Dell OptiPlex 9020 Small Form Factor Owner's Manual

System Setup Options

NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not appear

Table 1. General
Option	Description
System Information	Displays the following information: System Information - Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Ownership Date, Manufacture Date, and the Express Service Code. Memory Information - Displays Memory Installed, Memory Available, Memory Speed, Memory Channels Mode, Memory Technology, DIMM 1 Size, DIMM 2 Size, DIMM 3 Size and DIMM 4 Size . PCI Information - Displays SLOT1, SLOT2, SLOT3,and SLOT4. Processor Information - Displays Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit Technology. Device Information - Displays SATA-0, SATA-1, SATA-2 , SATA-3 , LOM MAC Address, Audio Controller and Video Controller.
Boot Sequence	Allows you to specify the order in which the computer attempts to find an operating system. The options are: Diskette drive STXXXXXX / STXXXXXX USB Storage Device CD/DVD/CD-RW Drive Onboard NIC
Advanced Boot Options	Legacy UEFI
Advance Boot Options	Enable Legacy Option ROMs (enable by default)
Date/Time	Allows you to set the date and time. The changes to the system date and time takes effect immediately.

Table 2. System Configuration
Option	Description
Integrated NIC	Allows you to enable or disable the integrated network card. You can set the integrated NIC to: Enable UEFI Network Stack (disable by default) Disabled Enabled Enabled w/PXE default value Enabled w/Cloud Desktop NOTE: Depending on the computer and the devices installed, the items listed in this section may or may not appear.
Serial Port	Allows you to define the serial port settings. You can set the serial port to: Disabled COM1 COM2 COM3 COM4 NOTE: The operating system may allocate resources even though the setting is disabled.
SATA Operation	Allows you to configure the operating mode of the integrated hard drive controller. Disabled - The SATA controllers are hidden. ATA - SATA is configured for ATA mode. AHCI - SATA is configured for AHCI mode. RAID ON - SATA is configured to support RAID mode.
Drives	Allows you to enable or disable the various on-board drives: For Mini Tower SATA-0 SATA-1 SATA-2 SATA-3 For Small Form Factor SATA-0 SATA-1 SATA-2 For Ultra Small Form Factor M-SATA SATA 0 SATA 1
SMART Reporting	This field controls if the hard drive errors for the integrated drives are reported during system startup. This technology is part of the SMART (Self Monitoring Analysis and Reporting Technology) specification. Enable SMART Reporting - This option is disabled by default.
USB Configuration	This field configures the integrated USB controller. If Boot Support is enabled, the system is allowed to boot any type of USB mass storage devices (HDD, memory key, floppy). If USB port is enabled, device attached to this port is enabled and available for operation system. If USB port is disabled, the operation system cannot see any device attached to this port. USB configuration: For Mini-Tower, Small Form Factor the options are: Enable Boot Support Enable Front USB 2.0 Ports Enable USB 3.0 Ports Enable Rear—Left Dual USB 2.0 Ports Enable Rear —Right Dual USB 2.0 Ports (default value is enable) NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of these settings.
Audio	Allows you to enable or disable the integrated audio controller. Enable Audio (enable by default)
Miscellaneous Devices	Allows you to enable or disable various on-board devices. (For Mini Tower and Ultra Small Form Factor) Enable PCI Slot - This option is enabled by default.

Table 3. Security
Option	Description
Internal HDD_O Password	This field lets you set, change, or delete the administrator (admin) password (sometimes called the setup password). The admin password enables several security features. The drive does not have a password set by default. Enter the old password Enter the new password Confirm the new password
Strong Password	Enable strong password - This option is disabled by default.
Password Configuration	This field controls the minimum and maximum number of characters allowed for the admin and system passwords. Admin Password Min Admin Password Max System Password Min System Password Max
Password Bypass	Allows you to bypass the System Password and the internal HDD password prompts during a system restart. Disabled - Always prompt for the system and internal HDD password when they are set. This option is disabled by default. Reboot Bypass - Bypass the password prompts on restarts (warm boots). NOTE: The system will always prompt for the system and internal HDD passwords when powered on from the off state (a cold boot). Also, the system will always prompt for passwords on any module bay HDDs that may be present.
Password Change	Allows you to determine whether changes to the system and hard disk passwords are permitted when an administrator password is set. Allow Non-Admin Password Changes - This option is enabled by default.
TPM Security	This option lets you control whether the Trusted Platform Module (TPM) in the system is enabled and visible to the operating system. TPM Security - This option is disabled by default. TPM ACPI Support TPM PPI Deprovision Override Clear TPM PPI Provision Override NOTE: Activation, deactivation, and clear options are not affected if you load the setup program's default values. Changes to this option take effect immediately.
Computrace	This field lets you activate or disable the BIOS module interface of the optional Computrace Service from Absolute Software. Deactivate - This option is disabled by default. Disable Activate
Chassis Intrusion	Enable - This option is enabled by default. Disable On-Silent
CPU XD Support	Allows you to enable or disable the execute disable mode of the processor. Enable CPU XD Support - This option is enabled by default.
OROM Keyboard Access	Allows you to determine if you access the Option Read Only Memory (OROM) configuration screens via hotkeys during boot. These settings prevent access to the Intel RAID (CTRL+I) or Intel Management Engine BIOS Extension (CTRL+P/F12). Enable - User may enter OROM configuration screens via the hotkey. One-Time Enable - User can enter the OROM configuration screens via the hotkeys during the next boot. After the boot, the setting will revert to disabled. Disable - User can not enter the OROM configuration screens via the hotkey. This option is set to Enable by default.
Admin Setup Lockout	Allows you to enable or disable the option to enter setup when an admin password is set. Enable Admin Setup Lockout - This option is not set by default.
HDD Protection Support	Allows you to enable or disable the HDD Protection feature HDD Protection Support

Table 4. Secure Boot
Secure Boot Enable	Allows you to enable or disable Secure Boot feature Disable Enable NOTE: To enable secure boot, UEFI boot mode must be enabled and Enable Legacy Option ROMs must be disabled or turned off.
Expert key Management	Allows you to manipulate the security key databases only if the system is in Custom Mode. The Enable Custom Mode option is disabled by default. The options are: PK KEK db dbx If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx appear. The options are: Save to File- Saves the key to a user-selected file Replace from File- Replaces the current key with a key from a user-selected file Append from File- Adds a key to the current database from a user-selected file Delete- Deletes the selected key Reset All Keys- Resets to default setting Delete All Keys- Deletes all the keys NOTE: If you disable the Custom Mode, all the changes made will be erased and the keys will restore to default settings.

Table 5. Performance
Option	Description
Multi Core Support	Specifies whether the process will have one or all cores enabled. The performance of some applications will improve with the additional cores. All - Enabled by default 1 2
Intel SpeedStep	Allows you to enable or disable the Intel SpeedStep mode of the processor. This option is enabled by default.
C States Control	Allows you to enable or disable the additional processor sleep states. This option is enabled by default.
Limit CPUID Value	This field limits the maximum value the processor Standard CPUID Function will support Enable CPUID Limit NOTE: Some Operating system will not complete installation when the maximum CPUID Function is greater than 3
Intel TurboBoost	Allows you to enable or disable Intel TurboBoost mode of the processor. Disabled - Does not allow the TurboBoost driver to increase the performance state of the processor above the standard performance. Enabled - Allows the Intel TurboBoost driver to increase the performance of the CPU or graphics processor.
Hyper-Thread Control	Allows you to enable or disable the Hyper-Threading technology. This option is enabled by default.
Rapid Start Technology	Allows you to improve batter life by automatically putting the system into a low power status during after user specified amount of time. Intel Rapid Start feature NOTE: Rapid Start Technology will automatically be disabled due to configuration changes: Hard Disk Configuration or partition have been changed Memory capacity over 8GB installed. System or HDD password is enabled A Dell Encryption Accelerator is installed The Block Sleep setting is enabled

Table 6. Power Management
Option	Description
AC Recovery	Specifies how the computer will respond when AC power is applied after an AC power loss. You can set the AC Recovery to: Power Off (default) Power On Last Power State
Auto On Time	This option sets the time of the day when you would like the system to turn on automatically. Time is kept in standard 12-hour format (hour:minutes:seconds). The startup time can be changed by typing the values in the time and A.M./P.M. fields. Disabled - The system will not automatically power up. Every Day - The system will power up every day at the time you specified above . Weekdays - The system will power up Monday through Friday at the time you specified above. Select Days - The system will power up on days selected above at the time you specified above. NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power is set to disabled.
Deep Sleep Control	Allows you to define the controls when Deep Sleep is enabled. Disabled Enabled in S5 only Enabled in S4 and S5 This option is disabled by default.
Fan Control Override	Controls the speed of the system fan. This option is disabled by default. NOTE: When enabled, the fan runs at full speed.
USB Wake Support	This option allows you to enable USB devices to wake the computer from standby. Enable USB Wake Support - This option is disabled by default.
Wake on LAN	This option allows the computer to power up from the off state when triggered by a special LAN signal. Wake-up from the Standby state is unaffected by this setting and must be enabled in the operating system. This feature only works when the computer is connected to AC power supply. The options differ based on the form factor. Disabled - Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. LAN Only - Allows the system to be powered on by special LAN signals. WLAN Only - Allows the system to be powered on by special WLAN signals. (For Ultra Small Form Factor only) LAN or PXE Boot - Allows the system to be powered on by special LAN or PXE Bootsignals. (For Ultra Small Form Factor only) This option is Disabled by default.
Block Sleep	This option lets you block entering to sleep (S3 state) in operating system environment. Block Sleep (S3 state) - This option is disabled by default.
Intel Smart Connect Technology	The option is disabled by default. If option enables will periodically sense nearby wireless connection while the system is asleep. It will synchronize emails or social media application that were open when system entered the sleep state. Smart Connection

Table 7. POST Behavior
Option	Description
Numlock LED	Specifies if the NumLock function can be enabled when the system boots. This option is enabled by default.
Keyboard Errors	Specifies whether keyboard related errors are reported when it boots. This option is enabled by default.
MEBx Hotkeys	Specifies whether the MEBx Hotkey function should be enable when the system boots. Enable MEBx Hotkey — This option is enabled by default

Table 8. Virtualization Support
Option	Description
Virtualization	This option specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel Virtualization technology. Enable Intel Virtualization Technology - This option is enabled by default.
VT for Direct I/O	Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided by Intel® Virtualization technology for direct I/O. Enable Intel Virtualization Technology for Direct I/O - This option is enabled by default.
Trusted Execution	This option specifies whether a Measured Virtual Machine Monitor (MVMM) can utilize the additional hardware capabilities provided by Intel Trusted Execution technology. The TPM virtualization technology, and Virtualization technology for direct I/O must be enabled to use this feature. Trusted Execution - This option is disabled by default.

Table 9. Maintenance
Option	Description
Service Tag	Displays the service tag of your computer.
Asset Tag	Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default.
SERR Messages	Controls the SERR message mechanism. This option is not set by default. Some graphics cards require that the SERR message mechanism be disabled.

Table 10. Cloud Desktop
Option	Description
Server Lookup Method	Specifies how the ImageServer looks up the server address. Static IP DNS (enabled by default) NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer.
Server IP Address	Specifies the primary static IP address of the ImageServer with which the client software communicates. The default IP address is 255.255.255.255. NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer and when Lookup Method is set to Static IP.
Server Port	Specifies the primary IP port of the ImageServer, which is used by the client to communicate. The default IP port is 06910. NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer.
Client Address Method	Specifies how the client obtains the IP address. Static IP DHCP (enabled by default) NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer.
Client IP Address	Specifies the static IP address of the client. The default IP address is 255.255.255.255. NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer and when Client DHCP is set to Static IP.
Client SubnetMask	Specifies the subnet mask of the client. The default setting is 255.255.255.255. NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer and when Client DHCP is set to Static IP.
Client Gateway	Specifies the gateway IP address for the client. The default setting is 255.255.255.255. NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer and when Client DHCP is set to Static IP.
Advanced	Specifies for Advanced debugging Verbose Mode NOTE: This Option is only relevant when the integrated NIC control in the System Configuration group is set to enable with Cloud Desktop.

Table 11. System Logs
Option	Description
BIOS events	Displays the system event log and allows you to clear the log. Clear Log