For information about requirements of Security Strengthen Policy, see the iDRAC Users Guide.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS475

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because there are duplicate values in the list entered for the property arg1.

Arguments

arg1 = property

Detailed Description

The operation cannot be completed because the values entered for the property identified in the message is not supported.

Recommended Response Action

Enter a valid value for the property in the request body and retry the operation. For information about valid values, see the iDRAC Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*

Applicable Event or Alert Types

CMC—Not Applicable

SYS476

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because another Metric Report Definition upload is in progress.
Detailed Description: Unable to complete the operation because another Metric Report Definition upload is in progress.
Recommended Response Action: Wait for the Metric Report Definition upload operation to complete and retry.
Category: Configuration (SYS = System Info)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS477

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Proof of possession challenge failed.
Detailed Description: Proof of possession challenge failed.
Recommended Response Action: Proof of possession challenge failed. Verify that the client is sending proper values and retry. If the problem persists then call support.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS478

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to upload the certificate because the certificate type is not supported.
Detailed Description: The certificate cannot be uploaded because the uploaded certificate format type is not supported.
Recommended Response Action: Upload the certificate in PEM format, and then retry the operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS479

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: There are insufficient privileges for the account or credentials associated with the current session to perform the requested operation.
Detailed Description: Indicates that the credentials associated with the established session do not have sufficient privileges for the requested operation.
Recommended Response Action: Either abandon the operation or change the associated access rights and resubmit the request if the operation failed.
Category: Configuration (SYS = System Info)
Severity: Critical
Trap/EventID: 10625
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS480

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the length of arg1 string is more than the permitted length of arg2.

Arguments

arg1 = property
arg2 = limitValue

Detailed Description

The operation cannot be completed because the length of the string is more than the permitted length as identified in the message.

Recommended Response Action

Enter a string whose length is equal to or less than the value indicated in the message, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS481

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The property Metrics value exceeds the list length of arg1.

Arguments

arg1 = length

Detailed Description

The operation cannot be completed because the list length of the property is more than the permitted length as identified in the message.

Recommended Response Action

Enter a property name whose list length is equal to or less than the value indicated in the message, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS482

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the MetricReportDefinition arg1 already exists.

Arguments

arg1 = metricreportdefinition

Detailed Description

The operation cannot be completed because the MetricReportDefinition identified in the message already exists.

Recommended Response Action

Enter a unique MetricReportDefinitionIdand retry the operation. For information about permitted characters for the MetricReportDefinition Id,see the User Guideor API Guide on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS483

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The string arg1 is under the length limit arg2.

Arguments

arg1 = property
arg2 = value

Detailed Description

The property within the message under the string minimum length described in the message.

Recommended Response Action

Resubmit the request with an appropriate string length.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS484

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the length of arg1 string is not within the recommended range of arg2 and arg3.

Arguments

arg1 = property
arg2 = minValue
arg3 = maxValue

Detailed Description

The operation cannot be completed because the length of the string is not within the range as identified in the message.

Recommended Response Action

Enter a string whose length is within the range indicated in the message, and then retry the operation. For information about permitted character length, see the product-specific User Guideor API Guide on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS485

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because MetricReportHeartBeatInterval is not within an acceptable range. The minimum value shall match the RecurrenceInterval property value. The maximum range is 24 hours.
Detailed Description: The property within the message is limited to the bounds referred in the message.
Recommended Response Action: Enter a valid value for the property in the request body and retry the operation. For information about valid values, see the product-specific User Guide or API Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS487

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the RecurrenceInterval value entered for MetricReportDefinitionType, Periodic, is less than arg1.

Arguments

arg1 = value

Detailed Description

The operation cannot be completed because the length of the RecurrenceInternal value is less than the minimum value identified in the message.

Recommended Response Action

Enter a RecurrenceInternal value that is equal to or greater than the value recommended in the message. For information about permitted value of a RecurrenceInterval, see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS488

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because either the MetricReportHeartbeatInterval value entered is not equal to or greater than RecurrenceInterval value, or the SuppressRepeatedMetricValue is not set to True.
Detailed Description: MetricReportHeartBeatInterval has a few requirements. 1) SuppressRepeatedMetricValue property must be enabled. 2) The MetricReportHeartbeatInterval must have a value of RecurrenceInterval or greater. 3) If MetricReportHeartbeatInterval is desired to be disabled. The value shall be set to PT0S.
Recommended Response Action: Enter a MetricReportHeartbeatInterval value that is equal to or greater than the RecurrenceInterval value recommended in the message. For information about permitted characters in MetricReportHeartbeatInternval,see the product-specific User Guide or API Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS489

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the MetricReportDefinitionType, OnChange requires the following- clearing RecurrenceInterval and MetricReportHeartbeatInterval, setting SuppressRepeatedMetricValue to true. ReportTimeSpan to arg1 or greater.

Arguments

arg1 = value

Detailed Description

The OnChange MetricReportDefinition requires (1) RecurrenceInterval and MetricReportHeartbeatInterval to be cleared (2)SuppressRepeatedMetricValue to be true (3) ReportTimeSpan to be the value in the message or greater.

Recommended Response Action

Enter valid values for the properties in the request body and retry the operation. For information about valid values,see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS490

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the MetricReportDefinitionType, Onrequest requires RecurrenceInterval to be clear and ReportTimeSpan to be arg1 or greater.

Arguments

arg1 = time

Detailed Description

The operation cannot be completed because Onrequest require RecurrenceInterval to be cleared and ReportTimeSpan to be greater the value in the message.

Recommended Response Action

Enter valid values for the properties in the request body and retry the operation. For information about valid values, see the product-specific User Guide or API Guide available on the support site.

Category

Audit (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS491

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the CollectionDuration and CollectionFunction must be set at the same time. CollectionDuration shall be arg1 or greater.

Arguments

arg1 = value

Detailed Description

The operation cannot be completed because the CollectionDuration and CollectionFunction attributes must be set at the same time.

Recommended Response Action

Do the following and retry the operation: 1) Set the CollectionFunction and Collection Duration attributes at the same time. 2) Enter a CollectionDuration value that is equal to greater than <value>.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS492

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the MetricReportDefinition arg1 does not exist.

Arguments

arg1 = MetricReportDefinitionName

Detailed Description

The operation cannot be completed because the MetricReportDefinition identified in the message does not exist.

Recommended Response Action

Include URIs with available MetricReportDefinitionname.For information about availableURIs view the property members at URI /redfish/v1/TelemetryService/MetricReportDefinitions.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS493

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the maximum number of MetricReportDefinitions arg1 is already created.

Arguments

arg1 = maxNum

Detailed Description

The operation cannot be completed because the maximum number of MetricReportDefinitions identified in the message is already created.

Recommended Response Action

Delete a MetricReportDefinitions and retry the operation. Issue a DELETE HTTP method to /redfish/v1/TelemetryService/MetricReportDefinitions/<ID>.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS494

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The request failed due to an internal service error. The service is still operational.
Detailed Description: The request failed due to an internal service error. The service is still operational.
Recommended Response Action: Indicates that the request failed for an unknown internal error but that the service is still operational.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS495

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 was disabled because the property arg2 was cleared.

Arguments

arg1 = property
arg2 = name

Detailed Description

The property is disabled because the property identified in the message is cleared.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS496

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the metric report arg1 does not exist.

Arguments

arg1 = reportName

Detailed Description

The operation cannot be completed because the metric report identified in the message does not exist.

Recommended Response Action

Enter a valid URI and retry the operation. For information about URIs view the member array at URI/redfish/v1/TelemetryService/MetricReports.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS497

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Telemetry feature is successfully disabled.
Detailed Description: The Telemetry feature is successfully disabled on the product.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS498

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Telemetry feature is successfully enabled.
Detailed Description: The Telemetry feature is successfully enabled on the product.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS499

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Metric Report arg1 is successfully deleted from /redfish/v1/TelemetryService/MetricReports.

Arguments

arg1 = metricreport

Detailed Description

The metric report identified in the message is successfully deleted from /redfish/v1/TelemetryService/MetricReports.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS501

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create the metric report definition arg1.

Arguments

arg1 = metricReportDefinitionName

Detailed Description

The metric report definition in the message can not be created. See the product-specific User Guide or API Guide available on the support site. It provides configuration details for metric report definitions.

Recommended Response Action

Retry creating the trigger. For information about metric report definition, see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS502

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to update the metric report definition arg1.

Arguments

arg1 = metricReportDefinitionName

Detailed Description

The metric report definition in the message can not be updated. See the product-specific User Guide or API Guide available on the support site. It provides configuration details for metric report definitions.

Recommended Response Action

Retry updating the trigger. For information about metric report definition, see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS503

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete the metric report definition arg1.

Arguments

arg1 = metricReportDefinitionName

Detailed Description

The metric report definition in the message can not be deleted. See the product-specific User Guide or API Guide available on the support site. It provides configuration details for metric report definitions.

Recommended Response Action

Retry creating the trigger. For information about metric report definition, see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS504

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Metric Report Definition arg1 is successfully created.

Arguments

arg1 = mrd

Detailed Description

The metric report definition identified in the message is successfully created.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS505

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Metric Report Definition arg1 is successfully updated.

Arguments

arg1 = mrd

Detailed Description

The metric report definition identified in the message is successfully updated.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS506

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Metric Report Definition arg1 is successfully deleted.

Arguments

arg1 = mrd

Detailed Description

The metric report definition identified in the message is successfully deleted.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS508

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete the trigger arg1.

Arguments

arg1 = trigger

Detailed Description

The Trigger in the message can not be deleted. See the product-specific User Guide or API Guide available on the support site. It provides configuration details for triggers.

Recommended Response Action

Retry deletingthe trigger. For information about triggers, see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS509

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create the trigger arg1.

Arguments

arg1 = trigger

Detailed Description

The Trigger in the message can not be created. see the product-specific User Guide or API Guide available on the support site. It provides configuration details for triggers.

Recommended Response Action

Retry creatingthe trigger. For information about triggers, see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS510

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to update the trigger arg1.

Arguments

arg1 = trigger

Detailed Description

The Trigger in the message can not be updated. See the product-specific User Guide or API Guide available on the support site. It provides configuration details for triggers.

Recommended Response Action

Retry updating the trigger. For information about triggers, see the product-specific User Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS511

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Trigger arg1 is successfully deleted.

Arguments

arg1 = trigger

Detailed Description

The trigger identified in the message is successfully deleted.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS512

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Trigger arg1 is successfully created.

Arguments

arg1 = trigger

Detailed Description

The trigger identified in the message is successfully created.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS513

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Trigger arg1 is successfully updated.

Arguments

arg1 = trigger

Detailed Description

The trigger identified in the message is successfully updated.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS514

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the request. The arg1 max allowed Trigger limit has been reached.

Arguments

arg1 = maxtrigger

Detailed Description

The operation cannot be completed because the maximum number of Triggers identified in the message is already created.

Recommended Response Action

Delete a Trigger and retry the operation. Issue a DELETE HTTP method to /redfish/v1/TelemetryService/Triggers/<ID>.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS515

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the Trigger arg1 does not exist.

Arguments

arg1 = TriggerName

Detailed Description

The operation cannot be completed because the Trigger identified in the message does not exist.

Recommended Response Action

Include URIs with available trigger name. For information about available URIs view the property members at URI /redfish/v1/TelemetryService/Triggers.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS516

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because there are more than one filter types mentioned in the payload.
Detailed Description: The operation cannot be completed because there are more than one filter types mentioned in the payload.
Recommended Response Action: Do not enter different filter types in payload. For information about supported filter types, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS517

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the values entered for the property arg1 are exceeding the maximum permitted value of arg2 supported by the service.

Arguments

arg1 = property
arg2 = thresholdValue

Detailed Description

The operation cannot be completed because the values entered for the property are exceeding the maximum permitted value of supported by the service.

Recommended Response Action

Enter a list of value that does not exceed the permitted limit. For information about supported filter types, see the iDRAC Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS518

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC is currently unable to display any information because data sources are unavailable.
Detailed Description: iDRAC is currently unable to display any information because data sources are unavailable.
Recommended Response Action: Wait for the data to be available and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS519

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC is currently unable to display some information because either data sources are unavailable, or data may be stale or incomplete.
Detailed Description: iDRAC is currently unable to display some information because either data sources are unavailable, or data may be stale or incomplete.
Recommended Response Action: Wait for the data to be available and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS520

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because duplicate values are entered for the property arg1.

Arguments

arg1 = property

Detailed Description

The operation cannot be completed because duplicate values are entered in the for property identified in the message.

Recommended Response Action

Make sure that the values are not reentered, and then retry the operation. For more information about actualvalues, see the iDRAC Users Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS521

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The operation cannot be completed because the Trigger arg1 already exists.

Arguments

arg1 = trigger

Detailed Description

The operation cannot be completed because the Trigger identified in the message already exists.

Recommended Response Action

Enter a unique Trigger ID and retry the operation. For information about permitted characters for the Trigger ID, see the User Guide or API Guide on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS522

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to access the arg1 Metric Report because the MetricReportDefinition arg2 is either disabled or is not configured with LogToMetricReportsCollection.

Arguments

arg1 = mr
arg2 = mrd

Detailed Description

The Metric Report is not available in the path /redfish/v1/TelemetryService/MetricReports because the corresponding Metric Report Definitions property MetricReportDefinitionEnabled is disabled or/and the ReportActions does not have LogToMetricReportsCollection.

Recommended Response Action

Configure MetricReportDefinition in the message with MetricReportDefinitionEnabled set to true and LogToMetricReportsCollection included in the ReportActions list.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS523

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Telemetry report collection operation is started.
Detailed Description: The Telemetry report collection operation is started.
Recommended Response Action: No response required.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS524

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Telemetry report collection operation is completed.
Detailed Description: The Telemetry report collection operation is completed.
Recommended Response Action: No response required.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS525

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform SSO because the SSO configuration is not complete.
Detailed Description: The SSO operation failed because of incomplete configuration.
Recommended Response Action: Make sure the SSO configuration is complete.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS526

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation is successfully completed. The host server needs a restart.
Detailed Description: The operation is successfully completed. The configuration changes will become effective after restarting the host server next time.
Recommended Response Action: No response action is required. However, to make them immediately effective, restart the host server.
Category: Audit (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS527

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create a trigger because either the trigger properties are not specific to the trigger type or more than one trigger type property is entered.
Detailed Description: The operation cannot be completed because the trigger properties are not specific to the type of trigger.
Recommended Response Action: Enter trigger properties that are specific to the type of trigger specified in the MetricType property, and then retry the operation. For information about triggers,see the product-specific Users Guide or API Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS528

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create a trigger because the necessay trigger properties arg1,arg2, and arg3 are not entered for the arg4.

Arguments

arg1 = prop1
arg2 = prop2
arg3 = prop3
arg4 = triggername

Detailed Description

The operation cannot be completed because the necessary trigger properties are not entered as identified in the message.

Recommended Response Action

Enter trigger properties that are specific to the type of trigger specified in the MetricType property, and then retry the operation. For information about triggers,see the product-specific Users Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS529

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create a trigger because the necessary trigger properties, arg1 and arg2, are not entered for the arg3.

Arguments

arg1 = prop1
arg2 = prop2
arg3 = triggername

Detailed Description

The operation cannot be completed because the necessary trigger properties are not entered as identified in the message.

Recommended Response Action

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS530

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create the trigger because invalid trigger properties, arg1 and arg2, are entered for the trigger arg3.

Arguments

arg1 = prop1
arg2 = prop2
arg3 = triggerName

Detailed Description

The operation cannot be completed because the necessary trigger properties are not entered as identified in the message.

Recommended Response Action

Enter trigger properties that are specific to the type of trigger specified in the MetricType property, and then retry the operation. For information about triggers, see the Users Guide or API Guide pertaining to the iDRAC or Skylynx products.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS531

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create the metric report definition because attributes for both the metric properties and arg1 are not entered.

Arguments

arg1 = propertyName

Detailed Description

The operation cannot be completed because MetricProperties is set to a list of values and FQDD or Source is set to a value.

Recommended Response Action

Make sure to enter the attribute for at least one of either FQDD or source, or metric properties.For information about defining metric reports, see the Users Guide or API Guide pertaining to the iDRAC orSkylynxproducts.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility

SYS533

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the wildcard arg1 in the wildcards property is not available in at least one metric property.

Arguments

arg1 = wildcardName

Detailed Description

Metric properties are allowed to have one or more wildcards, which are a string wrapped with { and }. The operation cannot be completed because the wildcard defined in the wildcards property is not entered in at least one Metricproperty.

Recommended Response Action

Enter a valid wildcard at least one metricproperty,and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS534

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the property value in path Wildcards to Values have mismatched with the MetricProperty arg1.

Arguments

arg1 = metricPropertyName

Detailed Description

The wildcards are expanded in the metricproperty based on the value index. Therefore wildcards listed in a metricproperty should have the same number of values defined.

Recommended Response Action

Update the Wildcards property Values to have the same array length and retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS535

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the property value in path Wildcards to Values is empty for Wildcard arg1.

Arguments

arg1 = wildcardName

Detailed Description

The operation cannot be completed because no strings are entered in the wildcard identified in the message.

Recommended Response Action

Delete the wildcard identified in the message or enter at least one string for the wildcard, and then retry the operation.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS536

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the list length of the property arg1 entered is less than the minimum acceptable length of arg2.

Arguments

arg1 = propertyName
arg2 = lengthValue

Detailed Description

The operation cannot be completed because the list length of the property entered is less than the minimum acceptable length as identified in the message.

Recommended Response Action

Do one of the following and retry the operation: 1) Remove the property name identified in the message. 2) Make sure that list length is equal to or less than the specified value.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS537

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Generate CSR operation is taking longer duration than expected. Wait few minutes for the operation to complete and perform the Download CSR operation. For more information, see the iDRAC Redfish API Guide available on the support site.
Detailed Description: The Generate CSR operation is taking longer duration than expected. Wait few minutes for the operation to complete and perform the Download CSR operation. For more information, see the iDRAC Redfish API Guide available on the support site.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS538

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The metric definition arg1 is successfully created.

Arguments

arg1 = metricDefinitionName

Detailed Description

The metric definition identified in the message is successfully created.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS539

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The metric definition arg1 is deleted.

Arguments

arg1 = metricDefinitionName

Detailed Description

The metric definition identified in the message is deleted.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS540

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create the metric definition arg1 because of internal issue.

Arguments

arg1 = metricDefinitionName

Detailed Description

The metric definition identified in the message cannot be created because of internal issue.

Recommended Response Action

Retry creating the metric definition. For information about metric definition, see the product-specific Users Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS541

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete the metric definition arg1 because of internal issue.

Arguments

arg1 = metricDefinitionName

Detailed Description

The metric definition identified in the message cannot be deleted because of internal issue.

Recommended Response Action

Retry deleting the metric definition. For information about metric definition, see the product-specific Users Guide or API Guide available on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS542

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete the pre-defined Metric Definition arg1 because a pre-defined Metric Definition cannot be deleted.

Arguments

arg1 = metricDefinitionName

Detailed Description

The pre-defined metric definition identified in the message cannot be deleted.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS543

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the maximum number of MetricDefinitions arg1 are already created.

Arguments

arg1 = maxNum

Detailed Description

The operation cannot be completed because the maximum number of MetricDefinitions identified in the message are already created.

Recommended Response Action

Delete a MetricDefinition and retry the operation. Issue a DELETE HTTP method to /redfish/v1/TelemetryService/MetricDefinitions/<ID>.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS544

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation cannot be successfully completed because the EnableMetricInjection attribute is disabled.
Detailed Description: Unable to complete the operation because the EnableMetricInjection attribute is disabled.
Recommended Response Action: Make sure that the Telemetry. 1) EnableMetricInjection attribute is set to Enabled using other iDRAC interfaces, and then retry the operation. For example, racadm set idrac.Telemetry.EnableMetricInjection Enabled.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS545

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the operation is allowed from only OS application through the inband interface.
Detailed Description: The operation cannot be completed because the operation is allowed from only OS application through the inband interface.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS546

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the Metric Definition arg1 already exists.

Arguments

arg1 = MetricDefinitionName

Detailed Description

The operation cannot be completed because the Metric Definition identified in the message already exists.

Recommended Response Action

Enter a unique MetricDefinition ID and retry the operation. For information about permitted characters in a MetricDefinition ID, see the iDRAC Users Guide or API Guide on the support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS547

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the MetricDefinition arg1 does not exist.

Arguments

arg1 = MetricDefinitionName

Detailed Description

The operation cannot be completed because the Metric Definition identified in the message does not exist.

Recommended Response Action

Enter valid Metric Definition name in the URIs and retry the operation. For information about the available URIs, view the property members at URI /redfish/v1/TelemetryService/MetricDefinitions.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS548

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Telemetry metric injection feature is successfully disabled on the server.
Detailed Description: The Telemetry metric injection feature is successfully disabled on the server.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS549

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Telemetry metric injection feature is successfully enabled on the server.
Detailed Description: The Telemetry metric injection feature is successfully enabled on the server.
Recommended Response Action: No action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS550

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the minimum time interval between the two consecutive SubmitMetricValue requests is less than or equal to 60 seconds.
Detailed Description: Unable to complete the operation because the minimum time interval between the two consecutive SubmitMetricValue requests is less than or equal to 60 seconds.
Recommended Response Action: Ensure that the minimum time interval between the two consecutive SubmitMetricValue requests, is more than 60 seconds.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS551

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the total metric values submitted in the SubmitMetricValue attribute is more than 48.
Detailed Description: The operation cannot be completed because the total metric values submitted in the SubmitMetricValue action is more than 48.
Recommended Response Action: Make sure that the total number of metric values submitted is less than or equal to 48. For more information about SubmitMetricValue, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS552

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the timestamp of metric value in the SubmitMetricValue attribute is more than one hour compared to the system (current) time.
Detailed Description: The operation cannot be completed because the timestamp of metric value in the SubmitMetricValue attribute is more than one hour compared to the system (current) time.
Recommended Response Action: Make sure that the timestamp of metric value in the SubmitMetricValue attribute is within one hour of the system (current) time. For more information about SubmitMetricValue, see the iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS553

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create the first OAuth2 instance using the POST operation on the ExternalAccountProviders Collection URI because no OAuth2 instance is configured.
Detailed Description: The first OAuth2 instance cannot be created by using a POST on the ExternalAccountProviders Collection URI because no OAuth2 instance is configured. As per the DMTF specification and schemas, the first OAuth2 instance can be configured only by performing a PATCH on the AccountService resource instance. After creating the first OAuth2 instance, you can create additional OAuth2 instances by performing a POST operation on the ExternalAccountProviders Collection Resource.
Recommended Response Action: Configure the first OAuth instance by performing a PATCH operation on the relevant properties of the OAuth2 property in the AccountService resource instance.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS554

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Redfish EventService feature is partially enabled because the IPMILan.1.AlertEnable property is disabled in the URI /redfish/v1/Managers/iDRAC.Embedded.1/Oem/Dell/DellAttributes/iDRAC.Embedded.1.
Detailed Description: The Redfish EventService feature is partially enabled because the IPMILan.1.AlertEnable property is disabled in the URI /redfish/v1/Managers/iDRAC.Embedded.1/Oem/Dell/DellAttributes/iDRAC.Embedded.1.
Recommended Response Action: Enable the IPMILan.1.AlertEnable property in the following URI: /redfish/v1/Managers/iDRAC.Embedded.1/Oem/Dell/DellAttributes/iDRAC.Embedded.1.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS555

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Secure-Feature-Token is successfully used on the iDRAC.
Detailed Description: The Secure-Feature-Token is successfully used on the iDRAC.
Recommended Response Action: No response action is required.
Category: Audit (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS556

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Secure Feature Token applied to the URL arg1 is invalid.

Arguments

arg1 = URLName

Detailed Description

The Secure Feature Token applied to the URL is invalid as identified in the message.

Recommended Response Action

Create a valid Secure Feature Token and retry the HTTP request with the URL inside the message.

Category

Audit (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS557

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The certificate signing operation is taking more time. Wait for a few minutes.
Detailed Description: The certificate signing operation is taking more time. Wait for a few minutes.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*
Applicable Event or Alert Types: CMC—Not Applicable

SYS558

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to add the firmware inventory because of internal issue identified in arg1.

Arguments

arg1 = error code

Detailed Description

The firmware inventory operation cannot be completed because of internal issue identified in the error code identified in the message. Share the SupportAssist log data and the debug logs option enabled with your service provider.

Recommended Response Action

Do the following: a) Power off the server and disconnect the power cord. b) Wait for 10 seconds, reconnect the power cord, power on the server, wait for iDRAC to be fully ready and device to be available in the firmware inventory. c) If the issue persists, update iDRAC firmware to the latest version, and then retry the operation. d) If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SYS = System Info)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS559

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Data on all the DPUs are reset.
Detailed Description: Data on all the DPUs are reset.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS560

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to reset data for one or more DPUs.
Detailed Description: The DPU data cannot be reset.
Recommended Response Action: Do the following and retry the operation; 1) Review the Lifecycle Controller (lifecycle?) log for related update configuration or collection job errors, 2) Reset the DPU and retry the System Erase operation, 3) If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: System Health (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS561

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The firmware are successfully reinstalled. For more information, see the Job Queue.
Detailed Description: The firmware are successfully reinstalled. For more information, see the Job Queue.
Recommended Response Action: No response action is required. However, if necessary, review the Lifecycle log data for information about update configuration or collection job errors. If any issues are listed then do the following: 1) Reset iDRAC and retry the upgrade operation. 2) If the issue persists, install any other necessary firmware and retry the operation, 3) If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS562

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to authenticate the arg1 firmware payload because either the payload is not signed or the payload is signed with an incorrect SSH key.

Arguments

arg1 = ComponentName

Detailed Description

The component firmware identified in the message cannot be authenticated because either the payload is not signed or the payload is signed with an incorrect SSH key.

Recommended Response Action

Download the component firmware Update Package from the support site and retry the operation.

Category

Updates (SYS = System Info)

Severity

Warning

Trap/EventID

6530

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS563

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to power on the server because one or more iDRAC jobs are in pending state.
Detailed Description: The server cannot be powered on because one or more iDRAC jobs are in pending state.
Recommended Response Action: Either wait for the iDRAC jobs to get completed or delete the jobs and then restart iDRAC.
Category: Updates (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS564

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The System Erase operation cannot be performed on the Data Processing Unit (DPU) because the DPU is not available in the host system.
Detailed Description: The System Erase operation cannot be performed on the Data Processing Unit (DPU) because the DPU is not available in the host system.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS565

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The memory module temperature has exceeded the warning threshold value.
Detailed Description: The memory module temperature has exceeded the warning threshold value.
Recommended Response Action: Do the following: 1) Verify if the system inlet temperature is within the operational range. 2) If the fans are not rotating at maximum speed, apply the Fan Max Offset setting in iDRAC. 3) If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: System Health (SYS = System Info)
Severity: Warning
Trap/EventID: 2434
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Not Applicable

SYS566

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The memory module temperature has returned to its normal value.
Detailed Description: The memory module temperature has returned to its normal value.
Recommended Response Action: No response action is required.
Category: System Health (SYS = System Info)
Severity: Informational
Trap/EventID: 2435
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Not Applicable

SYS567

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The BIOS time is successfully set on the host server.
Detailed Description: The BIOS time is successfully set on the host server.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS568

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to set the BIOS time because: arg1.

Arguments

arg1 = runtime msg

Detailed Description

The BIOS Set Time job failed because of the reason identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS569

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to update the firmware of arg1 because of a timeout issue while waiting for the device to update its backup firmware copy.

Arguments

arg1 = firmwareType

Detailed Description

The firmware identified in the message cannot be updated because of a timeout issue while waiting for the device to update its backup firmware copy.

Recommended Response Action

Perform an AC Power Cycle operation and retry the firmware update operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SYS = System Info)

Severity

Critical

Trap/EventID

2433

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS570

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The WriteProtect mode cannot be disabled because the iDRAC System Lockdown mode is enabled.
Detailed Description: The WriteProtect mode cannot be disabled because the iDRAC System Lockdown mode is enabled.
Recommended Response Action: Make sure that the SystemLockdown attribute is set to Disabled and then retry the operation. For information about enabling or disabling the Lockdown mode, see the relevant iDRAC Users Guide available on the support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS571

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to arg1 the WriteProtect mode because of an internal backend issue while processing the request.

Arguments

arg1 = actionName

Detailed Description

The status of the WriteProtect mode cannot be changed because of an internal backend issue while processing the request.

Recommended Response Action

Perform an AC Power Cycle operation and retry the write-protect operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SYS = System Info)

Severity

Critical

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS572

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because SystemRepurposeControl is set to Disabled.
Detailed Description: The operation cannot be completed because the SystemRepurposeControl attribute is disabled.
Recommended Response Action: Make sure that the SystemRepurposeControl attribute - iDRAC.Embedded.1#Security.1#SystemRepurposeControl is set to Enabled and then retry the operation. Refer to the system erase feature within the iDRAC User Guide and iDRAC Security Configuration Guide for more information.
Category: Updates (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS573

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The device is starting the backup firmware copy operation of the arg1 firmware. Do not initiate any update or power related operations until the host device is powered on for at least 12 minutes.

Arguments

arg1 = firmware type

Detailed Description

The device has started the backup firmware copy operation for the firmware type identified in the message. The backup firmware copy operation is initiated during the firmware update operation to update the inactive partition.

Recommended Response Action

No response action is required.

Category

Updates (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS574

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The device has completed the backup firmware copy operation of the arg1 firmware.

Arguments

arg1 = firmware type

Detailed Description

The device has completed the backup firmware copy operation for the firmware type identified in the message.

Recommended Response Action

No response action is required.

Category

Updates (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS8500

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Delay Auto-throttle sent to arg1 server(s). arg2 arg3

Arguments

arg1 = number of servers
arg2 = error string
arg3 = errors

Detailed Description

The Chassis Management Controller (CMC) sent messages to delay power throttling to all capable servers in the chassis. This was done because the CMC firmware was updated or a failover was initiated. If specific server errors are shown in the message, verify that the iDRAC and Lifecycle Controller firmware versions on those servers is updated to the most current version available.

Recommended Response Action

If no errors are shown, no response is required. If errors are listed in the message, navigate to the named servers and make sure that IDRAC and Lifecycle Controller firmware versions are the latest available.

Category

Audit (SYS = System Info)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SYS8501

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The current configuration of Chassis Management Controller (CMC) components is written to a chassis configuration XML file, and then copied to the specified location.
Detailed Description: The current configuration of Chassis Management Controller (CMC) components is written to a chassis configuration XML file, and then copied to the specified location.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8502

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the chassis configuration XML file to network shares such as Network File System (NFS) or Common Internet File System (CIFS) because they are not accessible.
Detailed Description: The system configuration XML file cannot be exported to network shares such as Network File System (NFS) or Common Internet File System (CIFS) because they are not accessible.
Recommended Response Action: 1) If the file is being exported to an NFS, make sure that NFS is accessible from CMC. 2) If the file is being exported to a CIFS share, make sure that CIFS is accessible from CMC by using share access credentials with appropriate privileges.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8503

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The current chassis configuration is being collected and the chassis configuration XML file is being generated.
Detailed Description: The current chassis configuration is being collected and the chassis configuration XML file is being generated.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8504

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the chassis configuration XML file from network shares such as Network File System (NFS) or Common Internet File System (CIFS) because they are not accessible.
Detailed Description: The chassis configuration XML file cannot be imported from network shares such as Network File System (NFS) or Common Internet File System (CIFS) because they are not accessible.
Recommended Response Action: 1) If the file is being copied from an NFS share, make sure that it is accessible from CMC. 2) If the file is being copied from a CIFS share, make sure that it is accessible from CMC using the share credentials provided. Test the network share access by using the Test Network Connection method.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8505

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the chassis configuration operation because the input file for chassis configuration XML is not compliant with configuration schema.
Detailed Description: The chassis configuration import operation cannot be completed because the input file is not compliant with the chassis configuration XML schema.
Recommended Response Action: Make sure that the input file is compliant with the chassis configuration schema. For more information, see the Chassis cloning, backup, and restore with Configuration profiles white paper available on Dell TechCenter website.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8506

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Configuration changes specified in the chassis configuration XML file are successfully applied.
Detailed Description: Configuration changes specified in the chassis configuration XML file are successfully applied.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8507

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The chassis configuration XML file is imported but with some configuration changes that did not complete successfully.
Detailed Description: The chassis configuration XML file is imported but with some configuration changes that did not complete successfully. The Chassis Log contains information about the component configurations that did not complete successfully.
Recommended Response Action: Review the Chassis Log and identify the configuration changes that did not complete successfully. Retry those changes in a separate operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8508

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to successfully apply the chassis configuration XML file values.
Detailed Description: Some or all configuration actions during the import of configuration XML operation did not complete successfully. The configuration action details are logged in to the Chassis Log.
Recommended Response Action: See the Chassis Log and identify the configuration changes that did not successfully complete. Resolve any issues with the configuration XML content and retry the import operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8509

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the chassis configuration XML file from network shares such as Network File System (NFS) or Common Internet File System (CIFS) because the file does not exist on the network share.
Detailed Description: The chassis configuration XML file cannot be imported because the file does not exist on the specified network share.
Recommended Response Action: Make sure that the chassis configuration file exists on the CIFS or NFS, and then retry the import operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8510

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The chassis configuration XML input file contains unsupported DOCTYPE tags that may cause security issues.
Detailed Description: The chassis configuration XML input file contains unsupported DOCTYPE tags that may cause security issues. The XML DOCTYPE tag is not supported in chassis configuration XML files.
Recommended Response Action: Check the input XML file for DOCTYPE XML tags and delete them before retrying the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8511

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The requested changes were not applied because the current component configuration is same as the requested ones.
Detailed Description: The settings specified in the chassis configuration XML file match the current configuration for all components.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8512

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The chassis configuration XML properties are currently being applied to CMC.
Detailed Description: The chassis configuration XML properties are currently being applied to CMC.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8513

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The requested changes are not applied because the Service Tag of the Chassis Management Controller (CMC) does not match with the specified chassis configuration XML file.
Detailed Description: The requested changes are not applied because the Service Tag of the Chassis Management Controller (CMC) does not match with the specified chassis configuration XML file.
Recommended Response Action: Make sure the chassis configuration XML file selected for the operation has the same Service Tag value as the CMC the changes are being applied to.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8514

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to configure chassis because the input XML file for chassis configuration is not compliant with the XML schema.
Detailed Description: The chassis cannot be configured because the input XML file for chassis configuration is not compliant with the configuration XML schema.
Recommended Response Action: Make sure that the XML file schema used for chassis configuration is compliant with the schema defined in the Lifecycle Controller XML Schema Guide on the Tech Center support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8515

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to configure chassis because the input XML file for chassis configuration contains invalid character arg1 at line arg2.

Arguments

arg1 = character
arg2 = line number

Detailed Description

The chassis cannot be configured because the input XML file for chassis configuration is not compliant with the configuration XML schema.

Recommended Response Action

View the file in any Web browser to check for invalid characters. Delete the invalid characters and make sure that the file is a valid XML file, and is compliant with the configuration XML schema.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SYS8516

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the configuration properties of chassis because the input XML file for importing chassis configuration is not compliant with the schema nesting check parameters.
Detailed Description: The configuration properties of chassis cannot be imported because the input XML file for importing chassis configuration is not compliant with the schema nesting check parameters. Only RAID controllers can have nested Component nodes.
Recommended Response Action: Make sure that the XML file schema used for chassis configuration is compliant with the schema defined in the Lifecycle Controller XML Schema Guide on the Tech Center support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8517

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the configuration properties of chassis because the input XML file for importing chassis configuration is not valid and does not contain the XML root element.
Detailed Description: The configuration properties of chassis cannot be imported because the input XML file for importing chassis configuration is not valid and does not contain the XML root element.
Recommended Response Action: Open the file in a Web browser to check for the presence of invalid content before an expected root element. Correct the invalid content and make sure that the chassis configuration XML file is compliant to the chassis configuration schema described in the Lifecycle Controller XML Schema Guide available on the Tech Center website.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8518

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the configuration properties of chassis because the input XML file for importing chassis configuration is not valid and the XML root element is not closed.
Detailed Description: The configuration properties of chassis cannot be imported because the input XML file for importing chassis configuration is not valid and the XML root element is not closed.
Recommended Response Action: Open the file in a Web browser to check for the presence of invalid content before an expected root element. Correct the invalid content and make sure that the chassis configuration XML file is compliant with the chassis configuration schema described in the Lifecycle Controller XML Schema Guide available on the Tech Center support site.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8519

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to import the configuration properties of chassis because the input XML file for importing chassis configuration is not valid at line arg1.

Arguments

arg1 = line number

Detailed Description

The configuration properties of chassis cannot be imported because the input XML file for importing chassis configuration is not valid at line identified in the message.

Recommended Response Action

Open the input file in a Web browser to check for the presence of invalid content at the line number identified in the message. Correct the invalid content and make sure that the chassis configuration XML file is compliant with the chassis configuration schema described in the Lifecycle Controller XML Schema Guide available on the Tech Center support site.

Category

Configuration (SYS = System Info)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SYS8520

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import the configuration properties of chassis because either the input XML file for importing chassis configuration cannot be opened or is not found.
Detailed Description: The configuration properties of chassis cannot be imported because either the input XML file for importing chassis configuration cannot be opened or is not found.
Recommended Response Action: Reset the Chassis Management Controller (CMC) and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SYS8521

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 is not available in this software version.

Arguments

arg1 = Feature name

Detailed Description

The feature identified in the message is not available in the current software version.

Recommended Response Action

No response action is required.

Category

Audit (SYS = System Info)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

No alerts are applicable for this message

SYS8522

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to attach the bootstrap image file because the file is already attached.
Detailed Description: The bootstrap image file cannot be attached because the bootstrap image file is already attached.
Recommended Response Action: No response action is required.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SYS8523

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to detach because the bootstrap image file is not attached.
Detailed Description: The bootstrap image file cannot be detached because the bootstrap image file is not attached.
Recommended Response Action: Attach a valid bootstrap image file and retry the operation.
Category: Configuration (SYS = System Info)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable