PowerEdge Servers Error and Event Messages Reference Guide
NIC—NIC Configuration Event Messages
NIC001
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The command was successful.
- Detailed Description
- The command was successful.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC002
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Resource allocation failure
- Detailed Description
- Unable to allocate required memory to perform the operation.
- Recommended Response Action
- Power cycle system and reapply firmware packages for Lifecycle Controller and iDRAC.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Critical
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC003
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Missing required parameter
- Detailed Description
- An invalid number of arguments was passed to the method.
- Recommended Response Action
- Enter all the required command parameters. Check documentation and try again.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC004
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Invalid parameter value for arg1
- Arguments
- arg1 = attribute name
- Detailed Description
- The value for the specified parameter is invalid.
- Recommended Response Action
- Verify that parameter values passed to the method are entered as they appear in the enumeration and parameter data type matches the documentation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC005
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Mismatch in AttributeName and AttributeValue count
- Detailed Description
- The number of AttributeName and AttributeValue parameters do not match.
- Recommended Response Action
- Pass the same number of parameters for AttributeName and AttributeValue. Refer to documentation for method input parameter details.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC006
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- A configuration job already exists, Cannot set attribute on specified target until existing job is completed or is cancelled
- Detailed Description
- A configuration job already exists for the specified target. No further configuration operation is allowed until the existing job completes or the job is cancelled.
- Recommended Response Action
- Do one of the following: 1) Wait for the existing configuration job to complete and retry the operation, 2) To continue with a configuration change, cancel the existing job and retry the operation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC007
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- A configuration job already exists, Cannot create another configuration job on specified target until existing job is completed or is cancelled
- Detailed Description
- A configuration job already exists for the specified target. No further configuration operation is allowed until the existing job completes or the job is cancelled.
- Recommended Response Action
- Do one of the following: 1) Wait for the existing configuration job to complete and retry the operation, 2) To continue with a configuration change, cancel the existing job and retry the operation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC008
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- No pending data present to create a Configuration job
- Detailed Description
- No changes are available between the previous configuration and the current configuration. To create a Configuration job, at least one attribute should be changed.
- Recommended Response Action
- Change the configuration of one or more attributes and then create a configuration job.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC009
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Lifecycle Controller is currently in use.
- Detailed Description
- Lifecycle Controller cannot gain access to internal storage because it is use by another application or operation.
- Recommended Response Action
- Wait for the current Lifecycle Controller operation to complete. Verify that the system is 1) Not currently in Lifecycle Controller Unified Server Configurator utility 2) Not waiting for user intervention at F1/F2 POST error 3) Not in any of the device or controller Option ROMs and retry the operation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC010
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Lifecycle Controller is not enabled, cannot create Configuration job.
- Detailed Description
- For 11G systems: System Services must be enabled to perform the requested operation. System Services has been disabled through the iDRAC configuration utility accessed by pressing CTRL+E on boot up or through a remote operation. For 12G and above generations: Lifecycle Controller must be enabled to perform the requested operation. Lifecycle Controller has been disabled by pressing F2 Setup, selecting iDRAC Configuration, and selecting Lifecycle Controller Settings on boot up or through a remote operation.
- Recommended Response Action
- For 11G systems: Use the iDRAC configuration utility to enable the System Services by pressing on the CTRL+E option on boot up at the targeted system. For 12G and above generations: Use F2 Setup, select iDRAC Configuration, and select Lifecycle Controller Settings, to enable the Lifecycle Controller on boot up of the targeted system.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC011
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Configuration job already created, pending data cannot be deleted
- Detailed Description
- Configuration job already created on the specified target. No further command is allowed until the existing job is completed.
- Recommended Response Action
- Cancel the configuration job or wait for the job to complete. Refer to documentation on job cancellation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC012
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- No pending data to delete.
- Detailed Description
- No changes to BIOS attribute data are available between the previous configuration and the current configuration.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC013
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Invalid AttributeName: arg1
- Arguments
- arg1 = attribute name
- Detailed Description
- An unknown AttributeName was entered for the operation.
- Recommended Response Action
- Enter the correct AttributeName available in the system. Refer to the enumeration response for desired attribute.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC014
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Invalid AttributeValue for AttributeName arg1
- Arguments
- arg1 = attribute name
- Detailed Description
- AttributeValue may be invalid because of the following causes: 1) Length of new AttributeValue is not within minLength and maxLength 2) Value of new AttributeValue is not within LowerBound and UpperBound 3) Value of new AttributeValue is not one of the possible values.
- Recommended Response Action
- Refer to the documentation on valid attribute values.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC015
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- AttributeValue cannot be changed to read only AttributeName arg1.
- Arguments
- arg1 = attribute name
- Detailed Description
- A set attribute operation was attempted on a read only attribute.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC016
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- AttributeValue cannot be changed for disabled AttributeName arg1.
- Arguments
- arg1 = attribute name
- Detailed Description
- A set attribute operation was attempted on a disabled attribute.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC017
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to delete vFlash pending one-time boot configuration
- Detailed Description
- Unable to delete vFlash pending one-time boot configuration.
- Recommended Response Action
- Remove AC power from system and after restoring AC power, retry the operation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Critical
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC018
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Invalid BIOS password.
- Detailed Description
- The input BIOS password used in the operation is invalid.
- Recommended Response Action
- Use a valid BIOS password and retry.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC021
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Cannot authenticate specified BIOS password.
- Detailed Description
- The old BIOS password used to change the password is incorrect.
- Recommended Response Action
- Enter the correct old password for the BIOS and retry the operation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC022
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to set the BIOS password because of a jumper setting on the motherboard.
- Detailed Description
- The current BIOS password jumper setting prevents the BIOS password from being changed.
- Recommended Response Action
- Change the jumper setting to enable setting the BIOS password.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC023
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Cannot perform the operation due to an unknown error in iDRAC.
- Detailed Description
- The operation did not complete successfully because of an unknown error in iDRAC.
- Recommended Response Action
- Retry the action. If the issue persists, reset the iDRAC.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC024
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The set operation did not complete successfully as the attribute is read-only.
- Detailed Description
- The attribute specified in the operation is currently read only and the value cannot be modified.
- Recommended Response Action
- For more information on the attribute, see Lifecycle Controller-Remote Services documentation.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC025
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to start the configuration operation because System Lockdown mode is enabled.
- Detailed Description
- The configuration operation cannot be started because the System Lockdown mode is enabled.
- Recommended Response Action
- Make sure that the Lockdown.1#SystemLockdown attribute is set to Disabled and then retry the operation. For information about the Lockdown mode, see the relevant iDRAC Users Guide available on the support site.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC026
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to complete the CoreDump operation on the arg1 device because: arg2.
- Arguments
- arg1 = FQDD
- arg2 = reason
- Detailed Description
- The CoreDump operation on the device cannot be completed because of the issue identified in the message.
- Recommended Response Action
- Review the Lifecycle Log data for information about the update, configuration, or collection job errors. Retry the operation. If the issue persists, contact your service provider.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Warning
- Trap/EventID
- 10282
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC027
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The CoreDump operation on the arg1 device is successfully completed.
- Arguments
- arg1 = FQDD
- Detailed Description
- The CoreDump operation on the device is successfully completed.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Informational
- Trap/EventID
- 10283
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC028
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The CoreDump operation on the arg1 device is successfully started.
- Arguments
- arg1 = FQDD
- Detailed Description
- The CoreDump operation on the device is successfully started. For more information about the status, see the Lifecycle log data.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (NIC = NIC Configuration)
- Severity
- Informational
- Trap/EventID
- 10283
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC100
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The arg1 Port arg2 network link is down.
- Arguments
- arg1 = Controller
- arg2 = Port
- Detailed Description
- The network link is down. Either the network cable is not connected or the network device is not working.
- Recommended Response Action
- Verify that the network port is enabled and if the port has Activity/Speed LEDs, that they are lit. Check the network cable, network cable connections, and the attached network switch.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Warning
- Trap/EventID
- 2090
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC101
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The arg1 Port arg2 network link is started.
- Arguments
- arg1 = controller ID
- arg2 = port ID
- Detailed Description
- The transition from network link not started (down) to network link started (up) has been detected on the NIC controller port identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Trap/EventID
- 2091
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC500
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The requested object is not allowed to be configured if DHCP is enabled.
- Detailed Description
- The values of IP Address is not allowed to change if DHCP is enabled.
- Recommended Response Action
- Disable DHCP and then modify the value.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC501
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The requested object is not allowed to be configured if Auto Config is enabled.
- Detailed Description
- Autoconfig assigns values to the network components.
- Recommended Response Action
- Disable Autoconfig and then modify the value.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC502
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- DHCP is required to be enabled on the NIC before DHCP can be enabled for DNS server or domain name objects.
- Detailed Description
- The value of the specified parameter cannot be changed.
- Recommended Response Action
- Enable DHCP on the NIC before enabling it for DNS.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC503
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The DNS server IP address is not allowed to be configured if DNS server DHCP (cfgDNSServersFromDHCP) is enabled.
- Detailed Description
- The value of the specified parameter cannot be changed.
- Recommended Response Action
- Disable the cfgDNSServersFromDHCP object.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC504
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The IPv6 DNS Server IP address is not allowed to be configured if IPv6 DNS Server DHCP (cfgIPv6DNSServersFromDHCP6) is enabled.
- Detailed Description
- The value of the specified parameter cannot be changed.
- Recommended Response Action
- Disable the cfgIPv6DNSServersFromDHCP6 object.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC505
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The DNS domain name is not allowed to be configured if domain name DHCP (cfgDNSDomainNameFromDHCP) is enabled.
- Detailed Description
- The value of the specified parameter cannot be changed.
- Recommended Response Action
- Disable the cfgDNSDomainNameFromDHCP object.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC506
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- The requested object requires DNS registration to be enabled.
- Detailed Description
- The requested operation requires the DNS registration to be enabled.
- Recommended Response Action
- Enable the DNS registration.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC507
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Unable to determine current NIC state.
- Detailed Description
- For the requested operation, enable the NIC to get the NIC details.
- Recommended Response Action
- Check if the NIC is disabled. If disabled, enable the NIC.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Critical
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC508
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- NIC teaming info is not currently available.
- Detailed Description
- No detailed description available.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Critical
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC509
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- NIC is now ENABLED
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC510
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- NIC is now DISABLED
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC511
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- NIC is already ENABLED
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC512
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- DHCP is already ENABLED
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC513
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- DHCP6 is already ENABLED
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC514
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- DHCP is now ENABLED
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC515
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- DHCP6 is now ENABLED
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
NIC516
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- Static IP configuration enabled and modified successfully
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (NIC = NIC Configuration)
- Severity
- Informational
- Redfish Event Type
- Not Applicable
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\