PowerEdge Servers Error and Event Messages Reference Guide

LC—Lifecycle Controller Event Messages

LC001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Command successful.
Detailed Description: The command completed successfully.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: General failure.
Detailed Description: A general failure occurred while executing the command.
Recommended Response Action: Verify network connectivity. If failure persists, reset the iDRAC to resolve the issue.
Category: Configuration (LC = Lifecycle Controller)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Failed to change the firmware update mode.
Detailed Description: An error occurred while trying to set the firmware update mode.
Recommended Response Action: Verify that the firmware version supports this mode. Also confirm that the command and parameters are correct. The parameter choices are: 1) Disable (default) 2) Allow version upgrade only 3) Match firmware of replaced part.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Provisioning Server information is not formatted correctly.
Detailed Description: The Provisioning Server parameter information is not formatted correctly.
Recommended Response Action: Verify the string format. Enter a valid IP address or hostname for the Provisioning Server such as: 1) hostname 2) hostname.domain.com 3) 1.1.1.1 4) hostname:8080 5) hostname.dell.com:8080 6) hostname1:80,hostname2:8080.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid firmware update mode.
Detailed Description: The value provided for the update mode parameter is invalid.
Recommended Response Action: Verify that the correct firmware update mode was entered. The choices are: 1) Disable (default) 2) Allow version upgrade only 3) Match firmware of replaced part.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid Auto-Discovery action.
Detailed Description: The Auto-Discovery action selected is invalid.
Recommended Response Action: Verify that the selected Auto-Discovery action is supported. The supported commands are documented in the Lifecycle Controller User Guide.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid Parameter.
Detailed Description: One of the parameters specified in the method is invalid.
Recommended Response Action: Verify that the parameters specified are correct. For a list of parameters for this method refer to the Lifecycle Controller User Guide.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unsupported method parameter value.
Detailed Description: The parameter value is not supported.
Recommended Response Action: Confirm that the parameters provided are correct. For a list of parameters for this method refer to the Lifecycle Controller User Guide.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Insufficient method parameters.
Detailed Description: There were insufficient parameters specified for this command.
Recommended Response Action: Confirm that the parameters provided are correct. For a list of parameters for this method refer to the Lifecycle Controller User Guide.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Certificate imported successfully.
Detailed Description: The communications encryption certificate was imported successfully.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC0100

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle Controller has entered Recovery mode.
Detailed Description: A persistent error has occurred while carrying out a Lifecycle Controller operation. This situation causes Lifecycle Controller to enter Recovery mode. Any remote jobs pending execution were cancelled.
Recommended Response Action: To verify or change Recovery mode, use F2 Setup, select iDRAC Configuration, and select Lifecycle Controller Settings. Updating Lifecycle Controller clears the Recovery mode.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC0101

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle Controller action was cancelled by a user.
Detailed Description: A user cancelled Lifecycle Controller actions. Any remote jobs pending execution were cancelled.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Certificate import operation failed.
Detailed Description: There was a general failure in the certificate import process.
Recommended Response Action: Do the following and retry the operation: 1) Redfish: Rerun the command or reset the iDRAC by invoking the iDRACReset method which is defined in the DelliDRACCardService class. 2) iDRAC GUI: Restart the iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Another process is using Lifecycle Controller.
Detailed Description: Lifecycle Controller is in use by another process. Wait for other process to complete before attempting to run another command.
Recommended Response Action: Try one of the following: 1) Rerun the command after about 2 minutes. 2) Make sure that Lifecycle Controller Unified Server Configurator or an Update Package is not currently running on the server 3) Reset iDRAC and rerun the command.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Operation cannot be completed because there are no pending configuration.
Detailed Description: No changes are available between the previous configuration and the current configuration. At least one attribute should be changed to create a configuration job.
Recommended Response Action: Change the configuration of one or more attributes before creating a configuration job.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Maximum comment length is 255 characters.
Detailed Description: Maximum comment length is 255 characters.
Recommended Response Action: Limit the number of characters in the comment to 255 characters.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid Part Configuration Update
Detailed Description: Invalid current attribute value.
Recommended Response Action: Check for correct parameter values: 1) Disabled 2) Apply always 3) Apply only if firmware match.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Missing required parameter, arg1.

Arguments

arg1 = parameter

Detailed Description

A required method argument was missing.

Recommended Response Action

Include all the parameters required for the command. Check Lifecycle Controller Profile documentation and try again.

Category

Configuration (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC017

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid value for the parameter, arg1.

Arguments

arg1 = parameter

Detailed Description

A parameter value provided when the method was invoked is not valid.

Recommended Response Action

Verify that parameter values provided to the method are typed as they appear in the enumeration and that the parameter data type matches the Lifecycle Controller Profile documentation.

Category

Configuration (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC018

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The server certificate is successfully modified. To make the new certificate effective, reset iDRAC.
Detailed Description: The server certificate is successfully modified. To make the new certificate effective, reset iDRAC.
Recommended Response Action: To reset iDRAC, do one of the following:1) On the iDRAC User Interface: Click Dashboard > Reboot iDRAC.2) On the RACADM Interface: Run the racadm racreset command.3) On the Redfish Interface: Use the iDRACReset action defined in the DelliDRACCardService schema.For more information about updating the iDRAC certificate, refer to the iDRAC Users Guide available on the support site.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC019

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Base64 decode of PKCS12 content was not successful.
Detailed Description: The PKCS12 string could not be decoded from the Base64 encoding into a PKCS12 binary file.
Recommended Response Action: Validate that the contents of the PKCS12 parameter is base64 encoded. OpenSSL can be used to validate the encoding.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC020

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: PKCS12 decrypt of the certificate could not complete.
Detailed Description: The contents of the PKCS12 parameter was not valid because: 1) not a valid PKCS12 file 2) not a valid pfx file 3) did not contain a certificate that matched the private key in the file.
Recommended Response Action: Validate that the PKCS12 content was Base64 encoded. OpenSSL can be used to create or validate a PKCS12 encoding.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC021

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: PKCS12 decrypt of private key could not complete.
Detailed Description: The contents of the PKCS12 parameter was not valid because: 1) not a valid PKCS12 file 2) not a valid pfx file 3) did not contain a valid key.
Recommended Response Action: Validate that the PKCS12 file was Base64 encoded. OpenSSL can be used to create or validate a PKCS12 file.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC022

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle Controller Log Export was successful.
Detailed Description: The Lifecycle Controller Log was successfully exported to the destination specified.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC023

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Cannot access network share.
Detailed Description: Credentials or network share identity information provided did not result in a network connection being established.
Recommended Response Action: Check network share access credentials (IP address, user name, password, share type, and so on). Refer to Lifecycle Controller Profile documentation for more details.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC024

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve Lifecycle Controller Log records.
Detailed Description: Unable to retrieve Lifecycle Controller Log records because of an issue internal to the firmware.
Recommended Response Action: Do one of the following: 1) Try the operation again 2) AC power cycle the system 3) apply the latest firmware update packages for Lifecycle Controller and iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC025

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Insufficient space on network share.
Detailed Description: Insufficient space on network share.
Recommended Response Action: Make more space available on the network share and try the operation again.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC026

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle Controller Log Export method is not supported.
Detailed Description: This method is not supported in this version of the iDRAC firmware.
Recommended Response Action: Update the iDRAC firmware to a version that supports the log export.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC027

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Hardware Inventory file export was successful.
Detailed Description: The Hardware Inventory XML file export operation was successful.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC028

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve Hardware Inventory information.
Detailed Description: Hardware Inventory information is not retrievable due to an internal error.
Recommended Response Action: Try one of the following: 1) Try the operation again 2) AC power cycle system 3) apply the latest firmware update packages for Lifecycle Controller and iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC029

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid file path specified.
Detailed Description: An invalid File Path was specified in the export operation.
Recommended Response Action: Correct the specified file path and try again.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC030

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The file path is to a read-only file system.
Detailed Description: The file path specified for the operation is a read-only file system.
Recommended Response Action: Enable write access to the file path and try again.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC031

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Internal error occurred while exporting inventory.
Detailed Description: An internal error occurred while exporting the Hardware Inventory XML file.
Recommended Response Action: Reset iDRAC and retry the command.
Category: Configuration (LC = Lifecycle Controller)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC032

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Hardware Inventory Export method not supported.
Detailed Description: This method is not supported in the current version of iDRAC firmware.
Recommended Response Action: Update the iDRAC firmware to a version that supports this method.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC033

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: As-Shipped Hardware Inventory export was successful.
Detailed Description: The Hardware Inventory XML file representing the system configuration as shipped from the factory was successful.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC034

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve As-Shipped Hardware Inventory from the system.
Detailed Description: The As-Shipped from the factory Hardware Inventory information is not present on the system.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC035

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: As-Shipped Hardware Inventory Export method is not supported.
Detailed Description: This method is not supported in this version of Firmware.
Recommended Response Action: Update the iDRAC firmware to a version that supports this method.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC036

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle Controller is not enabled.
Detailed Description: The Lifecycle Controller has been disabled through the iDRAC configuration utility accessed by pressing CTRL+E or F2 on boot up or through a remote command.
Recommended Response Action: For 11G systems: Use the iDRAC configuration utility to enable the System Services by pressing on the CTRL+E option on boot up at the targeted system. For 12G and above generations : Use F2 Setup, select iDRAC Configuration, and select Lifecycle Controller Settings, to enable the Lifecycle Controller on boot up of the targeted system.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC037

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An instance of Lifecycle Controller Log Export is already running.
Detailed Description: Lifecycle Controller is locked by another instance of Lifecycle Controller Log Export operation. Wait for that operation to complete before attempting to run another command.
Recommended Response Action: Do one of the following: 1) Wait approximately 2 minutes and retry the operation. 2) Reset iDRAC and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC038

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An instance of Hardware Inventory export is already in progress.
Detailed Description: Lifecycle Controller is locked by another instance of the Hardware Inventory export process. Allow the process to complete before attempting another export operation.
Recommended Response Action: Do one of the following: 1) Rerun the command after about 2 minutes 2) Reset the iDRAC and rerun the command.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC039

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An instance of As-Shipped Inventory export is already in progress.
Detailed Description: Lifecycle Controller is locked by another instance of the As-Shipped Inventory export process. Allow the process to complete before attempting another export operation.
Recommended Response Action: Do one of the following: 1) Rerun the command after about 2 minutes 2) Reset iDRAC and rerun the command.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC040

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Memory resource allocation failure.
Detailed Description: Unable to allocate required memory to perform the operation.
Recommended Response Action: Power cycle system and retry the operation. If the problem persists, reapply firmware packages for Lifecycle Controller and iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC041

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Console name configure failed
Detailed Description: The length of the Console name exceeds the maximum length allowed or the file operation error encountered.
Recommended Response Action: Change the name of a console to a name less than 32 characters.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC042

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Configure Console name in FlexAddress mode
Detailed Description: Configure Console name while Virtual Address Management is in FlexAddress mode.
Recommended Response Action: Configure the Virtual Address Management to Console mode, and then configure the name of a console.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC043

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Work note contains non-printable or reserved characters.
Detailed Description: Work notes cannot include non-printable or reserved characters, such as &, <, >, /.
Recommended Response Action: Do not use non-printable characters or reserved characters such as &, , and /.
Category: Updates (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC044

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An instance of Lifecycle Controller system configuration wipe is already running.
Detailed Description: The Lifecycle Controller system configuration wipe operation is currently running. The operation deletes user information from system hardware and resets BIOS, iDRAC and Lifecycle Controller to default settings. The current operation and system restart must complete before the operation can be attempted again.
Recommended Response Action: Wait for the Lifecycle Controller system configuration wipe operation that is currently running to complete before requesting another operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC045

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An instance of CreateConfigJob is already running.
Detailed Description: The CreateConfigJob operation is currently running. The current operation and system restart must complete before the operation can be attempted again.
Recommended Response Action: Wait for the CreateConfigJob operation that is currently running to complete before requesting another operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC046

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An instance of DownloadServerPublicKey is already running.
Detailed Description: The DownloadServerPublicKey operation is in progress. The operation may take a few minutes to complete before the operation can be attempted again.
Recommended Response Action: Wait a few minutes before retrying retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC047

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An instance of DownloadClientCerts is already running.
Detailed Description: The DownloadClientCerts operation is in progress. The operation may take a few minutes to compete before the operation can be attempted again.
Recommended Response Action: Wait a few minutes before retrying retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC048

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid input value for IPChangeNotifyPS.
Detailed Description: The value provided to set the attribute identified in the message is invalid.
Recommended Response Action: For more information on the valid values, see Lifecycle Controller-Remote Services documentation. Retry the operation with a valid value for the IPChangeNotifyPS attribute.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC049

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid value for VirtualAddressManagement.
Detailed Description: The value provided to set the attribute identified in the message is invalid.
Recommended Response Action: For more information on the valid values, see Lifecycle Controller-Remote Services documentation. Retry the operation with a valid value for the VirtualAddressManagement attribute.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC050

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid value for SystemServicesState.
Detailed Description: The value provided to set the attribute identified in the message is invalid.
Recommended Response Action: For more information on the valid values, see Lifecycle Controller-Remote Services documentation. Retry the operation with a valid value for the SystemServicesState attribute.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC051

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Cannot create multiple Server Profile Export jobs.
Detailed Description: There can only be one Server Profile Export job at a time.
Recommended Response Action: Wait for the existing Server Profile Export job to run and complete or cancel it, before retrying the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC052

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Cannot create multiple Server Profile Import jobs.
Detailed Description: There can only be one Server Profile Import job at a time.
Recommended Response Action: Wait for the existing Server Profile Import job to run and complete or cancel it, before retrying the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC053

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle Controller Remote Services is currently unavailable.
Detailed Description: Lifecycle Controller Remote Service is either not ready or currently reloading server information.
Recommended Response Action: Retry the operation. If the issue persists, refer to Lifecycle Controller-Remote Services documentation for more information.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC054

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to write to the network share.
Detailed Description: The network share may be read-only or it may not have sufficient space for the export operation.
Recommended Response Action: Verify the network share is not read-only and has sufficient space for exporting, then retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC055

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation did not complete successfully because of an invalid attribute array.
Detailed Description: The operation did not complete successfully because the number of AttributeName input parameters provided to the method exceeded the number of attributes available in iDRAC.
Recommended Response Action: Retry the operation with an input parameter array that matches the available attributes in iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC056

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: AttributeName and AttributeValue count mismatch.
Detailed Description: The name value pairs in the input parameter arrays do not match in the input.
Recommended Response Action: Retry the operation with a valid (AttributeName, AttributeValue) pair.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC057

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid AttributeName parameter value.
Detailed Description: The attribute name provided is not valid for the current method.
Recommended Response Action: Retry the operation with a valid AttributeName parameter value.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC058

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid AttributeValue parameter value for corresponding AttributeName value, arg1.

Arguments

arg1 = AttributeName

Detailed Description

The attribute value specified in the AttributeValue array is not valid for the corresponding specified attribute.

Recommended Response Action

Retry the operation with a valid attribute value for the corresponding specified attribute.

Category

Configuration (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC059

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Cannot set read only attribute specified in AttributeName arg1.

Arguments

arg1 = parameter

Detailed Description

The attribute specified is read only and the value cannot be changed.

Recommended Response Action

No response action is required.

Category

Configuration (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC060

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle controller is currently not ready to take provisioning requests
Detailed Description: Lifecycle controller is currently performing tasks and another task cannot be scheduled until the previous task finishes.
Recommended Response Action: Wait until Lifecycle controller finishes performing current tasks and host system to finish POST.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC061

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Lifecycle controller is ready to take provisioning requests
Detailed Description: Jobs, invoke methods, enumerates can now be performed on Lifecycle controller. Lifecycle controller is ready to take provisioning requests.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC062

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Export or Import server profile operation is already running.
Detailed Description: Export or Import server profile operation is already running. The operation may take a few minutes to compete.
Recommended Response Action: To retry the operation, wait for a few minutes.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC063

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Cannot create new jobs until the existing running jobs are completed or deleted.
Detailed Description: All jobs must be completed before creating a new job.
Recommended Response Action: Retry after all the existing jobs are completed or deleted.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC064

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The value exceeds the maximum length of arg1 characters for arg2.

Arguments

arg1 = max parameter length
arg2 = parameter name

Detailed Description

The maximum number of characters allowed for the parameter is displayed.

Recommended Response Action

Reduce the number of characters to the maximum length allowed for this parameter.

Category

Configuration (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC065

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The iDRAC static IP address information is not fully configured. The missing attribute InstanceID is arg1.

Arguments

arg1 = attribute key

Detailed Description

The static IPv4 information for the iDRAC represented by the related iDRACCard Attributes must be configured correctly.

Recommended Response Action

Configure the iDRAC static IP address information by setting the related iDRACCard Attributes. The related attributes that must be configured are the following:: 1) In the IPv4 group: Address, NetMask, Gateway, DNS1 2) In the NIC Static group: DNSDomainName.

Category

Configuration (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC066

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Export Certificate operation is currently running.
Detailed Description: The Export Certificate operation is already running and may take a few minutes to complete.
Recommended Response Action: Wait until the current operation is complete and then retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC067

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully exported SSL Certificate.
Detailed Description: The Export Certification operation successfully exported the SSL Certificate.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC068

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the import or export operation because there are pending attribute changes or a configuration job is in progress.
Detailed Description: The import or export system configuration operation cannot be performed because there are pending attribute changes or a configuration job is in progress.
Recommended Response Action: Apply or cancel any pending attribute changes. Changes can be applied by creating a targeted configuration job, or the changes can be cancelled by invoking the DeletePendingConfiguration method. If a configuration job is in progress, wait until it is completed before retrying the import or export system configuration operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC069

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Certificate does not exist.
Detailed Description: The certificate does not exist for export or delete operation.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC070

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to find the configuration XML import file.
Detailed Description: The configuration XML file used for the import operation does not exist on the specified network share.
Recommended Response Action: Make sure the input configuration XML file for the operation exists on the network share.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC071

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Lifecycle Controller version does not support the export or import of the Server Configuration XML file.
Detailed Description: Unable to export or import server configuration XML because the Lifecycle Controller version on the target does not support this feature.
Recommended Response Action: Update the Lifecycle Controller version on the target system to a version that supports the export and import server configuration XML feature, and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC072

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: An SSL Certificate is successfully generated.
Detailed Description: An SSL Certificate is successfully generated in response to the requested operation.
Recommended Response Action: Download the SSL Certificate and get it signed by an authority.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC073

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate an SSL Certificate because of internal firmware issues.
Detailed Description: An SSL Certificate cannot be generated because of internal firmware issues.
Recommended Response Action: Ensure the security attributes are correct and retry the operation. If the issue persists, reboot iDRAC using one of the following methods and then retry the operation:1) On the Redfish Interface: Invoking the iDRACReset action in DelliDRACCardService.2) On the iDRAC User Interface: Click Dashboard > Reboot iDRAC.For information about validating these attributes, see the iDRAC Users Guide and Redfish API Guide available on the support site.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC074

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Certificate export operation did not complete successfully.
Detailed Description: The Certificate export operation did not complete successfully.
Recommended Response Action: Retry the operation. If the issue persists, restart the iDRAC and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC075

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Custom Signed Certificate (CSC) is deleted successfully. Reset iDRAC to complete the delete action of the certificate.
Detailed Description: Deleting the custom signed certificate should regenerate a new unique certificate . Reset iDRAC to apply new certificate. Until iDRAC is reset old certificate will be active.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC076

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the Custom Signed Certificate (CSC) certificate delete operation.
Detailed Description: Unable to perform the Custom Signed Certificate (CSC) certificate delete operation. This may be due to IPMI communications issues.
Recommended Response Action: Retry the operation. If the issue persists, restart the iDRAC and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC077

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Certificate imported successfully. Reset iDRAC to apply new certificate. Until iDRAC is reset old certificate will be active
Detailed Description: The new certificate will not be in-use until iDRAC has been restarted.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC078

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Export Message Registry operation was successfully completed.
Detailed Description: The Message Registry was successfully exported to the specified destination file folder.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC079

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the export operation because Lifecycle Controller is currently running an instance of Export Message Registry operation.
Detailed Description: The export operation cannot be started because Lifecycle Controller is currently running an instance of Export Message Registry operation.
Recommended Response Action: Wait for the current export process to complete, and then retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC080

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Export Server Screen Shot operation successfully exported the server screen shot file.
Detailed Description: The Export Server Screen Shot operation successfully exported the server screen shot file.
Recommended Response Action: Download the encoded Base64 format server screen shot file, decode the Base64 file and then save it as a *.png file.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC081

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the Server Screen Shot export operation because of internal issues.
Detailed Description: The Server Screen Shot export operation cannot be completed because of internal issues.
Recommended Response Action: Retry the operation. If the issue persists restart iDRAC by doing one of the following, and then retry the operation:1) On the Redfish Interface, invoke the iDRACReset action in DelliDRACCardService. 2) At the RACADM CLI, run the racadm racreset command. 3) On the iDRAC User Interface, click Dashboard > Reboot iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC082

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the requested operation because the Collect System Inventory On Restart (CSIOR) attribute setting is disabled on the system.
Detailed Description: Unable to complete the requested operation because the Collect System Inventory On Restart (CSIOR) attribute setting is disabled on the system.
Recommended Response Action: Enable the Collect System Inventory On Restart (CSIOR) attribute setting and then retry the operation. To enable the CSIOR setting using the RACADM command line utility, type "racadm set lifecyclecontroller.LCAttributes.CollectSystemInventoryOnRestart Enabled".
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC083

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Redfish Event service cannot deliver notifications to arg1 because of network communication issues.

Arguments

arg1 = IP address

Detailed Description

The Redfish Event service cannot deliver notifications to the IP Address identified in the message because of network communication issues.

Recommended Response Action

Make sure that the server is connected to the network and retry the operation. If the issue persists, delete the subscription and then subscribe by using an IP that is connected to the network.

Category

Audit (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC084

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the video log because there are no files in the source folder that can be compressed and exported.
Detailed Description: The video log cannot be exported because there are no files in the source folder that can be compressed and exported.
Recommended Response Action: For boot capture, make sure at least one boot video log captured to iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC085

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Export Video Log operation is successfully completed and the files are exported to iDRAC Local folder.
Detailed Description: The Export Video Log operation is successfully completed and the files are exported to iDRAC Local folder.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC086

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the Export Video Log operation because of internal issues.
Detailed Description: The video log file cannot be exported because of internal issues.
Recommended Response Action: Retry the operation. If the issue persists restart iDRAC by doing one of the following, and then retry the operation:1) On the Redfish Interface, invoke the iDRACReset action in DelliDRACCardService. 2) At the RACADM CLI, run the racadm racreset command. 3) On the iDRAC User Interface, click Dashboard > Reboot iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC087

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the configuration operation because System Lockdown mode is enabled.
Detailed Description: The configuration operation cannot be started because the System Lockdown mode is enabled.
Recommended Response Action: Make sure that the Lockdown.1#SystemLockdown attribute is set to Disabled and then retry the operation. For information about the Lockdown mode, see the relevant iDRAC Users Guide available on the support site.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC088

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the server screen shot because there is no file in source folder.
Detailed Description: Unable to export the server screen shot because there is no file in source folder.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC089

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set the job to run on monthly or quarterly recurrence basis because necessary parameters are not entered in the command.
Detailed Description: The job cannot be set to run on monthly or quarterly recurrence basis because required parameters are not entered in the command.
Recommended Response Action: For setting monthly or quarterly recurrence, enter either the DayofMonth parameter, or the WeekofMonth and DayofWeek parameters. For information about correct syntax and parameters, see the Profile Documents on the TechCenter website.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC090

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to register iDRAC to SupportAssist because the length of parameter arg1 entered is less than the stipulated length arg2.

Arguments

arg1 = parameter name
arg2 = min. parameter length

Detailed Description

The iDRAC cannot be registered to SupportAssist because the length of parameter entered is less than the stipulated length as identified in the message.

Recommended Response Action

Make sure that the parameter length is more than or equal to minimum allowed length and retry the operation. For information about specified parameter length, see the SupportAssist documentation on DellTechCenter.

Category

Configuration (LC = Lifecycle Controller)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC091

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate the SSL Certificate because a certificate generation process is currently in progress.
Detailed Description: The SSL Certificate cannot be generated because a certificate generation process is currently in progress.
Recommended Response Action: Wait for the current Certificate generation process to complete and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC092

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to delete the Client Trust Certificate because of issues in the Intelligent Platform Management Interface (IPMI).
Detailed Description: The Client Trust Certificate cannot be deleted because of issues in the Intelligent Platform Management Interface (IPMI).
Recommended Response Action: Retry the operation. If the issue persists, restart the iDRAC and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC093

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Client Trust Certificate is successfully deleted.
Detailed Description: The Client Trust Certificate is successfully deleted.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC094

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Export SVG file operation is successfully completed and the files are exported to iDRAC Local folder.
Detailed Description: The Export SVG (Scalable Vector Graphics) file operation is successfully completed and the files are exported to iDRAC Local folder.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC095

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the SVG file because of internal issues.
Detailed Description: The SVG file cannot be exported because of internal issues.
Recommended Response Action: Retry the operation. If the issue persists, do one of the following: 1) On the Redfish Interface, invoke the iDRACReset action in DelliDRACCardService. 2) At the RACADM CLI, run the racadm racreset command. 3) On the iDRAC User Interface, click Dashboard > Reboot iDRAC.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC096

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SSL Certificate is successfully imported.
Detailed Description: The SSL Certificate is successfully imported.
Recommended Response Action: No response action is required.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC097

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the Diagnostics report because the proxy port number entered is invalid.
Detailed Description: The Diagnostics report cannot be exported because the proxy port number entered is invalid.
Recommended Response Action: Enter a valid proxy port number and retry the operation. The valid range is 0-65535. For more information, see the iDRAC Users Guide available on the support site.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC098

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the server screen shot because the iDRAC is busy in capturing the current screen shot.
Detailed Description: The server screen shot cannot be exported because the iDRAC is busy in capturing the current screen shot.
Recommended Response Action: Wait for the current process to complete and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC099

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the server screen shot because the video signal is not detected.
Detailed Description: The server screen shot cannot be exported because the video signal is not detected.
Recommended Response Action: Turn on the server if turned off, and then retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC100

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the server screen shot because of File Write Error.
Detailed Description: The server screen shot cannot be exported because of File Write Error.
Recommended Response Action: Wait for some time and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC101

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the server screen shot because the operation timed out before capturing the screen shot.
Detailed Description: The server screen shot cannot be exported because the operation timed out before capturing the screen shot.
Recommended Response Action: Wait for some time and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC102

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the server screen shot because iDRAC could not get the necessary screen data.
Detailed Description: The server screen shot cannot be exported because iDRAC could not get the necessary screen data.
Recommended Response Action: Wait for some time and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC103

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the server screen shot because iDRAC is unable to process the screen data.
Detailed Description: The server screen shot cannot be exported because iDRAC is unable to process the screen data.
Recommended Response Action: Wait for the current process to complete and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC104

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create the new job because a backup and restore job is already running.
Detailed Description: The new job cannot be created because a backup and restore job is already running. Any pending value will be deleted.
Recommended Response Action: Wait for the current backup and restore job to complete, and then retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC105

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Certificate Signing Request (CSR) certificate of arg1 is successfully created.

Arguments

arg1 = certificate Name

Detailed Description

The Certificate Signing Request (CSR) certificate is successfully created as identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (LC = Lifecycle Controller)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC106

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate the Certificate Signing Request (CSR) certificate because of internal firmware issues.
Detailed Description: The Certificate Signing Request (CSR) certificate cannot be generated because of internal firmware issues.
Recommended Response Action: Do the following and retry the operation. 1) REST API: Make sure that the SEKMCert group attributes are valid and retry the operation. 2) RACADM CLI: To view the SEKMCert attributes, run the following command at the Command Line Interface (CLI):racadm get idrac.sekmcert. 3) iDRACGUI:For information about valid and correct attributes, see the iDRAC Users Guide available on the support site.
Category: Configuration (LC = Lifecycle Controller)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC107

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 certificate is successfully imported.

Arguments

arg1 = Certificate Type

Detailed Description

The certificate identified in the message is successfully imported.

Recommended Response Action

No response action is required.

Category

Configuration (LC = Lifecycle Controller)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC108

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 certificate is successfully exported.

Arguments

arg1 = Certificate Type

Detailed Description

The certificate identified in the message is successfully exported.

Recommended Response Action

No response action is required.

Category

Configuration (LC = Lifecycle Controller)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC109

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 certificate is successfully deleted.

Arguments

arg1 = Certificate Type

Detailed Description

The certificate identified in the message is successfully deleted.

Recommended Response Action

No response action is required.

Category

Configuration (LC = Lifecycle Controller)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

LC110

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate the CSR Certificate because a certificate generation process is currently in progress.
Detailed Description: The CSR Certificate cannot be generated because a certificate generation process is currently in progress.
Recommended Response Action: Wait for the current Certificate generation process to complete and retry the operation.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC111

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to delete the certificate because the certificate does not exist.
Detailed Description: The certificate cannot be deleted because the certificate does not exist.
Recommended Response Action: Make sure that the certificate entered exists in the iDRAC, and then retry the operation. To check by using the RACADM CLI, run "racadm sslcertview -t . On the iDRAC9 and later version of GUI, click Settings > Services. If the certificates exist, data is populated in the SEKM Configuration and/or KMS CA certificate sections.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC112

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to validate the SEKM SSL Certificate because certificate is invalid.
Detailed Description: The SEKM SSL Certificate cannot be validated because certificate is invalid. The SEKM SSL Certificate is invalid because of one or more of the following reasons: 1) The certificate is corrupted, expired, or does not have signing privileges. 2) The SEKM SSL private key does not match with the SEKM SSL Certificated that is uploaded.
Recommended Response Action: Make sure the SEKM SSL Certificate and private key are valid, and then retry the operation. To validate the certificate, use the OpenSSL tools.
Category: Configuration (LC = Lifecycle Controller)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

LC113

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 subscription is successfully created but the licensed events are not included because the required license version is unavailable.

Arguments

arg1 = which

Detailed Description

The subscription is successfully created but the licensed events are not included because the required license version is unavailable.

Recommended Response Action

Install the recommended license version to view licensed events. For information about licensed events, see the Lifecycle Controller Users Guide available on the support site.

Category

Configuration (LC = Lifecycle Controller)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable