Integrated Dell Remote Access Controller 9 RACADM CLI Guide

PDF

inlettemphistory

Table 1. Details of inlettemphistoryThe following table provides details about the inlettemphistory subcommand:
inlettemphistory
Description	Displays the average and the peak temperatures during the last hour, day, week, month, or year. Also Exports the inlet temperature history datafile. The file can be exported to a remote file share, local file system, or the management station. NOTE:For FM120x4 systems, this subcommand provides the historical data for system board temperature.
Synopsis	racadm inlettemphistory get racadm inlettemphistory export -f <Filename> -u <username> -p <password>\ -l <location> -t <export file type> racadm -r <idrac ip> -u <idrac username> -p <idrac password> inlettemphistory\ export -f <Filename> -u <username> -p <password> -l <location> -t <export file type> This command does not support setting the proxy parameters if the share location (-l) is HTTP/HTTPS. To perform the operation with HTTP or HTTPS through a proxy, the proxy parameters must be first configured using the lifecyclecontroller.lcattributes. Once these proxy parameters are configured, they become the part of default configuration; the proxy attributes should be cleared to end use of the HTTP/HTTPS proxy. The valid lifecyclecontroller.lcattributes HTTP/HTTPS proxy parameters are: UserProxyUserName UserProxyPassword UserProxyServer UserProxyPort UserProxyType To view the list of proxy attributes, use racadm get lifecycleController.lcAttributes.
Input	-f — Exports inlet temperature history filename. The maximum length of this parameter is 64 characters. NOTE:If a file with the specified filename exists, then the older file is replaced with the new history file. -u — User name of the remote share to export the file. Specify user name in a domain as domain or username. -p — Password for the remote share to where the file must be exported. -l — Network share location to where the inlet temperature history must be exported. The maximum length of this parameter is 256 characters. NOTE:The supported network locations are CIFS, NFS, HTTP, and HTTPS. -t — Specifies the exported file type. Valid values are xml and csv. These values are case-insensitive. NOTE:From RACADM firmware, only export to a remote share is supported. The behavior of remote share is not defined when the path specified (-l) contains special characters. NOTE:This command supports both IPV4 and IPV6 formats. IPV6 is applicable for CIFS, and NFS type remote shares.
Example	Export the log to a remote CIFS share. racadm inlettemphistory export -f Mylog.xml -u admin -p xxx -l //1.2.3.4/share -t xml Export the log to a remote HTTP share. racadm inlettemphistory export -f Mylog.xml -u httpuser -p httppwd\n -l http://test.com -t xml Export the log to a remote HTTPS share. racadm inlettemphistory export -f Mylog.xml -u httpsuser -p httpspwd\n -l https://test.com -t xml Export the log to a remote NFS share. racadm inlettemphistory export -f Mylog.csv -l 1.2.3.4:/home/user -t csv Export the log to a remote FTP share. racadm inlettemphistory export -f Mylog.csv -u ftpuser -p ftppwd -l ftp://test.com/share -t csv Export the log to a remote TFTP share. racadm inlettemphistory export -f Mylog.csv -l tftp://test.com/share -t csv Export the log to a local file system using Local RACADM. racadm inlettemphistory export -f Mylog.xml -t xml Export the log to the management station using Remote RACADM. racadm -r 1.2.3.4 -u user -p xxx inlettemphistory export -f Mylog.csv -t csv View the inlet temperature history. racadm inlettemphistory get Duration Above Warning Threshold as Percentage = 0.0% Duration Above Critical Threshold as Percentage = 0.0% Average Temperatures Last Hour = 23C ( 73.4F ) Last Day = 24C ( 75.2F ) Last Week = 24C ( 77.0F ) Last Month = 25C ( 77.0F ) Last Year = 23C ( 73.4F ) Peak Temperatures Last Hour = 23C ( 73.4F ) [At Wed, 21 May 2017 11:00:57] Last Day = 25C ( 77.0F ) [At Tue, 21 May 2017 15:37:23] Last Week = 27C ( 80.6F ) [At Fri, 20 May 2017 10:38:20] Last Month = 29C ( 84.2F ) [At Wed, 16 May 2017 15:34:13] Last Year = 29C ( 84.2F ) [At Wed, 16 May 2017 15:34:13] Configure the proxy parameter. racadm set lifecyclecontroller.lcattributes.UserProxyUsername admin1 Remove the proxy parameter. racadm set lifecyclecontroller.lcattributes.UserProxyUsername View the list of proxy attributes. racadm get lifecycleController.lcAttributes