Inspiron 16 5630 Service Manual

PDF

System setup options

NOTE: Depending on this computer and its installed devices, the items that are listed in this section may or may not be displayed.

Table 1. System setup options—System information menu
The following table describes the Overview menu options in the System setup program.
Overview
	BIOS Version	Displays the BIOS version number.
	Service Tag	Displays the Service Tag of the computer.
	Asset Tag	Displays the Asset Tag of the computer.
	Manufacture Date	Displays the manufacture date of the computer.
	Ownership Date	Displays the ownership date of the computer.
	Express Service Code	Displays the express service code of the computer.
	Ownership Tag	Displays the ownership tag of the computer.
	Signed Firmware Update	Displays whether the signed firmware update is enabled. Default: Enabled
	Battery	Displays the battery health information.
	Primary	Displays the primary battery.
	Battery Level	Displays the battery level.
	Battery State	Displays the battery state.
	Health	Displays the battery health.
	AC Adapter	Displays whether an AC adapter is connected. If connected, the AC adapter type.
	PROCESSOR
	Processor Type	Displays the processor type.
	Maximum Clock Speed	Displays the maximum processor clock speed.
	Minimum Clock Speed	Displays the minimum processor clock speed.
	Current Clock Speed	Displays the current processor clock speed.
	Core Count	Displays the number of cores on the processor.
	Processor ID	Displays the processor identification code.
	Processor L2 Cache	Displays the processor L2 Cache size.
	Processor L3 Cache	Displays the processor L3 Cache size.
	Microcode Version	Displays the microcode version.
	Intel Hyper-Threading Capable	Displays whether the processor is Hyper-Threading (HT) capable.
	64-Bit Technology	Displays whether 64-bit technology is used.
	MEMORY
	Memory Installed	Displays the total computer memory installed.
	Memory Available	Displays the total computer memory available.
	Memory Speed	Displays the memory speed.
	Memory Channel Mode	Displays single or dual channel mode.
	Memory Technology	Displays the technology that is used for the memory.
	DIMM A Size	Displays the memory configuration of DIMM A.
	DIMM B Size	Displays the memory configuration of DIMM B.
	DEVICES
	Panel Type	Displays the Panel Type of the computer.
	Video Controller	Displays the integrate graphics information of the computer.
	Video Memory	Displays the video memory information of the computer.
	Wi-Fi Device	Displays the Wi-Fi device installed in the computer.
	Native Resolution	Displays the native resolution of the computer.
	Video BIOS Version	Displays the video BIOS version of the computer.
	Audio Controller	Displays the audio controller information of the computer.
	Bluetooth Device	Displays whether a Bluetooth device is installed in the computer.
	LOM MAC Address	Displays the MAC address of the LAN on Motherboard (LOM)

Table 2. System setup options—Boot Configuration menu
The following table describes the Boot Configuration menu options in the System setup program.
Boot Configuration
	Boot Sequence
	Boot Mode: UEFI only	Displays the boot mode of this computer.
	Boot Sequence	Specifies the order that the BIOS searches the list of devices to find an operating system to boot. By default, ONBOARD NIC (IPV4) is selected By default, ONBOARD NIC (IPV6) is selected By default, UEFI Hard Drive is selected
	Secure Boot
	Enable Secure Boot	Enables secure boot using only validated boot software. Default: OFF
	Secure Boot Mode	Modifies the behavior of Secure Boot to allow evaluation or enforcement of UEFI driver signatures. Deployed Mode should be selected for normal operation of Secure Boot. By default, Deployed Mode is selected.
	Expert Key Management
	Enable Custom Mode	Allows the PK, KEK, db, and dbx security key databases to be modified. Default: OFF NOTE: If Custom Mode is not enabled, any changes made with respect to the keys will not be saved.
	Custom Mode Key Management	Allows for selection of key database. Save to File will save the key to a user-selected file. Replace from File will replace the current key with a key from a user-selected file. Append from File will add a key to the current database from a user-selected file. Delete will delete the selected key. Reset All Keys will reset all four keys to their default settings. By default, PK security key database is selected. By default, Save to File is selected.

Table 3. System setup options—Integrated Devices menu
The following table describes the Integrated Devices menu options in the System setup program.
Integrated Devices
	Date/Time
	Date	Sets the computer date in MM/DD/YYYY format. Changes to the date take effect immediately.
	Time	Sets the computer time in HH/MM/SS 24-hour format. You can switch between 12-hour and 24-hour clock. Changes to the time take effect immediately.
	Camera
	Enable Camera	Enables or disables the camera. By default, Enable Camera is selected.
	Audio	Enables or disables all integrated audio controller. Default: ON
	Enable Microphone	Enables or disables microphone. By default, Enable Microphone is selected.
	Enable Internal Speaker	Enables or disables internal speaker. By default, Enable Internal Speaker is selected.
	USB Configuration	Enables or disables booting from USB mass storage devices such as external hard drive, optical drive, and USB drive. By default, Enable USB Boot Support is selected.

Table 4. System setup options—Storage menu
The following table describes the Storage menu options in the System setup program.
Storage
	SATA/NVMe Operation
	SATA/NVMe Operation	Configures operating mode of the integrated storage device controller. Default: RAID On. Storage device is configured to support RAID functions. When enabled, all NVMe and SATA devices will be mapped under VMD controller. Windows RST (Intel Rapid Restore Technology) driver, or Linux kernel VMD driver must be loaded in order to boot the OS.
	Storage Interface
	Port Enablement	Enables or disables the onboard drives. Default: ON
	Drive Information	Displays the information of various onboard drives.

Table 5. System setup options—Display menu
The following table describes the Display menu options in the System setup program.
Display
	Display Brightness
	Brightness on battery power		Sets the screen brightness when the computer is running on battery power. Default: 50
	Brightness on AC power		Sets the screen brightness when the computer is running on AC power. Default: 100

Table 6. System setup options—Passwords menu
The following table describes the Passwords menu options in the System setup program.
Passwords
	Admin Password	Enables the user to set, change, or delete the administrator (admin) password. The admin password enables several security features
	System Password	Enables the user to set, change, or delete the system password.
	Internal HDD-1 Password	Enables the user to set, change, or delete the Internal HDD-1 password.

Table 7. System setup options—Update,Recovery menu
The following table describes the Update,Recovery menu options in the System setup program.
Update,Recovery
	SupportAssist OS Recovery	Enables or disables the boot flow for SupportAssist OS Recovery tool, in the event of certain system error. Default: ON
	BIOSConnect	Enables or disables cloud Service OS recovery if the main OS fails to boot within the number of failures equal or greater than the value specified by Dell Auto OS Recovery Threshold, and local Service does not boot, or is not installed. Default: ON
	Dell Auto OS Recovery Threshold	Controls the automatic boot flow for SupportAssist System Resolution Console and for Dell operating system Recovery tool. Default: 2.

Table 8. System setup options—System Management menu
The following table describes the System Management menu options in the System setup program.
System Management
	Service Tag	Displays the Service Tag of the computer.
	Asset Tag	Creates a system Asset Tag that can be used by an IT administrator to uniquely identify a particular system. Once set in BIOS, the Asset Tag cannot be changed.

Table 9. System setup options—Pre-boot Behavior menu
The following table describes the Pre-boot Behavior menu options in the System setup program.
Pre-boot Behavior
	Adapter warnings
	Enable Adapter warnings	Enables or disables the computer to display adapter warning messages when adapters with too little power capacity are detected. Default: ON
	Warnings and Errors	Selects an action on encountering a warning or error during boot. Default: Prompt on Warnings and Errors. Stop, prompt, and wait for user input when warnings or errors are detected. NOTE: Errors deemed critical to the operation of the computer hardware will always halt the computer.

Table 10. System setup options—System Logs menu
The following table describes the System Logs menu options in the System setup program.
System Logs
	BIOS Event Log
	Clear Bios Event Log	Select keep or clear BIOS events. Default: Keep
	Thermal Event Log
	Clear Thermal Event Log	Select keep or clear Thermal events. Default: Keep
	Power Event Log
	Clear POWER Event Log	Select keep or clear Power events. Default: Keep