PowerEdge Servers Error and Event Messages Reference Guide
BOOT—BOOT Control Event Messages
BOOT001
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The command was successful.
- Detailed Description
- The command was successful.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT002
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Resource allocation error.
- Detailed Description
- Unable to allocate required memory to perform the operation.
- Recommended Response Action
- Power cycle system and reapply firmware packages for Lifecycle Controller and iDRAC.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT003
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Method not supported.
- Detailed Description
- This operation is not supported on the current configuration.
- Recommended Response Action
- This operation is not supported on the current configuration, check documentation and try again.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT004
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Invalid number of Boot Source arguments
- Detailed Description
- An invalid number of source arguments was passed to the method.
- Recommended Response Action
- Check documentation and try again (details).
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT005
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Missing required parameter.
- Detailed Description
- One or more of the invoked methods required parameters are missing.
- Recommended Response Action
- Check documentation for the method in question and try again.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT006
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Invalid Boot Source InstanceID
- Detailed Description
- One or more of the Boot Source instance IDs does not contain valid data.
- Recommended Response Action
- Verify that all of the Boot Source instance IDs being entered are as they appear in the DCIM_BootSourceSetting enumeration.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT007
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Boot Source does not belong to specified Boot Configuration
- Detailed Description
- One or more of the Boot Source instance IDs does not belong to the affected Boot Configuration.
- Recommended Response Action
- ChangeBootOrderByInstanceID only accepts Boot Sources from the impacted Boot Configuration. Verify that all source arguments belong to the desired Boot Configuration.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT008
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Source argument contains more devices than are present on the system
- Detailed Description
- More source arguments were provided than are available for the impacted Boot Configuration.
- Recommended Response Action
- Verify that all of the Boot Source instance IDs being entered are as they appear in the DCIM_BootSourceSetting enumeration.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT009
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Boot Sources cannot be found for this Boot Configuration
- Detailed Description
- No Boot Sources could be found for the desired Boot Configuration.
- Recommended Response Action
- Verify that Boot Sources for the indicated Boot Configuration are displaying when enumerating DCIM_BootSourceSetting. Power cycle system and reapply firmware packages for Lifecycle Controller and iDRAC.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT010
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Could not locate vFlash partition index
- Detailed Description
- The provided vFlash partition index could not be found on the system.
- Recommended Response Action
- Verify that a vFlash partition with the desired index exists on the System.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT011
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Failed to set vFlash partition for one time boot
- Detailed Description
- The provided vFlash partition could not be set for one time boot.
- Recommended Response Action
- Power cycle system and reapply firmware packages for Lifecycle Controller and iDRAC.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT012
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Job started to attach and set vFlash SD card partition for OneTime boot.
- Detailed Description
- A job was created to configure a OneTime boot to the specified vFlash SD card partition. If this partition was not attached to the system, the job attaches it as well.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT013
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Cannot make changes to non-active boot list.
- Detailed Description
- The boot list is currently not active. Changes cannot be made to boot list that is not active.
- Recommended Response Action
- Alter boot mode to set the boot list active and retry the operation.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT014
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Virtual media not ready.
- Detailed Description
- The systems SD card has been removed or is in use.
- Recommended Response Action
- Verify that the SD card is inserted and that another operation is not in progress, and try again.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT015
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Set operation successful for the boot partition.
- Detailed Description
- The boot partition configuration request was successful. An unattached vFlash partition was configured for one-time boot using the ChangeBootOrderByInstanceID method. The method creates a job (to attach the vFlash partition and set the partition for one-time boot.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT016
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Input source argument value for the boot device is incorrect or not found among the boot devices on the system.
- Detailed Description
- The input source argument value referring to the boot device is incorrect or empty. The boot device identifier must match the InstanceID for the Boot Source Setting instance that represents the boot device.
- Recommended Response Action
- Use the correct source argument value for the boot device and retry the operation.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT017
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Source argument does not support enable or disable mode.
- Detailed Description
- The boot device(s) specified in the source argument used in the operation cannot be enabled or disabled. This behavior applies to BCV devices and one-time boot.
- Recommended Response Action
- Refer to the documentation on validity of operation for the boot device specified. For more information on the operation, see Lifecycle Controller-Remote Services documentation.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT018
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Specified Boot Control List is read-only
- Detailed Description
- The Boot Control List specified in the operation is read-only and cannot be modified.
- Recommended Response Action
- Refer to the documentation on validity of operation for the Boot Control List specified. For more information on the operation, see Lifecycle Controller-Remote Services documentation.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT019
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to run the ChangeBootOrderByInstanceID command because the BIOS Export operation is in progress.
- Detailed Description
- The ChangeBootOrderByInstanceID command cannot be run because the BIOS Export operation is in progress.
- Recommended Response Action
- Wait for the BIOS Export operation to complete and retry the operation.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT020
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to run the ChangeBootOrderByInstanceID command because the BIOS Import operation is in progress.
- Detailed Description
- The ChangeBootOrderByInstanceID command cannot be run because the BIOS Import operation is in progress.
- Recommended Response Action
- Wait for the BIOS Import operation to complete and retry the operation.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
BOOT8500
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to change the BIOS boot order for the Server arg1
- Arguments
- arg1 = slot number
- Detailed Description
- Unable to change the BIOS boot order for the server because of a broken communication between the CMC and iDRAC, or iDRAC is rebooting.
- Recommended Response Action
- Reset iDRAC or wait until iDRAC reboots, and retry the operation.
- Category
- Configuration (BOOT = BOOT Control)
- Severity
- Critical
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\