PowerEdge Servers Error and Event Messages Reference Guide

PDF

SVEP—StorageFabric Validation End Point Event Messages

SVEP0101

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create a Direct Discovery Controller because it already exists.
Detailed Description
The Direct Discovery Controller cannot be created because it already exists.
Recommended Response Action
Delete the existing entry and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0102

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to retrieve or update Direct Discovery Controller because it does not exist.
Detailed Description
The Direct Discovery Controller cannot be retrieved or updated because the entry does not exist.
Recommended Response Action
Enter a valid Direct Discovery Controller ID and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0103

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create an entry because an invalid IP address is entered.
Detailed Description
The entry cannot be created because an invalid IP address is entered.
Recommended Response Action
Enter a valid IP address and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0104

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create an entry because an invalid IP address family type is entered.
Detailed Description
The entry cannot be created because an invalid IP address family type is entered.
Recommended Response Action
Enter a valid IP address family such as IPv4 or IPv6 and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0105

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create an entry because an invalid Transport Type is entered.
Detailed Description
The entry cannot be created because an invalid Transport Type is entered.
Recommended Response Action
Enter a valid transport type and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0106

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create subsystems because it already exists.
Detailed Description
The subsystem cannot be created because it already exists.
Recommended Response Action
Delete the existing Subsystem entry and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0107

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to retrieve or update the subsystem because it does not exist.
Detailed Description
The subsystem cannot be retrieved or updated because the entry does not exist.
Recommended Response Action
Enter a valid subsystem ID and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0108

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create the Host entry because it already exists.
Detailed Description
The host cannot be created because the same entry exists.
Recommended Response Action
Delete the existing Host entry and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0109

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to retrieve or update the host because it does not exist.
Detailed Description
The host cannot be retrieved or updated because the entry does not exist.
Recommended Response Action
Enter a valid host ID and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0110

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create Direct Discovery Controller because license token is not available.
Detailed Description
The Direct Discovery Controller cannot be created because license token is not available.
Recommended Response Action
Retry creating the Direct Discovery Controller later when the license token is freed up.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0111

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to delete the subsystem because it is online.
Detailed Description
The subsystem cannot be deleted because it is online. Only subsystems that are offline or manually added can be deleted.
Recommended Response Action
Make sure that the subsystem is offline and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0112

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to delete the host because it is online.
Detailed Description
The host cannot be deleted because it is online. Only hosts that are offline and manually added can be deleted.
Recommended Response Action
Make sure that the host is offline and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0113

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to delete the Direct Discovery Controller because it is online.
Detailed Description
The Direct Discovery Controller cannot be deleted because it is online. Only Direct Discovery Controllers that are offline can be deleted.
Recommended Response Action
Make sure that the Direct Discovery Controller is offline by deactivatingand retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0114

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to update the Direct Discovery Controller because it is not manually added.
Detailed Description
The Direct Discovery Controller cannot be updated because it is not manually added.
Recommended Response Action
Add Direct Discovery Controller manually and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0115

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to delete the host because this operation is not supported.
Detailed Description
The host cannot be deleted because this operation is not supported.
Recommended Response Action
No response action is required.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0116

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to delete the subsystem because this operation is not supported.
Detailed Description
The subsystem cannot be deleted because this operation is not supported.
Recommended Response Action
No response action is required.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0117

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create the host because the Port ID configuration is non zero.
Detailed Description
The host cannot be created because the host Port ID can only be of value zero.
Recommended Response Action
Either remove the Port ID in the configuration or keep it as zero and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0118

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create the subsystem because the Port ID value in the configuration is out of range.
Detailed Description
The subsystem cannot be created because the Port ID configuration is out of range. The Port ID of the subsystem is in the range of 1 to 65535.
Recommended Response Action
Enter a valid Port ID range (1 to 65535) and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

SVEP0119

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create the host because the Entry Key Type value is used in configuration.
Detailed Description
The host cannot be created because the Entry Key Type is in the given configuration.
Recommended Response Action
Remove the Entry Key Type from the host configuration and retry the operation.
Category
Configuration (SVEP = StorageFabric Validation End Point)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
No alerts are applicable for this message

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\