PowerEdge Servers Error and Event Messages Reference Guide

SWC—Software Config Event Messages

SWC0001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to save the network settings.
Detailed Description: The network cable may not be connected or an internal error occurred. For more information about the failure, see Lifecycle Log.
Recommended Response Action: Verify the network cable is connected and retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set Part Replacement policies.
Detailed Description: The Part Replacement policy configuration operation encountered an unexpected error while communicating with iDRAC.
Recommended Response Action: Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to display the Lifecycle log.
Detailed Description: An unrecoverable error occurred while communicating with iDRAC.
Recommended Response Action: Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to add a work note to the Lifecycle Log.
Detailed Description: The operation to add a work note to the Lifecycle Log encountered an unexpected error while communicating with iDRAC.
Recommended Response Action: Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to display the current hardware inventory.
Detailed Description: The view current hardware inventory operation encountered an unexpected error while communicating with iDRAC.
Recommended Response Action: Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to display the As Shipped hardware inventory.
Detailed Description: The view As Shipped hardware inventory operation encountered an unexpected error while communicating with iDRAC.
Recommended Response Action: Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to write the current hardware inventory to the specified destination.
Detailed Description: The export current hardware inventory operation did not complete because the destination: 1) does not have the specified folder, 2) does not have enough free space, or 3) is read-only.
Recommended Response Action: Retry the operation. If the problem persists, verify the following and retry the operation: 1) Destination has the specified folder. 2) Destination has enough free space. 3) Destination is not write-protected.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to write the As Shipped hardware inventory to the specified destination.
Detailed Description: The export As Shipped hardware inventory operation did not complete because the destination: 1) does not have the specified folder, 2) does not have enough free space, or 3) is read-only.
Recommended Response Action: Retry the operation. If the problem persists, verify the following and retry the operation: 1) Destination has the specified folder. 2) Destination has enough free space. 3) Destination is not write-protected.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully applied front panel security settings.
Detailed Description: The front panel security settings were successfully configured.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the front panel security settings.
Detailed Description: The operation to retrieve the front panel security settings encountered an unexpected error while communicating with iDRAC.
Recommended Response Action: Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to save the front panel security settings.
Detailed Description: The operation to save the front panel security settings encountered an unexpected error while communicating with iDRAC.
Recommended Response Action: Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set new date and time.
Detailed Description: Unable to apply the changes to the date and time settings because an internal error occurred.
Recommended Response Action: Exit the Date and Time wizard and retry the operation. If the problem persists, exit Lifecycle Controller and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the list of supported operating systems.
Detailed Description: The operating system driver pack is missing or not accessible.
Recommended Response Action: Update the system with the latest Lifecycle Controller OS Driver Pack. Obtain the OS Driver Pack from the service provider.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to initialize OS Deployment wizard.
Detailed Description: The operating system driver pack is missing or not accessible.
Recommended Response Action: Exit the OS Deployment wizard and retry the operation. If the problem persists, exit Lifecycle Controller and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0017

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the drivers for the selected operating system.
Detailed Description: An unrecoverable error occurred while retrieving the drivers.
Recommended Response Action: Exit the OS Deployment wizard and retry the operation. If the problem persists, exit Lifecycle Controller and perform an AC power cycle.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0018

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to apply the boot mode settings for BIOS.
Detailed Description: The BIOS boot mode settings could not be applied due to an internal error.
Recommended Response Action: Exit the OS Deployment wizard and retry the operation. If the problem persists, exit the Lifecycle Controller and perform an AC power cycle.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0019

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Test Network Connection operation completed with errors.
Detailed Description: The Test Network Connection ping test timed-out. The network cable is disconnected or the network is not configured correctly.
Recommended Response Action: Check the network cable connection and network configuration settings, then retry the operation. If the problem persists, reconfigure the network settings and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0023

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully configured encryption.
Detailed Description: Encryption configuration is successful.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0024

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Test Network Connection ping test timed-out.
Detailed Description: The Test Network Connection ping test timed-out. The network cable is disconnected or the network is not configured correctly.
Recommended Response Action: Check the network cable connection and network configuration settings, then retry the operation. If the problem persists, reconfigure the network settings and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0025

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The operation completed successfully, however the system is unable to automatically shut down.
Detailed Description: The operation completed successfully, however the system is unable to automatically shut down.
Recommended Response Action: Manually shut down the system. For more information about the failure, see the Lifecycle Log.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0026

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve status of backup Server Profile operation.
Detailed Description: Status of backup Server Profile operation could not be retrieved because an unrecoverable error occurred while communicating with iDRAC.
Recommended Response Action: Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0027

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully backed up a Server Profile by using the Lifecycle Controller GUI.
Detailed Description: The backup Server Profile operation successfully completed.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0028

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The backup Server Profile operation did not successfully complete.
Detailed Description: iDRAC is unable to complete the backup Server Profile operation because an unrecoverable error occurred.
Recommended Response Action: Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0029

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve status of backup Server Profile operation.
Detailed Description: Status of backup Server Profile operation could not be retrieved because an unrecoverable error occurred while communicating with iDRAC.
Recommended Response Action: Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0030

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the backup Server Profile backup operation.
Detailed Description: iDRAC is unable to complete the backup Server Profile operation.
Recommended Response Action: Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0031

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to initiate the backup Server Profile backup operation.
Detailed Description: iDRAC is unable to initiate the backup Server Profile operation because an unrecoverable error occurred.
Recommended Response Action: Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0032

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully exported the Server Configuration Profile image file to the USB drive.
Detailed Description: Exporting the Server Configuration Profile image file to the USB drive was successful.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0033

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully exported the Server Configuration Profile image file to network share.
Detailed Description: Exporting the Server Configuration Profile image file to the network share was successful.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0034

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the file to the network share.
Detailed Description: Lifecycle Controller is unable to export the file to the network share because it has insufficient free space.
Recommended Response Action: Make sure that the network share has sufficient free space then retry the operation. If the problem persists, check network settings and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0035

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to initialize backup Server Profile operation.
Detailed Description: The backup operation did not initialize because the system does not have a service tag.
Recommended Response Action: Assign a service tag to the system and retry the operation. To assign the service tag, If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0036

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to launch hardware diagnostics.
Detailed Description: Unable to launch hardware diagnostics because the Enterprise UEFI Diagnostics application is corrupt or iDRAC is not responding.
Recommended Response Action: Retry the operation. If the problem persists, update the Enterprise UEFI Diagnostics using one of the following methods: 1) Use the Firmware Update feature in Lifecycle Controller. 2) Use the Server Update Utility. 3) Run the Update Package from the operating system. If the problem continues to persist, reset the iDRAC. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0037

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the file to the network share.
Detailed Description: Lifecycle Controller is unable to export the file to the network share because the destination folder is not present or inaccessible.
Recommended Response Action: Make sure that the destination folder is present and accessible, then retry the operation. If the problem persists, check network settings and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0038

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the file to the network share.
Detailed Description: Lifecycle Controller is unable to export the file to the network share because the destination folder is read-only or inaccessible.
Recommended Response Action: Remove the write protection on the destination folder and verify the folder is accessible, then retry the operation. If the problem persists, check network settings and retry.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0039

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to find the backup Server Configuration Profile image.
Detailed Description: The backup Server Configuration Profile image partition is not present in the vFlash SD card.
Recommended Response Action: A backup Server Configuration Profile is required to import or export a Server Profile. Perform the backup operation and retry import or export operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0040

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the Import operation.
Detailed Description: The location of the backup Server Configuration Profile image file provided is incorrect.
Recommended Response Action: Enter the correct location of the backup Server Configuration Profile image file and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0041

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to copy the backup Server Configuration Profile.
Detailed Description: The specified source file location is incorrect.
Recommended Response Action: Make sure that the specified source file location is correct and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0042

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the status of the Import Server Profile operation.
Detailed Description: Lifecycle Controller is unable to retrieve the status of the Import Server Profile operation.
Recommended Response Action: Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0043

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Import Server Profile operation completed with errors.
Detailed Description: The Import Server Profile operation has completed with errors. For more information, see the Lifecycle Log.
Recommended Response Action: Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0044

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the status of the Import Server Profile operation.
Detailed Description: Lifecycle Controller is unable to retrieve the status of the Import Server Profile operation. For more information, see the Lifecycle Log.
Recommended Response Action: Retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0045

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the Import operation.
Detailed Description: The Import operation did not successfully complete. For more information, see the Lifecycle Log.
Recommended Response Action: Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0046

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to initiate Import operation.
Detailed Description: Unable to initiate Import operation since another Import operation is already in progress.
Recommended Response Action: Wait until current Import operation is complete before initiating a new Import operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0047

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Incorrect backup Server Configuration Profile file passphrase provided.
Detailed Description: The passphrase specified is not correct.
Recommended Response Action: Enter the valid passphrase and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0048

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to validate the backup server configuration Profile image file for this system.
Detailed Description: The backup server profile operation did not complete because:1) The backup server configuration profile image file present on the vFlash SD card is invalid for this system.2) The passphrase entered does not match the passphrase used to secure the backup server configuration profile image file.
Recommended Response Action: Do one of the following and retry the operation:1) Reinsert the vFlash SD card with correct backup image file.2) Enter the passphrase that was used to secure the backup server configuration profile image file.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0049

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to continue the Import operation.
Detailed Description: The Import operation cannot continue because backup image file is not present on the vFlash SD card, the image is invalid, or the entered passphrase is incorrect.
Recommended Response Action: Make sure that the backup image file is present on the vFlash SD card, the image is valid, and the entered passphrase is correct.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0050

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to initiate Import operation.
Detailed Description: Unable to initiate Import operation since iDRAC is not responding.
Recommended Response Action: Retry the Import operation using a valid backup image file and the correct passphrase. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0051

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve iDRAC license information.
Detailed Description: Unable to retrieve license information due to an iDRAC communication error.
Recommended Response Action: Exit Lifecycle Controller and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0052

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to continue with OS Deployment operation.
Detailed Description: An error occurred while retrieving the operating system drivers.
Recommended Response Action: Exit the OS Deployment wizard and update the system with the latest operating system driver packs available from the service provider and retry the operation. For more information, see the Lifecycle Controller users guide.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0053

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: File extension is not supported or the Update Package is invalid.
Detailed Description: The file extension of the Update Package is not supported or the Update Package is invalid.
Recommended Response Action: Use a valid Windows-based Update Package with an .exe extension.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0054

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to save settings.
Detailed Description: There was an internal error while saving the settings.
Recommended Response Action: Retry the operation. If the problem persists, reboot the system or update the Lifecycle Controller firmware to the latest version and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0055

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to load the View Current Version page.
Detailed Description: Unable to load the View Current Version page due to an internal error.
Recommended Response Action: Retry the operation. If problem persists, update the iDRAC firmware to the latest version and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0056

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the file to the USB drive.
Detailed Description: Unable to export the file to the USB drive because it does not have the specified folder, does not have enough free space, or is read-only.
Recommended Response Action: Make sure that the USB drive contains the folder specified, has enough free space, or is not read-only. If the problem persists, reboot the system and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0057

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the file to the network share.
Detailed Description: Unable to copy the file to the network share because it does not have the specified folder, the specified folder name has space between the characters, does not have enough free space, or is read-only.
Recommended Response Action: Make sure that the network share has the specified folder, the specified folder name has no space between the characters, has enough free space, or is not read-only. If the problem persists, perform an AC power cycle and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0058

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation.
Detailed Description: An internal processing error occurred.
Recommended Response Action: Reboot the system and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0059

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation.
Detailed Description: The vFlash partitions are being used by other applications such as Lifecycle Controller-Remote Services or RACADM.
Recommended Response Action: Wait until the current operations are complete and retry the operation. For information, see the FAQs section of the Lifecycle Controller-Remote Services or RACADM User Guide.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0060

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation.
Detailed Description: One or more vFlash partitions are attached.
Recommended Response Action: Use iDRAC Web interface to detach the vFlash partitions and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0061

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation.
Detailed Description: Write-protection is enabled on the vFlash SD card.
Recommended Response Action: Remove the write-protection on the vFlash SD card and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0062

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export Lifecycle Log.
Detailed Description: The destination folder is not present, the destination is full or write-protected.
Recommended Response Action: Verify the following and retry the operation: 1) Destination folder is present. 2) Destination has enough free space. 3) Destination is not write-protected. If the problem persists, perform an AC power cycle and retry.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0063

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to authenticate the login credentials and share name.
Detailed Description: The share name and login credentials provided are incorrect.
Recommended Response Action: Enter the correct share name and login credentials, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0064

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to mount the network share.
Detailed Description: The details provided to access the network share are incorrect.
Recommended Response Action: Enter the correct network share details, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0065

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the drivers for the selected operating system.
Detailed Description: Lifecycle Controller is unable to copy the OS drivers from the OS driver pack.
Recommended Response Action: Exit the OS Deployment wizard and retry the operation. If the issue persists, do one of the following:1) Update the system with the latest operating system driver packs using the Firmware Update feature and retry the operation. 2) Reboot the system, press the <F10> key to re-enter Lifecycle Controller, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0066

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to connect to the Network Share.
Detailed Description: Unable to connect to the Network Share due to one of the following: 1) Login credentials entered are incorrect. 2) Network is inaccessible. 3) System IP address conflicts with another system on the network.
Recommended Response Action: Verify the login credentials. Make sure the Network Share is accessible and the system IP address does not conflict with any other system on the network. If the problem persists, perform an AC power cycle and retry.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0067

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to import operating system configuration file.
Detailed Description: The location of the operating system configuration file specified in the operation is not valid.
Recommended Response Action: Make sure that the specified source file path is correct and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0068

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the boot mode settings from BIOS.
Detailed Description: The BIOS boot mode settings could not be retrieved because of an internal issue.
Recommended Response Action: Exit the OS Deployment wizard and retry the operation. If the problem persists, exit Lifecycle Controller and perform an AC power cycle.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0069

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Successfully applied the new boot mode settings for BIOS.
Detailed Description: The new boot mode settings for BIOS were successfully applied.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0070

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SupportAssist collection has been successfully copied to the USB drive.
Detailed Description: The SupportAssist collection has been successfully copied to the USB drive.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0071

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SupportAssist collection has been successfully exported to the network share folder.
Detailed Description: The SupportAssist collection has been successfully exported to the network share folder.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0072

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to export the SupportAssist collection to destination folder.
Detailed Description: SupportAssist collection cannot be exported to the destination folder.
Recommended Response Action: Verify the following and retry the operation: 1) Destination folder is present. 2) Destination folder has sufficient free disk space. 3) Destination folder is not write-protected. If the issue persists, perform an AC power cycle operation, and then retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0073

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start operation with the current iDRAC version.
Detailed Description: The Repurpose or Retire system operation cannot be successfully started because the current version of iDRAC firmware does not support the operation.
Recommended Response Action: Update iDRAC firmware to the latest version and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0074

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start operation with the current iDRAC version.
Detailed Description: The export operation of SupportAssist collection cannot be started because the current version of iDRAC firmware does not support the operation.
Recommended Response Action: Update iDRAC firmware to the latest version and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0075

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform RAID operations because the selected controller is in HBA mode.
Detailed Description: Unable to perform RAID operations because the selected controller is in HBA mode.
Recommended Response Action: Do one of the following: 1) Retry the operation using other controllers that support RAID operations and are not in HBA mode. 2) Change the mode of the controller from HBA mode to RAID mode and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0076

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The following iDRAC internal storage partitions present in the system were not mounted during the system startup: arg1.

Arguments

arg1 = partitions

Detailed Description

Lifecycle Controller detected that the iDRAC internal storage partitions identified in the message were not made available by BIOS during the boot process.

Recommended Response Action

No response action required. If the issue occurs consistently during system startup, restart the iDRAC and then restart the system. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0077

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to initiate the Repurpose or Retire System operation.
Detailed Description: iDRAC is unable to initiate the Repurpose or Retire System operation because the iDRAC is not responding or another operation is in progress.
Recommended Response Action: Retry the operation. If the problem persists, do one the following: 1) Check if there are other operations running on the iDRAC and wait for the operations to complete, and retry the operation. 2) Restart the server, and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0078

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The server has been successfully removed from Integrated Data Center.
Detailed Description: The server has been successfully removed from Integrated Data Center. All configurations will be restored to Factory defaults.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0079

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC entered into Integrated Data Center Troubleshooting Mode.
Detailed Description: iDRAC entered into Dell Integrated Data Center Troubleshooting Mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0080

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC exited from Integrated Data Center Troubleshooting Mode.
Detailed Description: iDRAC exited from Integrated Data Center Troubleshooting Mode. Integrated Data Center may revert some of the network settings made by the user while in Troubleshooting Mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0081

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Integrated Data Center mode enabled.
Detailed Description: Dell Integrated Data Center mode enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0082

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to join Integrated Data Center network.
Detailed Description: An error occurred while joining the Dell Integrated Data Center Network because the Provisioning Server on Integrated Data Center did not respond. Refer to Integrated Data Center setup instructions to setup the Provisioning Server.
Recommended Response Action: Refer to Integrated Data Center User Guide for setup instructions.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0083

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC is successfully removed from the Integrated Data Center network.
Detailed Description: The iDRAC has been successfully removed from Integrated Data Center network per user action. The iDRAC will now be set to Factory defaults. The iDRAC will be able to show up in an Integrated Data Center only when it is rediscovered.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0084

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC successfully joined Integrated Data Center network.
Detailed Description: The iDRAC has successfully joined Integrated Data Center network. This iDRAC will now be managed by the Integrated Data Center solution.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0085

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Integrated Data Center mode is disabled.
Detailed Description: Integrated Data Center Mode is disabled because of one of the following reasons: 1) The feature was disabled 2) The server is not supported for the Integrated Data Center solution 3) The default user credentials on the iDRAC were changed 4) Suppression of the default credentials warning was selected.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0086

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Integrated Data Center Public IP mode is enabled.
Detailed Description: The Public IP access feature has been enabled in iDRAC by the Integrated Data Center solution. The iDRAC can now be managed via the Public IP interface.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0087

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Integrated Data Center Public IP mode is disabled.
Detailed Description: The Public IP access feature in iDRAC is disabled by the Integrated Data Center solution. The iDRAC can no longer be accessed via the public IP interface.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Trap/EventID: 10531
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, IPMI Alert*, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0088

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to retrieve the iDRAC DHCP IP address.
Detailed Description: The DHCP IP address of iDRAC cannot be retrieved because a network cable is not connected or a DHCP server is not functioning.
Recommended Response Action: Make sure that the network cable is connected, DHCP server is turned on, and then retry the operation. If the issue persists, perform the following steps: 1) Turn off the server and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the server, and then retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0089

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to save one or more iDRAC configurations by using the Initial Setup feature of Lifecycle Controller.
Detailed Description: One or more iDRAC configurations cannot be saved by using the Initial Setup feature of Lifecycle Controller.
Recommended Response Action: Make sure that the network cable is connected, DHCP server is turned on, and then retry the operation. If the issue persists, perform the following steps: 1) Turn off the server and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the server, and then retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0090

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC is successfully configured by using the Initial Setup feature of Lifecycle Controller.
Detailed Description: iDRAC is successfully configured by using the Initial Setup feature of Lifecycle Controller.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0091

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to start Lifecycle Controller because of internal issues arg1.

Arguments

arg1 = error code

Detailed Description

The Lifecycle Controller cannot be started because of internal issues.

Recommended Response Action

Restart the server and start Lifecycle Controller by pressing F10 when the company logo is displayed. If the issue persists, update the iDRAC- and BIOS firmware to the latest recommended version, and then retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0092

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the import operation because either the destination folder is unavailable or the folder and file names entered are invalid.
Detailed Description: The import operation cannot be completed because either the destination folder is unavailable or the folder and file names entered are invalid.
Recommended Response Action: Make sure that the following are correct and retry the operation: 1) The destination folder is available and accessible. 2) The destination folder and file name entered are valid. If the issue persists, check the network setting by using the Lifecycle Controller graphical interface.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0093

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Encryption configuration successfully deleted.
Detailed Description: Encryption configuration successfully deleted.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0094

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform Retire or Repurpose operation as Secure Enterprise Key Manager (SEKM) is not disabled on iDRAC.
Detailed Description: The Retire and Repurpose operation cannot be performed because the Secure Enterprise Key Manager (SEKM) feature is enabled on iDRAC.
Recommended Response Action: Disable the SecureEnterprise Key Manager (SEKM) feature and then retry the operation. Forinformation about disabling SEKM, refer to the iDRAC Users Guide available onthe support site.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0101

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to read available log records.
Detailed Description: Racadm is unable to read the available log records at this point. Retry the command.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0102

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -m option is not supported by the interface being used.
Detailed Description: The option requested is not available on the interface being used.
Recommended Response Action: Refer to the help to get the list of options valid for the interface.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0103

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -E option is not valid for the specified log.
Detailed Description: The specified log does not take in the -e option.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0104

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -R option is not valid for the specified log.
Detailed Description: The specified log does not take in the -r option.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0105

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid -m option. Try --more or refer help for proper usage.
Detailed Description: The command does not take in the -m option.
Recommended Response Action: Refer the help text for getraclog command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0106

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -u option is not supported on the current RAC configuration.
Detailed Description: The specified option is not supported on the RAC.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0107

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: More than one option is not allowed with this command.
Detailed Description: The command takes in only one option which is the Session ID.
Recommended Response Action: Enter the command only with one option i.e. the Session ID.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0108

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The service tag is not currently populated.
Detailed Description: The Service Tag string is empty.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0109

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No process information is currently available.
Detailed Description: There is no RAC diagnostic information available.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0110

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No build information is currently available.
Detailed Description: The build information is not available for racdump.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0111

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A server action command must be specified.
Detailed Description: The serveraction subcommand requires an option to be specified.
Recommended Response Action: Refer the help for serveraction subcommand, and enter a valid option.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0112

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Timeout while waiting for server to perform requested power action.
Detailed Description: A network time-out occurred while trying to perform the power action.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0113

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -6 option can only be used in combination with the -d or -s option.
Detailed Description: The syntax of the setniccfg command is invalid.
Recommended Response Action: Refer the help text for setniccfg subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0114

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -o option cannot be used with any other options.
Detailed Description: The syntax of the setniccfg command is invalid.
Recommended Response Action: Refer the help text for setniccfg subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0115

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -s option cannot be used with any other options.
Detailed Description: The syntax of the setniccfg command is invalid.
Recommended Response Action: Refer the help text for setniccfg subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0116

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -s option requires IP address, subnet mask, and gateway.
Detailed Description: The syntax of the setniccfg command is invalid.
Recommended Response Action: Refer the help text for setniccfg subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0117

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. Both -f and -t must be specified.
Detailed Description: Invalid parameters passed to the function.
Recommended Response Action: Refer the help text for sslcertdownload subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0118

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. -f must be specified.
Detailed Description: The syntax of the sslcertupload command is invalid.
Recommended Response Action: Refer the help text for sslcertupload subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0119

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid certificate type specified with -t option.
Detailed Description: The syntax of the sslcertview command is invalid.
Recommended Response Action: Refer the help text for sslcertview subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0120

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. Certificate type (-t) must be specified.
Detailed Description: The syntax of the sslcertview command is invalid.
Recommended Response Action: Refer the help text for sslcertview subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0121

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. User index (-i) must be specified.
Detailed Description: The syntax of the sslcertview command is invalid.
Recommended Response Action: Refer the help text for sslcertview subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0122

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. SSL key type (-t) must be specified.
Detailed Description: The syntax of the sslcertupload command is invalid.
Recommended Response Action: Refer the help text for sslcertupload subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0123

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -s option is not valid with any other options.
Detailed Description: The syntax of the sslcsrgen command is invalid.
Recommended Response Action: Refer the help text for sslcsrgen subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0124

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -u option requires -f to be specified.
Detailed Description: The syntax of the sslcsrgen command is invalid.
Recommended Response Action: Refer the help text for sslcsrgen subcommand.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0125

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate CSR.
Detailed Description: The CSR file could not be generated.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0126

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to download CSR file.
Detailed Description: Racadm tool was unable to download the generated CSR file.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0127

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to open file for writing.
Detailed Description: The file may be write protected and hence could not be edited.
Recommended Response Action: Check if the file is write protected.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0128

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Common Name (CN) field of the CSR Security group must be configured before a CSR can be generated.
Detailed Description: The Common Name field is necessary for generating a CSR. It is not generated if Common Name is empty.
Recommended Response Action: Configure the Common Name field by using config command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0129

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to send test email. Please make sure that your email alerts have been configured correctly and connectivity to the SMTP server exists.
Detailed Description: Racadm tool was not able to send a test email for the configuration.
Recommended Response Action: Check for the parameters mentioned in the message.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0130

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Trap at specified index is not currently enabled.
Detailed Description: The Trap needs to be set for the particular index for the testtrap to go through.
Recommended Response Action: Set cfgIpmiPetAlertEnable in cfgIpmiPet group using config subcommand for the corresponding index.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0131

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Trap destination address must be configured.
Detailed Description: The destination Ip address must be configured for the Trap.
Recommended Response Action: Set cfgIpmiPetAlertDestIpAddr in cfgIpmiPet group using config subcommand for the corresponding index.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0132

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to send test trap. Please make sure that your trap has been configured correctly and connectivity to the destination endpoint exists.
Detailed Description: Either the destination Ip address is not reachable or the required values are not configured.
Recommended Response Action: Check for the connectivity to the configured Ip address.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0133

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Either connect or disconnect must be specified.
Detailed Description: Insufficient information provided.
Recommended Response Action: Specify either the connect or the disconnect option with the subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0134

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The RAC log was cleared successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0135

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SEL was cleared successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0136

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Object value modified successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0137

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The coredump was deleted successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0138

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Coredump request completed successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0139

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Total Records: arg1

Arguments

arg1 = Number of Records

Detailed Description

Success message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0140

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: RAC reset operation initiated successfully. It may take up to a minute for the RAC to come back online again.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0141

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Certificate successfully downloaded from the RAC
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0142

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 certificate is successfully uploaded to iDRAC. For more information about the certificate, run the following command at the RACADM Command Line Interface (CLI):Racadm get idrac.securitycertificate.arg2.

Arguments

arg1 = certificate Name
arg2 = index

Detailed Description

The certificate identified in the message is successfully uploaded. For more information about the certificate, run the following command at the RACADM Command Line Interface (CLI): Racadm get idrac.securitycertificate.[index]. The index range is 164.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0143

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: SSL key successfully uploaded to the RAC.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0144

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Certificate successfully uploaded to the RAC. The RAC will now reset to enable the new certificate and may be offline temporarily.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0145

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A CSR was generated successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0146

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Last ASR screen was cleared successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0147

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: ASR request completed successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0148

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Test email sent successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0149

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Test trap sent successfully.
Detailed Description: The requested SNMP test trap alert was successfully sent.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0150

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Object value is valid
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0151

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: RAC configuration saved to file successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0152

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: RAC configuration from file completed successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0153

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: RAC configuration file is valid
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0154

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Generating CSR. Please wait.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0155

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: CSR generated and downloaded from RAC successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0156

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: CSR file downloaded from RAC successfully
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0157

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: User certificate successfully uploaded to the RAC.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0158

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: User CA certificate successfully uploaded to the RAC.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0159

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Kerberos Keytab successfully uploaded to the RAC.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0160

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: PK SSH Authentication Key file successfully uploaded to the RAC.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0161

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: PK SSH Authentication operation completed successfully.
Detailed Description: Success message.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0163

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Secured Component Verification (SCV) Delta Certificate with the serial number arg1 is successfully uploaded to iDRAC.

Arguments

arg1 = certificate_serial_no

Detailed Description

The Secured Component Verification (SCV) Delta Certificate with the serial number identified in the message is successfully uploaded to iDRAC.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0164

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Secured Component Verification (SCV) Delta Certificate with the serial number arg1 is successfully deleted from iDRAC.

Arguments

arg1 = certificate_serial_no

Detailed Description

The Secured Component Verification (SCV) Delta Certificate with the serial number identified in the message is successfully deleted from iDRAC.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0171

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to successfully complete the proof-of-possession challenge operation because an invalid Hash-based Message Authentication Code (HMAC) is entered.
Detailed Description: The proof-of-possession challenge operation cannot be completed because an invalid Hash-based Message Authentication Code (HMAC) is entered.
Recommended Response Action: Make sure that the client device calculates and invokes the proof-of-possession challenge operation again.
Category: Audit (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0172

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the proof-of-possession challenge operation because the public/private key algorithm could not be successfully run.
Detailed Description: The proof-of-possession challenge operation cannot be completed because the public/private key algorithm could not be successfully run.
Recommended Response Action: Make sure that the client device is sending valid challenge values, and retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Audit (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0201

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: All keys successfully deleted
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0202

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Key successfully deleted
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0203

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Key file successfully uploaded
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0204

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Key text successfully uploaded
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0205

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Upload an SSL key to the RAC
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0206

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: View user certificate information
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0207

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Display the version info of RACADM
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0208

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Disconnect Virtual Media connections
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0209

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Connect or disconnect image server connections
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0210

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Display NIC teaming information
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0211

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Perform vFlash operations
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0212

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Perform POST Virtual Console disable from local system
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0213

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Disable the Virtual Console from a local Console
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0214

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Makes a remote ISO image available to the server
Detailed Description: Help Text.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0215

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Disable Remote File Started. Please check status using -s option to know Remote File Share is ENABLED or DISABLED.
Detailed Description: The process to disable the file share has started. Use the -s option to know more about the status.
Recommended Response Action: If required check the status using the -s option.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0216

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -c option requires -l to also be specified.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0217

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -c option requires -u to also be specified.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0218

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -c option requires -p to also be specified.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0219

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -p option requires -c to also be specified.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0220

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -u option requires -c to also be specified.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0221

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -l option requires -c to also be specified.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0222

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -d option is not valid with -c.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0223

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -d option is not valid with -p.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0224

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -d option is not valid with -u.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0225

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -d option is not valid with -l.
Detailed Description: The syntax of the command is incorrect.
Recommended Response Action: Refer to the help for remote image command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0226

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No valid directory service certificate exists
Detailed Description: The Remote/Firmware racadm did not find any AD/LDAP certificate at specified path.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0227

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Partition label exceeds maximum limit of 6 alphanumeric characters.
Detailed Description: Invalid values passed to the function.
Recommended Response Action: Enter a shorter path to the firmware image file.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0228

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Partition label must be an alphanumeric character string.
Detailed Description: Invalid values passed to the function.
Recommended Response Action: Enter a shorter Partition label.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0229

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Some Necessary tag(s) are missing: -i -o -e -t -f & -s must be specified for create partition.
Detailed Description: Insufficient arguments passed to the command.
Recommended Response Action: Refer the help text for vflashpartition command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0230

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: vFlash not enabled.
Detailed Description: vFlash is not enabled. This may be because the user does not have enough privileges.
Recommended Response Action: Enable vFlash and re-try.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0231

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Partition of type \"image\" not supported on local racadm.
Detailed Description: The partition image type specified is not available on local racadm.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0232

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Remote RACADM commands are not supported on this iDRAC. To upgrade your iDRAC version, contact your service provider.
Detailed Description: Remote RACADM commands are not supported on the current iDRAC.
Recommended Response Action: If remote RACADM is a necessity, upgrade the iDRAC version.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0233

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No indexes are available to configure additional groups.
Detailed Description: Indexed groups in the configuration file is more than the indexed groups in iDRAC.
Recommended Response Action: Verify if the number of indexed groups available in iDRAC match the indexed groups in the configuration file. If it does not match, either reset the unnecessary indexes on iDRAC or remove the extra groups from the configuration file.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0234

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Remote host is not reachable or connection is interrupted.
Detailed Description: The remote host specified for the ftp update is not reachable.
Recommended Response Action: Check the connectivity between iDRAC and the remote host used for the ftp update.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0235

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: All keys successfully deleted.
Detailed Description: All public keys stored on the iDRAC have been deleted.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0236

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Key successfully deleted.
Detailed Description: The specified public key was deleted from iDRAC.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0237

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Key text appears to be corrupted.
Detailed Description: The key text in the public key specified is corrupt.
Recommended Response Action: Request for a valid public key from the system and re-try the command.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0238

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Key is too long.
Detailed Description: The key specified by the public key is too long.
Recommended Response Action: Request for a valid public key from the system and re-try the command.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0239

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The requested object is not allowed to be configured if IPv6 AutoConfig is enabled.
Detailed Description: The requested object is auto-assigned if IPv6 AutoConfig is enabled, and hence cannot be configured.
Recommended Response Action: Disable IPv6 AutoConfig and re-try the command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0240

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The IPv6 DNS Server IP address is not allowed to be configured if IPv6 DNS Server DHCP (cfgIPv6DNSServersFromDHCP6) is enabled.
Detailed Description: The requested object is auto-assigned if DNS Server DHCP is enabled, and hence cannot be configured.
Recommended Response Action: Disable DNS Server DHCP and re-try the command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0241

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Power Cap Enable not set. Unable to modify this property.
Detailed Description: To modify this property, set the Power Cap Enable option.
Recommended Response Action: Set the Power Cap Enable object and modify the required property.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0242

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A required license is missing or expired. Obtain an appropriate license and try again, or contact your service provider for additional details.
Detailed Description: The license is missing or expired. This will result in the loss of functionality that is specific to the features supported by the license.
Recommended Response Action: Import an appropriate license. If you do not know which license to import. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0243

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Certificate regenerated successfully and webserver restarted
Detailed Description: SSL Certificate is regenerated successfully and the Web server is restarted.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0244

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid Fully Qualified Device Descriptor (FQDD).
Detailed Description: The specified Fully Qualified Device Descriptor (FQDDs) system component name is invalid.
Recommended Response Action: Verify that the correct Fully Qualified Device Descriptor (FQDD) system component name is specified. See the help text (The help text for the get subcommand can be obtained by running "racadm help get") or documentation for valid FQDD system component names.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0245

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Failed to set object value because local configuration using RACADM is disabled.
Detailed Description: Local configuration using RACADM is disabled. This limits local configuration privileges such as resetting object values.
Recommended Response Action: Within group cfgRacTuning set the property cfgRacTuneLocalConfigDisable to 0.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0246

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Value specified is invalid: Valid range is arg1.

Arguments

arg1 = index

Detailed Description

The specified value is outside of the valid range.

Recommended Response Action

Verify that a valid value is specified. See the help text or documentation for valid values.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0247

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid subcommand specified.
Detailed Description: An invalid subcommand was entered.
Recommended Response Action: Refer the list of subcommands.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0248

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid command syntax.
Detailed Description: The specified command has invalid syntax.
Recommended Response Action: Verify that the correct command syntax is specified. See the help text or documentation for valid commands.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0249

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid syntax. The requested subcommand requires -i arg1 to be specified.

Arguments

arg1 = index

Detailed Description

The specified parameter needs to be given with its legal value.

Recommended Response Action

Enter the proper index preceded by -i.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0250

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The specified subcommand does not require any options.
Detailed Description: Extra parameters were passed.
Recommended Response Action: Enter the subcommand without any options.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0251

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid index value. Only index values arg1 - arg2 are permitted.

Arguments

arg1 = number
arg2 = number

Detailed Description

The value of specified parameter is invalid.

Recommended Response Action

Enter the index value as specified by the message.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0252

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No options were specified. The subcommand requires options to be used.
Detailed Description: Invalid number of arguments were passed to the command.
Recommended Response Action: Refer the help text for the command, and enter the required parameters.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0253

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to allocate memory needed to perform operation.
Detailed Description: Unable to allocate memory to perform the operation, see the inserted comment.
Recommended Response Action: Power Cycle the system and re-enter the command.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0254

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform requested operation. If the operation attempted was to configure DRAC, possible reason may be that Local Configuration using RACADM is disabled.
Detailed Description: Local Configuration using RACADM may be disabled.
Recommended Response Action: Check if the Local Configuration using RACADM is disabled and enable it through GUI.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0255

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to open file.
Detailed Description: Unable to open the specified file.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0256

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to read file.
Detailed Description: Unable to read the specified file.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0257

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. Too many options specified.
Detailed Description: Invalid number of arguments were passed to the command.
Recommended Response Action: Refer the help text for the command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0258

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Insufficient resources to perform operation.
Detailed Description: Insufficient resources to execute the command.
Recommended Response Action: Power Cycle the system and re-enter the command.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0259

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid group specified.
Detailed Description: The value of specified parameter is invalid.
Recommended Response Action: Refer the list of groups and enter a valid option.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0260

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid object specified.
Detailed Description: The value of specified parameter is invalid.
Recommended Response Action: Refer the list of objects in the corresponding group.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0261

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified option is not supported with the interface being used.
Detailed Description: The option requested is not available on the interface being used.
Recommended Response Action: Refer to the help to get the list of commands/options valid for the interface.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0262

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform operation. Please make sure RAC controller and appropriate IPMI drivers are installed.
Detailed Description: The IPMI drivers or the RAC controller may not be installed.
Recommended Response Action: Check if the required modules are installed.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0263

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Specified path is too long.
Detailed Description: The length of path to the firmware image is longer than the specified value.
Recommended Response Action: Enter a shorter path to the firmware image file.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0264

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Resource currently in use by another process. Please retry again later.
Detailed Description: The resources required for the execution are in use by another process.
Recommended Response Action: Wait for the process to release the resources and try again.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0265

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: This option is not supported on this type of DRAC.
Detailed Description: The option requested is not available on the DRAC being used.
Recommended Response Action: Refer to the help to get the list of commands/options valid for the DRAC.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0266

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the requested operation. Make sure SD card is inserted.
Detailed Description: The SD card may not be inserted/inserted properly.
Recommended Response Action: Ensure that the SD card is inserted in the server.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0267

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to perform the requested operation. Make sure a non write protected SD card is inserted.
Detailed Description: Unable to edit the SD card, since it is write protected.
Recommended Response Action: Check if the SD card is write protected. If yes, disable the write protection.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0268

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: There is no ASR screen currently available to clear
Detailed Description: The ASR screen is already cleared.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0269

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to clear the RAC log. Possible reason may be that Local Configuration using RACADM is disabled.
Detailed Description: Local Configuration using RACADM may be disabled.
Recommended Response Action: Check if the Local Configuration using RACADM is disabled and enable it through GUI.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0270

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to clear the SEL. Possible reason may be that Local Configuration using RACADM is disabled.
Detailed Description: Local Configuration using RACADM may be disabled.
Recommended Response Action: Check if the Local Configuration using RACADM is disabled and enable it through GUI.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0271

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -f option is only valid with -p and -c.
Detailed Description: The syntax for the config command is invalid.
Recommended Response Action: Refer to the help text for the config subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0272

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -g option is only valid with -o, -i, and -c.
Detailed Description: The syntax for the config command is invalid.
Recommended Response Action: Refer to the help text for the config subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0273

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -g option requires -o to also be specified.
Detailed Description: The syntax for the config command is invalid.
Recommended Response Action: Refer to the help text for the config subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0274

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. An object value must be specified.
Detailed Description: The value of specified parameter is invalid.
Recommended Response Action: Enter the same command with a legal value to the object.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0275

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -c option is only valid with -f or -g.
Detailed Description: The syntax for the config command is invalid.
Recommended Response Action: Refer to the help text for the config subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0276

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -p option is only valid with -f.
Detailed Description: The syntax for the config command is invalid.
Recommended Response Action: Refer to the help text for the config subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0277

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -i option is only valid with -g and -o.
Detailed Description: The syntax for the config command is invalid.
Recommended Response Action: Refer to the help text for the config subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0278

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid group or object specified.
Detailed Description: The value of specified parameter is invalid.
Recommended Response Action: Enter the values for the group name and object name correctly.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0279

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified group is not indexed and does not support -i.
Detailed Description: The group is not indexed and does not require an index to be specified.
Recommended Response Action: Enter the command without the index.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0280

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The indexed group specified requires -i arg1.

Arguments

arg1 = index

Detailed Description

The group is indexed and an index needs to be specified.

Recommended Response Action

Enter the command with a valid index for the group.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0281

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified object is READ ONLY and cannot be modified.
Detailed Description: The value being modified is READ only.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0282

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified object is READ ONLY for this index and cannot be modified.
Detailed Description: The value being modified is READ only.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0283

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified object value is not valid.
Detailed Description: The value given for the object is not valid.
Recommended Response Action: Enter a valid value for the corresponding object.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0284

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Failed to set the object value. Possible reason may be that Local Configuration using RACADM is disabled.
Detailed Description: Local Configuration using RACADM may be disabled.
Recommended Response Action: Check if the Local Configuration using RACADM is disabled and enable it through GUI.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0285

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Object value is invalid.
Detailed Description: The value given for the object is not valid.
Recommended Response Action: Enter a valid value for the corresponding object.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0286

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Modifying the user configuration at index 1 is not allowed.
Detailed Description: Objects in the cfgUserAdmin group corresponding to index 1 cannot be modified.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0287

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid entry in configuration file.
Detailed Description: The value of a parameter in the config file is invalid.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0288

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Object arg1 in arg2 group must be specified. Line: arg3

Arguments

arg1 = object name
arg2 = group name
arg3 = line no.

Detailed Description

The object specified in the message in the group specified in the message is not configured.

Recommended Response Action

Configure the object specified in the message in specified group, before performing a config to file action.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0289

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Invalid value in config file. Group: arg1, Object: arg2, Value: \"arg3\", Line [arg4}

Arguments

arg1 = Group Name
arg2 = Object Name
arg3 = Value
arg4 = Line No.

Detailed Description

The specified object value is invalid.

Recommended Response Action

Configure the specified object and assign a valid value.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0290

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Failed to configure object. Group: arg1, Object : arg2

Arguments

arg1 = Group Name
arg2 = Object Name

Detailed Description

Failed to configure the object specified in the error message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0291

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Another object exists with the specified value. Duplicate values are not allowed for the requested object.
Detailed Description: Another object of the same value exists. Typically in the case of username.
Recommended Response Action: Change the specified value and re-try.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0292

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The specified object at index arg1 does not exist.

Arguments

arg1 = index number

Detailed Description

The queried object does not exist at the specified index.

Recommended Response Action

Check for the objects available at the specified index and re-try.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0293

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified object is not recognized by iDRAC.
Detailed Description: The specified object is not present in the iDRAC.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0294

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid group name specified.
Detailed Description: The group name specified is incorrect.
Recommended Response Action: Refer to the list of groups available and choose the correct one.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0295

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid object name specified.
Detailed Description: The object name specified is incorrect.
Recommended Response Action: Refer to the list of objects in the group and choose the correct one.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0296

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified value is not allowed to be configured if the user name or password is blank.
Detailed Description: Either the password field or the username field is empty.
Recommended Response Action: Enter the command with the username and password.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0297

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to remove passwords because file could not be saved.
Detailed Description: After the Groups are downloaded to a file, the passwords are to be deleted.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0298

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified object value cannot be configured if local configuration is disabled or smart card logon is enabled. If smart card logon is enabled, serial, SSH and IPMI over LAN is disabled by force and cannot be enabled.
Detailed Description: The specified object value cannot be configured if local configuration is disabled or smart card logon is enabled. If smart card logon is enabled, serial, SSH and IPMI over LAN is disabled by force and cannot be enabled.
Recommended Response Action: Enable Local Configuration (through GUI) or Disable Smart Card Logon to change the value.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0299

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Destination Email Address is invalid.
Detailed Description: The Email Address provided is invalid.
Recommended Response Action: Specify a valid Email address.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0300

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: There is no coredump currently available.
Detailed Description: There is no coredump available to display.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0301

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified IP address is not valid.
Detailed Description: The IP address provided is not valid.
Recommended Response Action: Specify a valid IP Address.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0302

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -s option is not valid with any other option.
Detailed Description: The syntax of the fwupdate command is invalid.
Recommended Response Action: Refer the help text for fwupdate subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0303

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -r option is not valid with any other option.
Detailed Description: The syntax of the fwupdate command is invalid.
Recommended Response Action: Refer the help text for fwupdate subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0304

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -g option requires -u to also be specified.
Detailed Description: The syntax of the fwupdate command is invalid.
Recommended Response Action: Refer the help text for fwupdate subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0305

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -p option requires -u to also be specified.
Detailed Description: The syntax of the fwupdate command is invalid.
Recommended Response Action: Refer the help text for fwupdate subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0306

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -a option requires -g and -u to also be specified.
Detailed Description: The syntax of the fwupdate command is invalid.
Recommended Response Action: Refer the help text for fwupdate subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0307

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -d option requires -p or -g to also be specified.
Detailed Description: The syntax of the fwupdate command is invalid.
Recommended Response Action: Refer the help text for fwupdate subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0308

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -d option requires -g to also be specified.
Detailed Description: The syntax of the fwupdate command is invalid.
Recommended Response Action: Refer the help text for fwupdate subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0309

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -p option is not supported with the interface being used.
Detailed Description: The platform does not support the specified functionality of fwupdate.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0310

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -f is not valid with the option specified.
Detailed Description: The syntax of the getconfig command is invalid.
Recommended Response Action: Refer the help text for getconfig subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0311

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -g option is only valid with -i and -o options.
Detailed Description: The syntax of the getconfig command is invalid.
Recommended Response Action: Refer the help text for getconfig subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0312

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -u option is not valid with any other options.
Detailed Description: The syntax of the getconfig command is invalid.
Recommended Response Action: Refer the help text for getconfig subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0313

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -h option is not valid with any other options.
Detailed Description: The syntax of the getconfig command is invalid.
Recommended Response Action: Refer the help text for getconfig subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0314

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Invalid syntax. The -o option requires -g to be specified also.
Detailed Description: The syntax of the getconfig command is invalid.
Recommended Response Action: Refer the help text for getconfig subcommand.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0315

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Failed to get object value.
Detailed Description: The getconfig subcommand failed to get the object value.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0316

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The index must be greater than 0.
Detailed Description: The value for index must be greater than zero.
Recommended Response Action: Enter a positive value for index.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0317

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The number of records to display must be greater than zero.
Detailed Description: The value for -c must be greater than zero.
Recommended Response Action: Enter a value greater than zero, for the option -c.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0318

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The starting record must be greater than zero.
Detailed Description: The value for -s must be greater than zero.
Recommended Response Action: Enter a value greater than zero, for the option -s.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0319

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The -i option is not valid with any other options.
Detailed Description: The syntax for the getraclog command is invalid.
Recommended Response Action: Refer the help text for getraclog command.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0320

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to get the number of records available.
Detailed Description: Racadm tool failed to get the total number of records.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0321

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to open the log for reading.
Detailed Description: Could not open the log file for reading.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0322

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Starting record specified exceeds number of records available.
Detailed Description: The starting record value has to be lesser than the number of records available.
Recommended Response Action: Get the number of records available, and then run the command. If the command is gettracelog, try executing the command again.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0323

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Number of records specified exceeds number of records available.
Detailed Description: The number of records specified to be displayed should be lesser than number of records available.
Recommended Response Action: Get the number of records available, and then run the command.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0324

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: There are no records available to display.
Detailed Description: There are no records to display. This might be a result of the log being cleared.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0325

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The specified object is WRITE-ONLY and cannot be displayed.
Detailed Description: The requested property is write-only.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0400

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The IP blocking range arg1 is arg2 with arg3/arg4 by arg5.

Arguments

arg1 = range numbers
arg2 = enablmentStatus
arg3 = IP address
arg4 = netmask
arg5 = userName

Detailed Description

The IP blocking range is modified.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0401

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The certificate of the 802.1X Authentication Server is valid.
Detailed Description: The certificate of the 802.1X Authentication Server is valid.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0402

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The certificate of the 802.1X Authentication Server is invalid.
Detailed Description: The certificate of the 802.1X Authentication Server is invalid.
Recommended Response Action: The issue does not necessarily affect 802.1X authentication, but could indicate a misconfiguration of either the iDRAC or the network switch it is connected to, or that the Authentication Server has been compromised. Do the following: 1) Check the configuration of the etherswitch that the iDRAC is connected to. Ensure that it is using the expected 802.1X Authentication Server. 2) Verify that the certificate installed on the iDRAC for Authentication Server validation is correct and matches the signing authority for that Authentication Servers certificate, and that none of the certificates have expired. 3) Check the configuration and logs of the Authentication Server to ensure it is operating properly and no security issues exist.
Category: Audit (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0403

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 certificate is successfully downloaded from iDRAC.

Arguments

arg1 = certificate_name

Detailed Description

The certificate identified in the message is successfully downloaded from iDRAC.

Recommended Response Action

No response action required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0404

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to download the arg1 certificate from iDRAC.

Arguments

arg1 = certificate_name

Detailed Description

The certificate identified in the message could not be downloaded from iDRAC for the following reasons. 1. Certificate does not exist. 2. Certificate expired 3. Certificate got corrupted on the system. 4. Error in reading from system memory.

Recommended Response Action

Make sure the system has the valid certificate and retry the operation. If issue still persists contact system administrator.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0700

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC is not ready. The configuration values cannot be accessed. Please retry after a few minutes.
Detailed Description: iDRAC7 is not ready or is busy and is not responding to iDRAC7 Settings IPMI requests.
Recommended Response Action: Turn off the system, Remove AC. Wait for 5 seconds. Connect AC. Turn it on.
Category: System Health (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0701

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Power capping is enabled.
Detailed Description: Power capping is enabled and sets user-defined power capping limits for the system.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0702

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Power capping is disabled.
Detailed Description: Power capping is disabled and sets recommended limits for the system.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0717

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC Local Configuration is disabled. iDRAC Settings are accessed in read-only mode.
Detailed Description: For security reasons, the local configuration is disabled. Enable local configuration from the iDRAC Web interface.
Recommended Response Action: Enable iDRAC local configuration from iDRAC Web interface.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0722

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Error occurred while resetting to defaults. The reset command was not accepted.
Detailed Description: iDRAC is processing a previous reset to default command.
Recommended Response Action: Retry after a few minutes.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0723

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Error occurred while Resetting to defaults. The Reset status is not available.
Detailed Description: iDRAC is not responding to the current Reset status query.
Recommended Response Action: Retry after a few minutes.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0724

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Error occurred while Resetting to defaults due to a timeout.
Detailed Description: Resetting to defaults did not complete within the maximum process allotted time.
Recommended Response Action: Retry after a few minutes.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0725

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC communication failure.
Detailed Description: iDRAC is busy and does not respond to iDRAC configurator IPMI requests.
Recommended Response Action: Try AC power cycling the server or upgrade the iDRAC firmware.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC0726

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to import the arg1 certificate, because either the certificate is invalid, expired, or has a key mismatch issue.

Arguments

arg1 = certificate Name

Detailed Description

The certificate identified in the message cannot be imported, because either the certificate is invalid, expired, or has a key mismatch issue.

Recommended Response Action

Make sure the certificate is valid and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC0727

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to set the entered attribute because the SNMP user authentication passphrase or SNMP user privacy passphrase is not configured.
Detailed Description: The entered attribute cannot be set because the SNMP user authentication passphrase or SNMP user privacy passphrase is not configured.
Recommended Response Action: Enter the authentication passphrase and privacy passphrase and retry the operation. To set the passphrase values by using the RACADM Command Line Interface (CLI), enter, "racadm set idrac.users.n.SNMPv3AuthenticationPassphrase value" and "racadm set idrac.users.n.SNMPv3PrivacyPassphrase value". Here, value is a string. To set by using the iDRAC GUI, click iDRAC Settings > Users > Local Users > Edit User.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1903

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: RAC SSL Certificate has been changed.
Detailed Description: RAC SSL Certificate has been changed.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1905

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: RAC Virtual Console configuration has been changed.
Detailed Description: RAC Virtual Console configuration has been changed.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1908

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the operation because the default password is still in use and must be changed.
Detailed Description: The operation cannot be completed because the default password for the default user is still in use on the iDRAC.
Recommended Response Action: Change the default password for the default user using one of the iDRAC interfaces. For more information, refer interface User Guides.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1909

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

User ID arg1 RAC Privilege has been changed.

Arguments

arg1 = username

Detailed Description

The privilege level of the iDRAC User ID indicated in the message has been changed.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1910

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

User ID arg1 User Name has been changed.

Arguments

arg1 = username

Detailed Description

User ID Name has been changed.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Trap/EventID

10531

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1911

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

User ID arg1 User Password has been changed.

Arguments

arg1 = username

Detailed Description

User ID Password has been changed.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Trap/EventID

10531

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1912

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

User ID arg1 User Access Right has been changed.

Arguments

arg1 = username

Detailed Description

User ID Access Right has been changed.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Trap/EventID

10531

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1913

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Network Time Protocol configuration is enabled.
Detailed Description: Network Time Protocol configuration is enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1914

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Network Time Protocol configuration is disabled.
Detailed Description: Network Time Protocol configuration is disabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1915

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC time zone has changed.
Detailed Description: iDRAC time zone has changed.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1916

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Network Time Protocol server configuration has changed.
Detailed Description: Network Time Protocol server configuration has changed.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1917

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: HTTPS redirection is disabled.
Detailed Description: HTTP to HTTPS redirection is disabled. Any iDRAC connection made over the HTTP port (default port number 80) will no longer be redirected to the secure HTTPS port (default port number 443). This will make the connections insecure as the data transmitted over the port is no longer encrypted.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1918

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: HTTPS redirection is enabled.
Detailed Description: HTTP to HTTPS redirection is enabled. Any iDRAC connection made over the HTTP port (default port number 80) will be redirected to the secure HTTPS port (default port number 443).
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1920

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Chassis Management/Management Module at Server Mode is enabled.
Detailed Description: The Chassis Management/Management Module at Server Mode is enabled.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1921

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Chassis Management/Management Module at Server Mode is disabled.
Detailed Description: The Chassis Management/Management Module at Server Mode is disabled.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1922

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

User arg1 has successfully modified the configuration by using Quick Sync.

Arguments

arg1 = user name

Detailed Description

The user identified in the message has successfully modified the configuration by using Quick Sync.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Trap/EventID

10531

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1923

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to modify the configuration by using Quick Sync because invalid credentials are entered.
Detailed Description: The configuration cannot be modified by using Quick Sync because invalid credentials are entered.
Recommended Response Action: Make sure that correct user name and password are entered, and then retry the operation.
Category: Audit (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1924

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to modify the configuration by using Quick Sync.
Detailed Description: The configuration cannot be modified by using Quick Sync because issues were found with the configuration information.
Recommended Response Action: Review the configuration operation results and correct any issues detected, then retry the operation.
Category: Audit (SWC = Software Config)
Severity: Warning
Trap/EventID: 8482
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1925

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Quick Sync access feature is set to the Disabled mode.
Detailed Description: The iDRAC Quick Sync access feature is set to the Disabled mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1926

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Quick Sync interface is enabled.
Detailed Description: The iDRAC Quick Sync interface is enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1927

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Quick Sync access feature is set to the read-only mode.
Detailed Description: The iDRAC Quick Sync access feature is set to the read-only mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1928

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Quick Sync access feature is set to the read-write mode.
Detailed Description: The iDRAC Quick Sync access feature is set to the read-write mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1929

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The iDRAC Quick Sync inactivity timeout value is set to arg1.

Arguments

arg1 = timeout period

Detailed Description

The iDRAC Quick Sync inactivity timeout value is set to the value identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1930

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Quick Sync inactivity timeout feature is enabled.
Detailed Description: The iDRAC Quick Sync feature is set to automatically disable after a specified inactivity time.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1931

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The iDRAC Quick Sync inactivity timeout configuration is disabled.
Detailed Description: The iDRAC Quick Sync inactivity timeout configuration is disabled. The iDRAC Quick Sync feature will remain available after pressing the activate button.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1932

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Sync initiated LED blink configuration change action on arg1.

Arguments

arg1 = device

Detailed Description

Quick Sync initiated LED blink configuration change.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1933

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Sync initiated configuration change on arg1.

Arguments

arg1 = device

Detailed Description

Quick Sync initiated configuration change.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1940

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync Read Authentication feature is enabled.
Detailed Description: The Quick Sync Read Authentication feature is enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1941

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync Read Authentication feature is disabled.
Detailed Description: The Quick Sync Read Authentication feature has been set to Disabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1942

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync Wifi feature is enabled.
Detailed Description: The Quick Sync Wifi feature is enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1943

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync Wifi feature is disabled.
Detailed Description: The Quick Sync Wifi feature has been set to Disabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1944

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync access feature is set to the Disabled mode.
Detailed Description: The Quick Sync access feature is set to the Disabled mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1945

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync interface is enabled.
Detailed Description: The Quick Sync interface is enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1946

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync access feature is set to the read-only mode.
Detailed Description: The Quick Sync access feature is set to the read-only mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1947

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync access feature is set to the read-write mode.
Detailed Description: The Quick Sync access feature is set to the read-write mode.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1948

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Quick Sync inactivity timeout value is set to arg1.

Arguments

arg1 = timeout period

Detailed Description

The Quick Sync inactivity timeout value is set to the value identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1949

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync inactivity timeout feature is enabled.
Detailed Description: The Quick Sync feature is set to automatically disable after a specified inactivity time.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1950

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Quick Sync inactivity timeout configuration is disabled.
Detailed Description: The Quick Sync inactivity timeout configuration is disabled. The iDRAC Quick Sync feature will remain available after pressing the activate/deactivate button.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1951

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The automatic TLS certificate enrollment service is enabled.
Detailed Description: The automatic TLS certificate enrollment service is enabled.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1952

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The automatic Transport Layer Security (TLS) certificate enrollment service is disabled.
Detailed Description: The automatic TLS certificate enrollment service is disabled. The TLS certificate is still in use but not being monitored.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1953

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the certificate-related operation because the Automatic Certificate Enrollment (ACE) feature is enabled.
Detailed Description: The certificate-related operation cannot be completed because the Automatic Certificate Enrollment (ACE) feature is enabled. Example certificate operations are CSR, Upload SSL Certificate, Upload SSL Key, Upload Custom Signing Certificate.
Recommended Response Action: Disable the Automatic Certificate Enrollment (ACE) feature and retry the operation. To disable by using iDRAC Graphical User Interface (GUI), navigate to iDRAC Settings->Services->Web Server->SSL Certificate. For more information about disabling the ACE feature, refer to the iDRAC Users Guide available on the support site.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1954

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The automatic Transport Layer Security (TLS) certificate enrollment service is enrolled. The httpd service is restarting which may end the current GUI session.
Detailed Description: The automatic Transport Layer Security (TLS) certificate enrollment service is enrolled. The service received a signed certificate from Certificate Authority (CA). It is monitoring the expiry date (not-valid-after date) of the certificate.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC1955

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete the operation because the automatic Transport Layer Security (TLS) certificate enrollment service status is: arg1.arg2.

Arguments

arg1 = status
arg2 = CA-error

Detailed Description

The operation cannot be completed because the automatic Transport Layer Security (TLS) certificate enrollment service status identified in the message.

Recommended Response Action

Retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC1956

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Transport Layer Security(TLS) certificate has been updated. The webservices are restarting which may end the current web session.
Detailed Description: The TLS certificate has been manually updated by one of the following methods.1) SSL signing request, 2) Custom Signing Certificate, 3) Custom Certificate, 4) SSL Reset Config. Or, it is automatically updated by the Automatic Certificate Enrollment(ACE) operation. The webservices are now restarted to make the new certificate effective for web sessions.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC3000

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Successfully set arg1 arg2.

Arguments

arg1 = device
arg2 = setting

Detailed Description

Changes to the specified device and specified setting is successful.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Trap/EventID

8483

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC3001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to set arg1 arg2. Code arg3.

Arguments

arg1 = device
arg2 = setting
arg3 = error code

Detailed Description

Changes to the specified device and specified setting is not successful. The cause of the problem is identified by the error code.

Recommended Response Action

Refer to the product documentation on the support site for interpretation of the error code.

Category

Configuration (SWC = Software Config)

Severity

Warning

Trap/EventID

10530

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC4004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A firmware or software incompatibility detected between iDRAC in slot arg1 and CMC/MM.

Arguments

arg1 = number

Detailed Description

FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.

Recommended Response Action

Check firmware versions of iDRAC and CMC/MM. Update to latest version.

Category

System Health (SWC = Software Config)

Severity

Warning

Trap/EventID

2338

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC4005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A firmware or software incompatibility was corrected between iDRAC in slot arg1 and CMC/MM.

Arguments

arg1 = number

Detailed Description

No detailed description available.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Trap/EventID

2339

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC4006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A firmware or software incompatibility detected between system BIOS in slot arg1 and CMC/MM.

Arguments

arg1 = number

Detailed Description

FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.

Recommended Response Action

Check firmware versions of BIOS and CMC/MM. Update to latest version.

Category

System Health (SWC = Software Config)

Severity

Warning

Trap/EventID

2338

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC4007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A firmware or software incompatibility was corrected between system BIOS in slot arg1 and CMC/MM.

Arguments

arg1 = number

Detailed Description

No detailed description available.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Trap/EventID

2339

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC4008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A firmware or software incompatibility detected between CMC/MM 1 and CMC/MM 2.
Detailed Description: FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.
Recommended Response Action: Check firmware versions. Update CMC/MM 1 and CMC/MM 2 firmware to match.
Category: System Health (SWC = Software Config)
Severity: Warning
Trap/EventID: 2338
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC4009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A firmware or software incompatibility was corrected between CMC/MM 1 and CMC/MM 2.
Detailed Description: No detailed description available.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Trap/EventID: 2339
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log
Applicable Event or Alert Types: CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC4010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1arg2 in Server-arg3 requires a version of Chassis Management Controller/Management Module (CMC/MM) firmware 5.0 or later for using the NParEP (ARI mode) functions.

Arguments

arg1 = name
arg2 = location1
arg3 = location2

Detailed Description

The current CMC/MM firmware does not support the ARI Mode advanced features available in the network device on the server identified in the message.

Recommended Response Action

Update the CMC/MM firmware to the latest version and to enable access to the advanced features available in the network device.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC4011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A firmware or software incompatibility is automatically corrected between the arg1arg2 in Server-arg3 and the Chassis Management Controller/Management Module (CMC/MM).

Arguments

arg1 = name
arg2 = location1
arg3 = location2

Detailed Description

A firmware or software incompatibility was automatically corrected between the network device in the Server identified in the message and the Chassis Management Controller/Management Module (CMC/MM).

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC4012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A firmware or software incompatibility is detected between arg1arg2 and arg3arg4.

Arguments

arg1 = name1
arg2 = location1
arg3 = name2
arg4 = location2

Detailed Description

The system has detected a firmware or software incompatibility between the components identified in the message. A mismatch between component versions may cause the system to not function appropriately.

Recommended Response Action

Update the firmware or software of the components identified in the message. For information about the identified components, see the product documentation available at the service provider support site.

Category

System Health (SWC = Software Config)

Severity

Critical

Trap/EventID

2337

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, LC Log*, OS Log, Chassis Event Proxy*

SWC4013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A firmware or software incompatibility was corrected between arg1arg2 and arg3arg4.

Arguments

arg1 = name1
arg2 = location1
arg3 = name2
arg4 = location2

Detailed Description

A firmware or software incompatibility was corrected between the components identified in the message.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Trap/EventID

2339

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, LC Log*, OS Log, Chassis Event Proxy*

SWC4014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to recover the Secure Control Module (SCM) Host Processor Model (HPM) Field Programmable Gate Array (FPGA) version because of arg1.

Arguments

arg1 = Error_Reason

Detailed Description

The FPGA Version Sync feature cannot recover the FPGA because of an internal issue or unable to find a recovery file.

Recommended Response Action

Update the FPGA Dell Update Packages (DUP) using the Open Server Manager UI.

Category

System Health (SWC = Software Config)

Severity

Critical

LCD Message

The FPGA Version is unable to recover the FPGA because of an internal error or unavailable to find a recovery file.

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC4015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Secure Control Module (SCM) Host Processor Model (HPM) Field Programmable Gate Array (FPGA) version mismatch was detected. arg1.

Arguments

arg1 = Auto-recovery_Status

Detailed Description

An FPGA version mismatch was detected because of the reason identified in the message.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

LCD Message

An FPGA version mismatch was detected because of the reason identified in the message.

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC4016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to verify the Secure Control Module (SCM) Host Processor Model (HPM) Field Programmable Gate Array (FPGA) version because of arg1.

Arguments

arg1 = Error_Reason

Detailed Description

The FPGA version cannot be verified because of the reason identified in the message.

Recommended Response Action

Perform an AC Power Cycle operation by doing the following: 1) Disconnect the power cords from the server. 2) Wait 30 seconds. 3) Reconnect the power cords to the server. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Critical

LCD Message

The FPGA Version encountered an internal error and therefore cannot complete the FGPA Version Check.

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5000

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 upgrade was successful.

Arguments

arg1 = name

Detailed Description

No detailed description available.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 upgrade failed.

Arguments

arg1 = name

Detailed Description

No detailed description available.

Recommended Response Action

Reboot the system and attempt the upgrade again.

Category

System Health (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 upgrade was successful but encountered minor errors.

Arguments

arg1 = name

Detailed Description

No detailed description available.

Recommended Response Action

Check system logs for minor errors.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System Controller (SC) has either stopped functioning or is updating a firmware version.
Detailed Description: The System Controller (SC) has either stopped functioning or is updating a firmware version.
Recommended Response Action: Make sure that the System Controller is functioning.
Category: System Health (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System Controller (SC) has restarted functioning.
Detailed Description: System Controller (SC) has started functioning again because either a server health issue is resolved or SC has completed a firmware update process.
Recommended Response Action: No response action required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to update the System Controller (SC) firmware.
Detailed Description: The System Controller (SC) firmware cannot be updated. For information about the causes, see SEL Event Data Byte 2.
Recommended Response Action: Retry the SC firmware update operation. If the issue persists, try updating by using a different firmware update file.
Category: Updates (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System Controller (SC) Firmware Update Successful.
Detailed Description: System Controller (SC) reported a successful Firmware Update.
Recommended Response Action: No response action required.
Category: Updates (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to access arg1 because of a degraded functionality.

Arguments

arg1 = name

Detailed Description

The <name> cannot be accessed because of a degraded functionality.

Recommended Response Action

If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Warning

LCD Message

Unable to access <name> because of a degraded functionality.

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to access arg1 because of a hardware error condition.

Arguments

arg1 = name

Detailed Description

The device identified in the message cannot be accessed because of a hardware error condition.

Recommended Response Action

1) Turn off the server and disconnect input power. 2) Wait for one minute, and then reconnect the power. 3) If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Critical

LCD Message

Unable to access <name> because of a hardware error condition.

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: BIOS image verification failed.
Detailed Description: BIOS image verification failed. The BIOS image file recovery operation is initiated.
Recommended Response Action: No response action is required. For specific issue-related information, see the Lifecycle Log data, and then initiate necessary corrective action.
Category: System Health (SWC = Software Config)
Severity: Critical
LCD Message: BIOS image verification failed.
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: BIOS image recovered.
Detailed Description: The BIOS image file recovery operation completed successfully.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to verify the BIOS image file because: arg1.

Arguments

arg1 = reason

Detailed Description

The BIOS image file cannot be verified because of the reasons identified in the message.

Recommended Response Action

Wait for the system to automatically retry the BIOS recovery process. If the issue persists, attempt a systemcold boot operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to power on the server because an unidentified cable or device is being disconnected. One or more components such as power, signal, and Slimline (SL) cables on the device using SLarg1, may not be fully seated.

Arguments

arg1 = arg

Detailed Description

The system cannot be powered on because the device associated with the SL (slimline PCIe data) cable identified in the message is removed, or missing a required SL cable, power cable, or signal cable. This may be a device seating issue, or a connectivity issue with a cable required by the device.

Recommended Response Action

Do the following:1) There is a cable or connection issue which requires correction. Begin by identifying the issue:1a) Review the Lifecycle Log for any Hardware Configuration (HWC) events that may be reported shortly after this event. If the system can identify the cable or component causing this issue, it will report a configuration error.1b) Reference the System Information Label on the chassis cover or the Cable Routing section in the Installation and Service Manual (ISM). If the HWC message was located, look for references to that connection, cable, or device. Else, use the SL cable referenced in the message to locate the connector on the motherboard.This will be used to trace the cable to the end device.1c) If any maintenance or service work was recently completed and SWC5012 was not present before this activity, something is likely disconnected in that area.2) Proceed with correction:2a) Disconnect the power cords.2b) Use the information gathered above to locate the impacted cable or device. Else, locate the SL cable connector on the motherboard and trace the cable to the end device.2c) Ensure that the device is firmly seated and, if it has any power, signal, and SL cables, ensure they are connected and firmly seated on both ends.2d) Close the chassis cover and reconnect the power cords.2e) If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Critical

LCD Message

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: BIOS image Live Scan verification failed.
Detailed Description: BIOS image verification failed.
Recommended Response Action: No response action is required. For specific issue-related information, see the Lifecycle Log data, and then initiate necessary corrective action.
Category: System Health (SWC = Software Config)
Severity: Critical
LCD Message: BIOS image Live Scan verification failed.
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

BIOS live scan operation failed because: arg1.

Arguments

arg1 = reason

Detailed Description

The BIOS image file cannot be verified because of the reasons identified in the message.

Recommended Response Action

Do one of the following based on failure reason: 1) Integrity check failed - Initiate a BIOS recovery process using Dell supported BIOS image file. 2) Server is powered off or POST not complete - Power ON the server and wait until POST completes and retry the operation. 3) Resource busy or Internal error - Retry the operation at a later point.

Category

System Health (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Chassis firmware update operation failed to start as another update is in progress.
Detailed Description: Chassis firmwareupdate operation failed to start as another update is in progress.
Recommended Response Action: No response action required.
Category: Updates (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to update the firmware of the chassis Power Supply Unit (PSU) because one or more sleds installed on the chassis are currently powered on.
Detailed Description: The firmware of the chassis Power Supply Unit (PSU) cannot be updated because one or more sleds installed on the chassis are currently powered on.
Recommended Response Action: Power off all the sleds in the chassis and then retry the operation. For information about powering off sleds, see the hardware documentation of the chassis available on the support site.
Category: Updates (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5017

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to upgrade the firmware of the chassis Power Supply Unit (PSU) because an incompatible PSU Update Package is used.
Detailed Description: The firmware of the chassis Power Supply Unit (PSU) cannot be upgraded because and incompatible PSU Update Package is used.
Recommended Response Action: Download compatible version of the PSU Update Package from the support site, and then retry the operation. For information about compatible Update Packages, see the iDRAC Users Guide available on the support site.
Category: Updates (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC5018

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to power on the host system because the cable is not connected on PSU/PUCK arg1.

Arguments

arg1 = number

Detailed Description

The host system cannot be powered on because the cable is not connected on PSU/PUCK identified in the message.

Recommended Response Action

Make sure the upstream power cables are connected, and then retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5019

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to authenticate the BIOS image file because: arg1.

Arguments

arg1 = reason

Detailed Description

The BIOS image file cannot be authenticated because of the reasons identified in the message.

Recommended Response Action

Wait for the system to boot. If the issue persists, attempt a system cold boot operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5020

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The arg1 is successfully authenticated.

Arguments

arg1 = deviceName

Detailed Description

The device identified in the message is successfully authenticated.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5021

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Intel Boot Guard failure detected. arg1.

Arguments

arg1 = Reason Code

Detailed Description

Intel Boot Guard failure detected.

Recommended Response Action

Attempt an AC power cycle from iDRAC using racadm or see user guide. If issue persists, attempt a direct update using racadm recover, or redfish update using /redfish/v1/UpdateService/upload HTTP/1.1. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5022

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to verify the BIOS image file because: arg1.

Arguments

arg1 = reason

Detailed Description

The BIOS image file cannot be verified because of the reason identified in the message.

Recommended Response Action

Wait for the system to automatically retry the BIOS recovery process. If the BIOS Recovery failure is observed the in lifecycle log data, attempt a direct update by running the following RACADM command: racadm recover BIOS.Setup.1-1.Else, try running the following Redfish command: /redfish/v1/UpdateService/upload HTTP/1.1. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

System Health (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC5023

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to verify the BIOS image file because of internal issues. An attempt to boot the host is continued. Error Code: arg1.

Arguments

arg1 = code

Detailed Description

The BIOS image file cannot be verified because of the internal issues. However, An attempt to boot the host is continued.

Recommended Response Action

If the Auto Livescan feature is enabled, the next scheduled livescan will validate the BIOS image file.If manual livescan is enabled, reinitiate the livescan. If the issue persists, perform an AC Power Cycle operation.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8500

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to generate Profile with [ arg1 ] settings.

Arguments

arg1 = number of entries

Detailed Description

Unable to communicate with iDRAC.

Recommended Response Action

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8501

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to generate Profile.
Detailed Description: Unable to communicate with iDRAC.
Recommended Response Action: Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8502

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A Profile is successfully generated with [ arg1 ] settings.

Arguments

arg1 = settings count

Detailed Description

A Profile is successfully generated with the number of settings identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8503

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Profile is renamed to arg2

Arguments

arg1 = profile name
arg2 = new profile name

Detailed Description

The Profile identified in the message has been renamed.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8504

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Profile renamed to arg2 and description edited.

Arguments

arg1 = profile name
arg2 = new profile name

Detailed Description

The Profile identified in the message was renamed and the description for the Profile was edited.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8505

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Profile description edited.

Arguments

arg1 = profile name

Detailed Description

The description for the Profile identified in the message was edited.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8506

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Profile deleted.

Arguments

arg1 = profile name

Detailed Description

The Profile identified in the message has been deleted.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8507

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 Profile created.

Arguments

arg1 = profile name

Detailed Description

A new Profile identified in the message has been created.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8508

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to capture Profile from server in slot arg1

Arguments

arg1 = slot number

Detailed Description

Unable to communicate with iDRAC.

Recommended Response Action

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8509

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to apply arg1 Profile to server in slot arg2

Arguments

arg1 = profile name
arg2 = slot number

Detailed Description

Unable to communicate with iDRAC.

Recommended Response Action

Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required. The Lifecycle log in the server identified in the message may have additional information about the inability of the iDRAC to apply Profile settings.

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8510

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to apply arg1 Profile to requested Server(s)

Arguments

arg1 = profile name

Detailed Description

Unable to communicate with the iDRAC of the requested Server.

Recommended Response Action

Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required. The Lifecycle log in the server may have additional information about the inability of the iDRAC to apply Profile settings.

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8511

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

User arg1 was successfully added

Arguments

arg1 = user name

Detailed Description

The user name identified in the message was added successfully.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8512

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to add User arg1: arg2-arg3.

Arguments

arg1 = user name
arg2 = error code
arg3 = error message

Detailed Description

Unable to add user name identified in the message. The reason for this issue is described with the error code in the message.

Recommended Response Action

Correct the error described in the message and retry the operation after a few minutes.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8513

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Successfully deleted User arg1.

Arguments

arg1 = user name

Detailed Description

The user name identified in the message was successfully deleted.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8514

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete User arg1: arg2-arg3

Arguments

arg1 = user name
arg2 = error code
arg3 = error message

Detailed Description

Unable to delete the user name identified in the message.

Recommended Response Action

Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name given is valid. If the issue persists, restart the CMC and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8515

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Successfully modified privileges of User arg1.

Arguments

arg1 = user name

Detailed Description

Successfully modified privileges of User identified in the message.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8516

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to modify privileges of User arg1: arg2-arg3

Arguments

arg1 = user name
arg2 = error code
arg3 = error message

Detailed Description

Unable to modify privileges of the User identified in the message.

Recommended Response Action

Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name given is valid. If the issue persists, restart the CMC and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8517

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Successfully modified password of User arg1.

Arguments

arg1 = user name

Detailed Description

Successfully modified the password for the User identified in the message.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8518

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to modify password of User arg1: arg2-arg3

Arguments

arg1 = user name
arg2 = error code
arg3 = error message

Detailed Description

Unable to modify the password of the User identified in the message.

Recommended Response Action

Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name and password given are valid. If the issue persists, restart the CMC and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8519

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Successfully modified user name from arg1 to arg2.

Arguments

arg1 = original user name
arg2 = new user name

Detailed Description

The user name identified in the message was successfully modified.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8520

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to modify user name from arg1 to arg2: arg3-arg4

Arguments

arg1 = original user name
arg2 = new user name
arg3 = error code
arg4 = error message

Detailed Description

Unable to modify the user name specified in the message.

Recommended Response Action

Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name given is valid. If the issue persists, restart the CMC and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8521

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to modify timeout for session: arg1: arg2-arg3

Arguments

arg1 = SER/TEL/SSH/GUI/RAC/KVM/ERR
arg2 = error code
arg3 = error message

Detailed Description

Unable to modify the timeout for the session.

Recommended Response Action

Make sure: 1) The login credentials for the operation have chassis config administration privilege, 2) The session timeout given is valid. If the issue persists, restart the CMC and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8522

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Chassis Group Leader update of member arg1 configuration successful.

Arguments

arg1 = member id

Detailed Description

Successfully completed a configuration sync with the member identified in the message.

Recommended Response Action

No response action required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8523

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to complete Chassis Group Leader update of member arg1.

Arguments

arg1 = DNS or IP address

Detailed Description

Unable to complete a configuration sync with the member identified in the message.

Recommended Response Action

Check the communications between the Chassis Group Leader and the member. Run the RACADM command "racadm ping <DNS or IP address> " to check the communications. If the communications are not functional, resolve the communications issue. If the communications are functional, remove the member from the group and re-add the member. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Audit (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8524

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to add arg1 to Chassis Group because a member already exists with the same addressing information.

Arguments

arg1 = target

Detailed Description

A Chassis Group member already exists with the same hostname or IP address information as the target identified in the message.

Recommended Response Action

No response action is required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8525

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to add member to Chassis Group. Maximum members supported is arg1.

Arguments

arg1 = maximum number of members

Detailed Description

Unable to add member because the maximum number of Chassis Group members indicated in the message has been reached.

Recommended Response Action

Try removing an existing member and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8526

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete Chassis Group member arg1 (arg2)

Arguments

arg1 = member id
arg2 = DNS or IP address of member

Detailed Description

Unable to delete Chassis Group member identified in the message. Another user may have deleted the member before the operation or the group may have been disbanded.

Recommended Response Action

Make sure the member identified in the message exists as a member of the Chassis Group. Use the CMC web interface to select the lead chassis, select the setup tab, and then select the group administration sub tab and check if the member exists. If the member exists, restart the group leader and retry the operation.

Category

Audit (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8527

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Chassis Management Controller is unable to update the iDRAC user name to "root".
Detailed Description: Chassis Management Controller unable to update the IDRAC root user username as root. This can happen if the communication to the iDRAC from CMC is non-functional or if the username supplied is not valid.
Recommended Response Action: Make sure the user name is valid. If communication with iDRAC is not successful, reset the iDRAC. Retry the operation after a few minutes.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8528

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Chassis Management Controller is unable to update the iDRAC root password.
Detailed Description: The Chassis Management Controller is unable to update the IDRAC "root" user password. This can happen if the communication to the iDRAC from CMC is non-functional or if the password entered is not valid.
Recommended Response Action: Make sure the password is valid. If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8529

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Chassis Management Controller unable to enable the iDRAC root user.
Detailed Description: The Chassis Management Controller is unable to enable the iDRAC root user. This can happen if the communication to the iDRAC from CMC is non-functional or iDRAC is rebooting.
Recommended Response Action: If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8530

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Chassis Management Controller unable to set administrator access to the iDRAC root user.
Detailed Description: The Chassis Management Controller is unable to set the server administrator access to the iDRAC root user. This can happen if the communication to the iDRAC from CMC is non-functional or the iDRAC is rebooting.
Recommended Response Action: If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8531

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Chassis Management Controller unable to set iDRAC administrator role for root user account.
Detailed Description: The Chassis Management Controller is unable to set the administrator role for the iDRAC root user. This can happen if the communication to the iDRAC from CMC is non-functional or iDRAC is rebooting.
Recommended Response Action: If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8532

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Chassis Management Controller is unable to set chassis assigned QuickDeploy IP addresses because the starting IP address cannot accommodate all iDRACs.
Detailed Description: The starting IP address specified cannot accommodate all the servers. The starting iDRAC IPv4 Address specifies the static IPv4 address of the iDRAC located in the first slot. The static IPv4 address of each subsequent iDRAC is calculated as a slot number increment of this IPv4 address.
Recommended Response Action: Make sure there are enough IPv4 addresses for all the iDRACs and then retry the operation.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8533

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete delete all keys operation for service accounts for all slots due to problem saving key file.
Detailed Description: The delete all keys for service accounts for all slots operation did not complete successfully due to problems encountered while saving the key file.
Recommended Response Action: Retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category: Audit (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8534

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: All keys deleted for all slots of service account.
Detailed Description: All keys saved in the Chassis Management Controller for PK SSH Authentication are deleted.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8535

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to add key for slot arg1 of service account, due to problem saving key file.

Arguments

arg1 = slot number

Detailed Description

Public Key (PK) SSH Authentication key file upload did not complete successfully because Chassis Management Controller is unable to access the configuration database.

Recommended Response Action

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8536

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to add key for slot arg1 of service account, due to corrupt key.

Arguments

arg1 = slot number

Detailed Description

The add key operation did not complete successfully for the slot identified in the message due to the key being invalid or corrupt.

Recommended Response Action

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8537

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to add key for slot arg1 of service account, due to the key being too long.

Arguments

arg1 = slot number

Detailed Description

The add key operation did not complete successfully for the slot identified in the message due to the key being too long.

Recommended Response Action

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8538

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete key for slot arg1 of service account, due to problem saving key file.

Arguments

arg1 = slot number

Detailed Description

The Public Key (PK) SSH Authentication key file delete operation did not complete successfully because the Chassis Management Controller is unable to access the configuration database.

Recommended Response Action

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8539

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The key delete operation successfully completed for slot arg1 of service account.

Arguments

arg1 = slot number

Detailed Description

The Public Key (PK) SSH Authentication key file delete operation is successfully completed for the slot identified in the message.

Recommended Response Action

No response action required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8540

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The add key operation successfully completed for slot arg1 of service account.

Arguments

arg1 = slot number

Detailed Description

The Public Key (PK) SSH Authentication key file is successfully uploaded to the Chassis Management Controller.

Recommended Response Action

No response action required.

Category

Audit (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8541

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Profile arg1 is imported.

Arguments

arg1 = profile name

Detailed Description

The Profile identified in the message is imported.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8542

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Profile arg1 is exported.

Arguments

arg1 = profile name

Detailed Description

The Profile identified in the message is exported.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8543

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to perform the Boot Identity profile operation because the server in slot arg1 does not have a Service Tag.

Arguments

arg1 = slot number

Detailed Description

The Boot Identity operation cannot be performed because server in the slot identified in the message does not have a Service Tag.

Recommended Response Action

Set the Service Tag value using the F2 System Setup boot utility. Follow the Server BIOS menu instructions for setting an absent Service Tag or If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8547

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to add some of the Media Access Control (MAC) addresses because the MAC addresses are already present in the MAC address pool of Boot Identity profile operations.
Detailed Description: Some or all of the Media Access Control (MAC) addresses cannot be added to the pool because they are already present in the MAC address pool.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8548

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to delete some of the Media Access Control (MAC) addresses because the MAC addresses are not present in the MAC address pool or used by Boot Identity profile.
Detailed Description: The Media Access Control (MAC) addresses cannot be deleted from the pool because they are not present in the MAC address pool.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8549

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The status of Media Access Control (MAC) address arg1 is not valid for Boot Identity profile operations.

Arguments

arg1 = mac address

Detailed Description

The status of Media Access Control (MAC) address identified in the message is not valid. Possible MAC address status values are unassign, assign and active. The value is "unassigned" if the MAC address is not used in any profile. The value is "assigned" if the MAC address used in a profile. The value is "active" if used in a profile applied to a server. The status must be same for all Virtual MAC addresses if assigned to a profile.

Recommended Response Action

Edit the Virtual MAC Address Pool to correct the MAC address status. Possible MAC address status values are unassign, assign and active. The value is "unassigned" if the MAC address is not used in any profile. The value is "assigned" if the MAC address used in a profile. The value is "active" if used in a profile applied to a server. The status must be same for all Virtual MAC addresses if assigned to a profile.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8550

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to capture the server profile because an insufficient number of unused Media Access Control (MAC) addresses in the Virtual MAC Address Pool.
Detailed Description: An insufficient number of unused MAC addresses are available in the Virtual MAC Address database to capture the requested number of profiles.
Recommended Response Action: Add more MAC addresses to the Virtual MAC Address Pool and retry the capture Boot Identity profile operation. Using the CMC GUI, navigate to the Boot Identity page. More MAC addresses are added using "Add MAC Address" option provided in "Manage Virtual MAC Address Pool" section.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8551

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to apply the boot identity profile because the profile arg1 is already in use by the server in slot arg2.

Arguments

arg1 = profile name
arg2 = slot number

Detailed Description

The boot identity profile cannot be applied because the profile identified in the message is in use by the server in the slot identified in the message.

Recommended Response Action

Clear the boot identity of server identified in the message to apply another profile. Using the CMC GUI, navigate to the Boot Identity page, Boot Identities are cleared using "Clear Identity" option provided "Boot Identity Profiles" tab.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8552

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The server in slot arg1 does not have a profile associated with it.

Arguments

arg1 = slot number

Detailed Description

The server in slot identified in the message does not have a profile associated with it.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8553

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The profile arg1 is not valid.

Arguments

arg1 = profile name

Detailed Description

The profile identified in the message is not valid.

Recommended Response Action

Edit the profile and make sure no XML schema or configuration errors are present and then retry the operation.

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8554

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Virtual MAC Address Pool arg1 is invalid for Boot Identity profile operations.

Arguments

arg1 = MAC Address Pool name

Detailed Description

The Virtual MAC Address Pool identified in the message is not valid. This can occur because the XML syntax is not correct or because of invalid configuration values.

Recommended Response Action

Edit the Virtual MAC Address Pool and correct any XML schema or configuration errors present, and then retry the operation.

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8555

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the Boot Identity profile operation because a Boot Identity operation is already in progress.
Detailed Description: The Boot Identity operation cannot be started because a Boot Identity operation is already in progress.
Recommended Response Action: Wait for the current operation to complete, and then retry. Only one Boot Identity operation can be performed at a time.
Category: Configuration (SWC = Software Config)
Severity: Warning
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8556

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Boot Identity profile arg1 is in use by the server that has the Service Tag arg2.

Arguments

arg1 = profile name
arg2 = service tag

Detailed Description

The Boot Identity profile identified in the message is in use by the server that has the Service Tag identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8557

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to delete the profile arg1 because the profile is in use.

Arguments

arg1 = profile name

Detailed Description

The profile identified in the message cannot be deleted because it is currently in use.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8558

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: No specified MAC addresses were deleted because they were not present in MAC Address Pool of Boot Identity profile operations.
Detailed Description: No specified MAC addresses were deleted because they were not present in MAC Address Pool.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8559

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A new Virtual MAC Address Pool is created with arg1 addresses from arg2 for Boot Identity profile operations.

Arguments

arg1 = address count
arg2 = starting address

Detailed Description

A new Virtual MAC Address Pool is created with the number of addresses identified in the message starting from the MAC address identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8560

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

arg1 New Media Access Control (MAC) addresses are added to the Virtual MAC Address Pool for Boot Identity profile operations.

Arguments

arg1 = address count

Detailed Description

New Media Access Control (MAC) addresses are added to the Virtual MAC Address Pool.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8561

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Some or all or the specified MAC addresses are removed from the Virtual MAC Address Pool of Boot Identity profile operations.
Detailed Description: Some or all or the specified MAC addresses are removed from the Virtual MAC Address Pool. Some MAC addresses could not be removed because they were not present.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8562

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: All of the specified MAC addresses are deactivated from the Virtual MAC Address Pool of Boot Identity profile operations.
Detailed Description: All of the specified MAC addresses are deactivated from the Virtual MAC Address Pool.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC8563

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Boot Identity profile arg1 is cleared from server in slot arg2.

Arguments

arg1 = profile name
arg2 = server slot number

Detailed Description

The Boot Identity profile identified in the message is cleared from the server identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8564

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to clear the Boot Identity profile from the server in slot arg1 because there is no response from the server iDRAC.

Arguments

arg1 = server slot number

Detailed Description

The Boot Identity profile from the server identified in the message cannot be cleared because there is no response from the server iDRAC. A MAC Address conflict is possible if the server retains virtual MAC Address values and they are also allocated to another server.

Recommended Response Action

Make sure that the server is not used until the Persistence Policy settings are returned to default values and the Virtual MAC Address settings have been cleared. Persistence Policy settings can be reset to default values by resetting the server iDRAC to factory default settings. If the iDRAC cannot be reset to default values, if the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution before attempting to use the server.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8565

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Boot Identity profile arg1 is created with arg2 templates.

Arguments

arg1 = profile name
arg2 = number

Detailed Description

The Boot Identity profile identified in the message is created with number of templates as identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8600

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The selected profile was not applied to arg1.

Arguments

arg1 = server list

Detailed Description

The profile version must be compatible with the server generation and Lifecycle Controller firmware version.

Recommended Response Action

Make sure that profile versions are compatible with target servers when attempting application of profiles to servers.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8601

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Deploy Profile unable to apply profile arg1 to server arg2

Arguments

arg1 = profile name
arg2 = server number

Detailed Description

The source profile is not correct in form or content.

Recommended Response Action

Recreate source profile or choose a different one.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8602

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Deploy Profile for server arg1 was not successful.

Arguments

arg1 = server number

Detailed Description

The system is busy with other operations. The feature was unable to get mutex.

Recommended Response Action

Retry the operation. If the issue persists, make sure any other operations have completed and then retry the operation.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8603

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to apply profile to server arg1 using Quick Deploy feature, because the CSIOR feature on Server arg2 is disabled.

Arguments

arg1 = slot number
arg2 = slot number

Detailed Description

The selected profile cannot be applied to the server identified in the message, because the Collect System Inventory On Restart (CSIOR) feature on the server is disabled.

Recommended Response Action

Make sure that CSIOR on the server identified in the messages is enabled and retry the operation. For 11th generation servers, to enable CSIOR, restart the server, and select the Ctrl-E setup. Select System Services, and enable CSIOR. For 12th generation and above, to enable CSIOR using Lifecycle Controller GUI, restart the server, click <F2> when the companys logo is displayed. On the iDRAC Settings page, click Lifecycle Controller, and enable CSIOR.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8604

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Deploy Profile: Server arg1 does not support configuration using profiles.

Arguments

arg1 = server number

Detailed Description

The target server identified in the message does not support server configuration using profiles.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8605

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Deploy Profile: Server arg1 generation information is not recognized.

Arguments

arg1 = server number

Detailed Description

Information about the server identified in the message is not recognized.

Recommended Response Action

Restart the Chassis Management Controller (CMC) and retry the operation. The CMC can be restarted by using the Web UI interface and selecting Chassis Overview > Troubleshooting > Reset Components and then select the Reset/Failover CMC button. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8606

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Deploy Profile: Timeout exceeded while waiting for remote services ready on Server arg1.

Arguments

arg1 = server number

Detailed Description

The server identified in the message never reported that remote services were ready.

Recommended Response Action

Make sure that the iDRAC on the server identified in the message is operating properly and that Lifecycle Controller is enabled, then retry the operation. If the issue persists, perform a virtual reseat of the server and retry the operation. The server can be virtually reseated by using the CMC Web UI interface and selecting Chassis Overview > Troubleshooting > Reset Components and then select Virtual Reseat from the drop down operation for the server identified in the message.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8607

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Deploy Profile: Starting to apply profile arg1 to server arg2.

Arguments

arg1 = profile name
arg2 = server number

Detailed Description

The Quick Deploy of Profile process has started for the server identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8608

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Server Profiles: unable to access server: arg1 for operation [arg2] because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.

Arguments

arg1 = slot number
arg2 = wsman operation

Detailed Description

The CMC was unable to perform the operation described in the message because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.

Recommended Response Action

Make sure that iDRAC on the server identified in the message is operating and that Lifecycle Controller is enabled, and then retry the operation. If the issue persists, perform a virtual reseat of the server and retry the operation. To perform a virtual reseat of the server, on CMC Web interface, select Chassis Overview -> Troubleshooting -> Reset Components. On the Reset Components page, select Virtual Reseat from the drop-down menu for the server identified in the message.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, LC Log*, Chassis Event Proxy*

SWC8609

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Server Profiles: unknown response received from server: arg1 for operation [arg2] because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.

Arguments

arg1 = slot number
arg2 = wsman_operation

Detailed Description

The CMC was unable to perform the operation described in the message because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.

Recommended Response Action

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, LC Log*, Chassis Event Proxy*

SWC8610

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Job ID: arg1. CMC sent all settings of profile arg2 to Server (Service Tag: arg3) in Slot arg4.

Arguments

arg1 = job ID
arg2 = profile name
arg3 = service tag
arg4 = slot number

Detailed Description

All settings of the selected profile were sent to the server identified in the message and the operation is captured in the job identified in the message.

Recommended Response Action

No response action is required.

Category

Configuration (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8611

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Profile "arg1" and Server (Service Tag: arg2 in Slot arg3) are not compatible.

Arguments

arg1 = profile name
arg2 = service tag
arg3 = slot number

Detailed Description

CMC cannot perform the server profile application because the selected profile version and the server identified in the message are not compatible.

Recommended Response Action

Make sure to select the correct version of the profile and/or server, and then retry the operation.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8612

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to fully extract boot device information from profile: arg1.

Arguments

arg1 = profile name

Detailed Description

The profile identified in the message does not contain boot device information in a usable format.

Recommended Response Action

Recreate the profile identified in the message or use a different profile.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8613

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to fully extract arg1 boot list settings from the profile.

Arguments

arg1 = boot list name

Detailed Description

The selected profile does not contain setting information for the boot list identified in the message in a usable format.

Recommended Response Action

Recreate the profile or use a different profile.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8614

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Legacy profile setting: arg1 is not recognized.

Arguments

arg1 = attribute name

Detailed Description

The setting identified in the message is not recognized because the profile is not in a usable format or contains settings that are no longer supported.

Recommended Response Action

Recreate the profile or use a different profile.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8615

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Profile is successfully generated.
Detailed Description: A profile was successfully generated from a server.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Filter Visibility, LC Log*, Chassis Event Proxy*

SWC8616

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Server in slot arg1 is not ready to be accessed remotely because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller for of the server is disabled.

Arguments

arg1 = slot number

Detailed Description

The server identified in the message cannot be accessed remotely by iDRAC because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller for of the server is disabled.

Recommended Response Action

Make sure that the iDRAC on the server identified in the message is operating properly and that Lifecycle Controller is enabled, and then retry the operation. If the issue persists, perform a virtual reseat of the server and retry the operation. The server can be virtually reseated by using the CMC Web GUI interface and selecting Chassis Overview > Troubleshooting > Reset Components and then selecting Virtual Reseat from the drop down menu.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, LC Log*, Chassis Event Proxy*

SWC8617

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Server Profiles: request arg1 for server in slot arg2 was unsuccessful. Returned fault: arg3.

Arguments

arg1 = wsman method
arg2 = slot number
arg3 = wsman fault

Detailed Description

The request by the WS-Man method identified in the message for the server in slot identified slot is unsuccessful.

Recommended Response Action

Make sure that iDRAC is ready and system is functioning properly. Run the RACADM command "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until iDRAC is ready for use. A Virtual Reseat may be required.

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, LC Log*, Chassis Event Proxy*

SWC8618

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Server Profiles: request arg1 for server in slot arg2 was unsuccessful. Message ID arg3. Returned fault: arg4.

Arguments

arg1 = wsman method
arg2 = slot number
arg3 = message id
arg4 = wsman fault

Detailed Description

The request for the WS-Man method identified in the message for server in slot identified slot is unsuccessful.

Recommended Response Action

Make sure that iDRAC is ready and system is functioning correctly. run the RACADM command at the command line interface (CLI), "racadm getversion" to list all the servers and make sure that the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required.

Category

Configuration (SWC = Software Config)

Severity

Critical

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, LC Log*, Chassis Event Proxy*

SWC8619

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Chassis Management Controller is unable to process data from the server in slot arg1.

Arguments

arg1 = slot id

Detailed Description

The Chassis Management Controller (CMC) is unable to process inventory data from the server in the slot identified in the message. This can happen if: 1) There is a communications issue between the CMC and the iDRAC on the server identified in the message. 2) Incorrect firmware is installed on network cards. 3) Incorrect firmware is installed on the server iDRAC. 4) There is no free temporary storage in the CMC.

Recommended Response Action

Do the following and retry the operation: 1) Make sure the latest firmware is installed on the network cards and iDRAC on the server identified in the message. 2) Reset the Chassis Management Controller. 3) Reset the server iDRAC. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC8620

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Chassis Management Controller is unable to communicate with the iDRAC in server slot arg1.

Arguments

arg1 = slot id

Detailed Description

The Chassis Management Controller is unable to communicate with the iDRAC in server slot identified in the message.

Recommended Response Action

Reset the server iDRAC. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC8621

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The Chassis Management Controller is unable to process inventory data from the server in slot arg1.

Arguments

arg1 = slot id

Detailed Description

The Chassis Management Controller (CMC) is unable to process inventory data from the server slot identified in the message. This can happen if there is no free temporary storage in CMC.

Recommended Response Action

Restart the Chassis Management Controller (CMC). To restart the CMC, start an SSH session to the CMC and enter the command "racadm racreset". Wait for the CMC to finish restarting and check if the inventory data is collected. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Filter Visibility, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC8622

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Quick Deploy Profile: Unable to access remote network share and apply assigned profile to the server in slot arg1.

Arguments

arg1 = slot number

Detailed Description

The remote network share settings are accessible on the CMC web interface at Server Overview/Setup/Remote Network Share tab. These settings must be correct for the CMC to connect to the remote network share and perform the application of the profile as specified in the Quick Deploy tab on the Profiles page.

Recommended Response Action

Make sure that the remote network share settings in the CMC are correct and that the remote share NFS/CIFS server is functioning correctly. Use the "Test Network" button in the CMC Web interface to make sure that the CMC can access the remote share.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8623

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to save the I/O Aggregator configuration in arg1.

Arguments

arg1 = slot id

Detailed Description

The current configuration details of IOA in the slot identified in the message could not be saved to its startup configuration.

Recommended Response Action

Power-cycle the IOA and retry the operation.

Category

Configuration (SWC = Software Config)

Severity

Warning

Trap/EventID

10530

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC8624

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The network communication session between CMC and I/O Aggregator cannot be started on arg1.

Arguments

arg1 = slot id

Detailed Description

The network communication session between CMC and I/O Aggregator (IOA) cannot be started because the IOA did not respond.

Recommended Response Action

Power-cycle the IOA and retry the operation.

Category

Configuration (SWC = Software Config)

Severity

Critical

Trap/EventID

10529

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*, OS Log

Applicable Event or Alert Types

CMC—Filter Visibility, SNMP Alert*, Email Alert*, Remote System Log*, LC Log*, Chassis Event Proxy*

SWC8625

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Federal Information Processing Standards (FIPS) mode is enabled on the Chassis.
Detailed Description: The Federal Information Processing Standards (FIPS) mode is enabled on the Chassis.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SWC8626

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Federal Information Processing Standards (FIPS) mode is disabled on the Chassis.
Detailed Description: The Federal Information Processing Standards (FIPS) mode is disabled on the Chassis.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SWC8627

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to configure the storage array in slot arg1, because there is no communication between Chassis Management Controller (CMC) and the storage device.

Arguments

arg1 = slot number

Detailed Description

Unable to configure storage array. This could happen if CMC could not communicate with storage device.

Recommended Response Action

1) Reset iDRAC by using the graphical user interface (GUI): Click Chassis Overview > Troubleshooting > Reset Components. In the Reset Server section, from the Reset drop-down menu, select iDRAC Reset corresponding to the server iDRAC to be reset, and then click Apply Selection. Or, reset iDRAC by running the following command at the command line interface (CLI): racadm racreset -m server-n.2) Reset Chassis Management Controller (CMC) by using the GUI: Click Chassis Overview > Troubleshooting > Reset Components, and then click Reset/Failover CMC. Or, reset CMC by running the following command at the CLI: racadm racreset.For more information about the syntax and parameters used, see the iDRAC 8/7 v2.30.30.30 RACADM CLI Guide and the Chassis Management Controller Version 5.0 for Dell PowerEdge M1000e RACADM Command Line Reference Guide available on the support site.

Category

Configuration (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC8628

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The KVM Access feature is enabled in the chassis.
Detailed Description: The KVM Access feature is enabled in the chassis. To view and operate the OSD screen, connect keyboard and mouse device.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: No alerts are applicable for this message

SWC8629

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The KVM Access feature is disabled in the chassis.
Detailed Description: The KVM Access feature is disabled in the chassis.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: No alerts are applicable for this message

SWC8630

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The KVM feature is inactive because the Chassis Direct feature is active.
Detailed Description: The KVM feature is inactive because the Chassis Direct feature is active.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: No alerts are applicable for this message

SWC8631

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The KVM feature is active because the Chassis Direct feature is inactive.
Detailed Description: The KVM feature is active because the Chassis Direct feature is inactive.
Recommended Response Action: No response action is required.
Category: Audit (SWC = Software Config)
Severity: Informational
Redfish Event Type: Alert
Applicable Event or Alert Types: No alerts are applicable for this message

SWC8632

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to create Profile because the SD card is in Write-protected mode.
Detailed Description: The Profile cannot be created because the Extended Storage removable flash media SD card is not in the Read-Write mode.
Recommended Response Action: Repair the removable flash media SD Card by selecting the Chassis Controller > Flash Media > Configuration > Repair Active Controller Media in the CMC Web interface. Repairing is only allowed on the SD card of the primary CMC. If the problem persists, replace the card. NOTE: All the data on the removable flash media SD card is erased when the feature is disabled.
Category: System Health (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—
Applicable Event or Alert Types: CMC—Filter Visibility, LC Log*

SWC9000

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the SecureBoot Certificate Delete operation either because an invalid thumbprint, hash, certificate type, subtype is entered or due to insufficient space in certificate store.
Detailed Description: The SecureBoot Certificate Delete operation cannot be completed either because an invalid thumbprint, hash, certificate type, subtype is entered or due to insufficient space in certificate store.
Recommended Response Action: Enter correct thumbprint, hash, certificate type, subtype, free some space in the certificate store by deleting few certificates and then retry the operation. For more information, see iDRAC Users Guide available on the support site.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the SecureBoot Certificate DeleteAll operation because of an internal error or insufficient space in certificate store.
Detailed Description: The SecureBoot Certificate DeleteAll operation cannot be completed because of an internal error or insufficient space in certificate store.
Recommended Response Action: Retry the operation. If the issue persists, free some space in the certificate store by deleting few certificates, restart iDRAC, and then retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the SecureBoot Certificate Reset operation either because of insufficient space in certificate store, an internal error or an invalid Certificate type is entered.
Detailed Description: The SecureBoot Certificate Reset operation cannot be completed either because of insufficient space in certificate store, an internal error or an invalid Certificate type is entered.
Recommended Response Action: Enter a valid Certificate type and retry the operation. If the issue persists, free some space in the certificate store by deleting few certificates, restart iDRAC, and then retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the SecureBoot Certificate ResetAll operation because of an internal error or due to insufficient space in certificate store.
Detailed Description: The SecureBoot Certificate ResetAll operation cannot be completed either because of an internal error or due to insufficient space in certificate store.
Recommended Response Action: Retry the operation. If the issue persists, free some space in the certificate store by deleting few certificates, restart iDRAC, and then retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The requested SecureBoot Certificate Import operation cannot be completed.
Detailed Description: The SecureBoot Certificate Import operation cannot be completed because of one or more of the following reasons: corrupted input file (Certificate or UEFI Driver/op-ROM/boot loader file), invalid file, invalid file encoding format, input file (Certificate or UEFI Driver/op-ROM/boot loader file) is not found, the policy that is being updated already exists, insufficient space in certificate store and internal error.
Recommended Response Action: Enter valid parameters and retry the operation. If the issue persists, free some space in the certificate store by deleting few certificates, restart iDRAC, and then retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The requested SecureBoot Certificate Export operation cannot be completed.
Detailed Description: The requested operation was not successful because: 1) Operation is not allowed when SecureBoot policy is Standard. 2) Record not found. 3) Destination not reachable. 4) Destination has insufficient access rights. 5) Internal error.
Recommended Response Action: Make sure that the destination has enough free space, or is not read-only. Retry the operation with valid input parameters. If the problem persists, reboot the iDRAC and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the SecureBoot Certificate View operation because SecureBoot policies are not found in the server.
Detailed Description: The SecureBoot Certificate View operation cannot be completed because SecureBoot policies are not found in the server.
Recommended Response Action: Configure Secureboot policies and retry the operation.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SecureBoot Certificate DeleteAll operation is successfully scheduled. Restart the host server for the changes to take effect.
Detailed Description: The SecureBoot Certificate DeleteAll operation is successfully scheduled.
Recommended Response Action: Restart the host server for the changes to take effect.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SecureBoot Certificate Reset operation is successfully scheduled. Restart the host server for the changes to take effect.
Detailed Description: The SecureBoot Certificate Reset operation is successfully scheduled.
Recommended Response Action: Restart the host server for the changes to take effect.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SecureBoot Certificate ResetAll operation is successfully scheduled. Restart the host server for the changes to take effect.
Detailed Description: The SecureBoot Certificate ResetAll operation is successfully scheduled.
Recommended Response Action: Restart the host server for the changes to take effect.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SecureBoot Certificate Import operation is successfully scheduled. Restart the host server for the changes to take effect.
Detailed Description: The SecureBoot Certificate Import operation is successfully scheduled.
Recommended Response Action: Restart the host server for the changes to take effect.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SecureBoot Certificate Export operation is successfully completed.
Detailed Description: The SecureBoot Certificate Export operation is successfully completed.
Recommended Response Action: No response action is required.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The SecureBoot Certificate Delete operation is successfully scheduled. Restart the host server for the changes to take effect.
Detailed Description: The SecureBoot Certificate Delete operation is successfully scheduled.
Recommended Response Action: Restart the host server for the changes to take effect.
Category: Configuration (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the Secure Boot Certificate Import operation because the file size being imported is greater than the maximum file size allowed for importing.
Detailed Description: The Secure Boot Certificate Import operation cannot be completed because the file size being imported is greater than the maximum file size allowed for importing.
Recommended Response Action: Import the file by using the BIOS System Setup page by pressing F2 when the company logo is displayed while booting the server. For information about the maximum file size allowed, see the iDRAC Users Guide available on the support site.
Category: Configuration (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: System Field Programmable Gate Array (FPGA) or CPLD authentication successful.
Detailed Description: The FPGA or CPLD(s) were authenticated successfully.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to authenticate System Field Programmable Gate Array (FPGA) or CPLD either because of unsuccessful cryptographic authentication or integrity issue.
Detailed Description: System FPGA or CPLD cannot be authenticated either because of unsuccessful cryptographic authentication or integrity issue.
Recommended Response Action: Update the System FPGA or CPLD version either by using UEFI or host Operating System, Lifecycle Controller User Interface, or iDRAC by using the latest Update Package. The host server will be unavailable until the update operation is complete.
Category: System Health (SWC = Software Config)
Severity: Critical
LCD Message: Unable to authenticate System FPGA or CPLD either because of unsuccessful cryptographic authentication or integrity issue.
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to authenticate System Field Programmable Gate Array (FPGA) or CPLD either because of unsuccessful cryptographic authentication or integrity issue.
Detailed Description: System FPGA or CPLD cannot be authenticated either because of unsuccessful cryptographic authentication or integrity issue.
Recommended Response Action: Recover System FPGA or CPLD by using RACADM command in either remote, local, or firmware mode. To recover, run the following RACADM command at the Command Line Interface (CLI): racadm recover CPLD.Embedded.1Alternatively, update the System FPGA or CPLD version either by using UEFI or host Operating System, Lifecycle Controller User Interface, or iDRAC by using the latest Update Package. The host server will be unavailable until the recovery or update operation is complete.
Category: System Health (SWC = Software Config)
Severity: Critical
LCD Message: Unable to authenticate System FPGA or CPLD either because of unsuccessful cryptographic authentication or integrity issue.
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9017

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The Field Programmable Gate Array (FPGA) or CPLD auto-recovery operation has completed successfully.
Detailed Description: One or more System FPGAs or CPLDs could not be authenticated either because of unsuccessful cryptographic authentication or integrity issue. The auto-recovery operation has successfully completed.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9018

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the System Field Programmable Gate Array (FPGA) or CPLD auto-recovery operation because of an internal error.
Detailed Description: One or more System FPGAs or CPLDs could not be authenticated either because of unsuccessful cryptographic authentication or integrity issue. iDRAC was unable to automatically recover them because of an internal error.
Recommended Response Action: Recover System FPGA or CPLD by using RACADM command in either remote, local, or firmware mode. To recover, run the following RACADM command at the Command Line Interface (CLI): racadm recover CPLD.Embedded.1. Alternatively, update the System FPGA or CPLD version either by using UEFI or host Operating System, Lifecycle Controller User Interface, or iDRAC by using the latest Update Package. The host server will be unavailable until the recovery or update operation is complete.
Category: System Health (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9019

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The System Field Programmable Gate Array (FPGA) or CPLD recovery operation has completed successfully.
Detailed Description: The System FPGA or CPLD recovery operation has completed successfully.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9020

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to recover System Field Programmable Gate Array (FPGA) or CPLD because of an internal error.
Detailed Description: iDRAC was unable to complete a System FPGA or CPLD recovery operation requested because of an internal error.
Recommended Response Action: Update the System FPGA or CPLD version either by using the host Operating System, Lifecycle Controller User Interface, or iDRAC by using the latest Update Package. The host server will be unavailable until the update operation is complete and iDRAC will be reset several times.
Category: System Health (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9021

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to authenticate the System Field Programmable Gate Arrays (FPGAs) or CPLD(s) because of an internal error.
Detailed Description: The System FPGA(s) or CPLD(s) cannot be authenticated because of an internal error.
Recommended Response Action: Update System FPGA or CPLD and BIOS to the latest available versions, and then perform a cold-reboot operation on the server. For information about updating the System FPGA or CPLD and BIOS versions, see the Users Guide available on the support site.
Category: System Health (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9022

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A System Field Programmable Gate Array (FPGA) or CPLD recovery operation has been initiated.
Detailed Description: A System FPGA or CPLD recovery operation has been initiated. The host server will be unavailable until the recovery operation is complete and iDRAC will be reset several times.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9023

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The LOM firmware cannot be authenticated either because of unsuccessful cryptographic authentication or integrity issue.
Detailed Description: Unable to authenticate the LOM firmware either because of unsuccessful cryptographic authentication or integrity issue.
Recommended Response Action: Wait for the server to attempt an auto-recovery operation. If the issue persists, update the LOM firmware using the latest Update Package. For information about updating the LOM firmware, see the iDRAC Users Guide available on the Dell support site.
Category: System Health (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9024

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: iDRAC cannot authenticate the LOM firmware because of an internal issue.
Detailed Description: iDRAC cannot authenticate the LOM firmware because of an internal issue.
Recommended Response Action: Update the LOM firmware to the latest available version, and then perform a cold-reboot operation on the server. For information about updating the LOM firmware, see the iDRAC Users Guide available on the Dell support site. If the issue persists, restart iDRAC and retry the operation.
Category: System Health (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9025

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A LOM firmware recovery operation has been initiated.
Detailed Description: iDRAC has initiated an auto LOM firmware recovery operation.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9026

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to recover LOM firmware because of an internal issue.
Detailed Description: iDRAC was unable to complete the LOM firmware recovery operation because of an internal issue.
Recommended Response Action: Update the LOM firmware to the latest Update Package. For information about updating the LOM firmware, see the iDRAC Users Guide available on the Dell support site. If the issue persists, restart iDRAC and retry the operation.
Category: System Health (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9027

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: A new job for recovering the LOM firmware cannot be created because either a job is already scheduled or running.
Detailed Description: Unable to create a new job for recovering the LOM firmware because either a job is already scheduled or running.
Recommended Response Action: Wait for the current recovery job to complete and retry the operation.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9028

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: The LOM firmware authentication operation is not started but skipped because a LOM firmware update or recovery job is either already scheduled or running.
Detailed Description: The LOM firmware authentication operation is not started but skipped because a LOM firmware update or recovery job is either already scheduled or running.
Recommended Response Action: Wait for the recovery job to complete and retry the operation.
Category: System Health (SWC = Software Config)
Severity: Warning
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9029

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to authenticate CPLD either because of unsuccessful cryptographic authentication or integrity issue.
Detailed Description: CPLD cannot be authenticated either because of unsuccessful cryptographic authentication or integrity issue.
Recommended Response Action: Update the CPLD version using the latest Update Package. The host server will be unavailable until the update operation is complete.
Category: System Health (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9030

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to complete the CPLD auto-recovery operation because of an internal error.
Detailed Description: One or more CPLDs could not be authenticated either because of unsuccessful cryptographic authentication or integrity issue. BMC FW was unable to automatically recover them because of an internal error.
Recommended Response Action: Update the CPLD version using the latest Update Package. The host server will be unavailable until the update operation is complete.
Category: System Health (SWC = Software Config)
Severity: Critical
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: No alerts are applicable for this message

SWC9031

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: Unable to start the LOM firmware authentication operation because iDRAC is configured via the LOM port. The authentication operation is skipped.
Detailed Description: The LOM firmware authentication operation is done only in a dedicated mode. To enable the LOM authentication, configure iDRAC via the dedicated port by running the following RACADM command at the RACADM Command Line Interface (CLI): racadm set idrac.nic.Selection Dedicated.
Recommended Response Action: No response action is required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9032

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to verify the BIOS image file because:arg1.

Arguments

arg1 = ROT_Failed_Reason

Detailed Description

The BIOS image file cannot be verified because of the reasons identified in the message.

Recommended Response Action

Contact your service provider to recover.

Category

System Health (SWC = Software Config)

Severity

Critical

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

No alerts are applicable for this message

SWC9033

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message: LOM authentication is skipped because firmware is not programmed on LOM card.
Detailed Description: SMCU firmware is not programmed on the LOM board. Hence LOM firmware authentication can not be done.
Recommended Response Action: No Action required.
Category: System Health (SWC = Software Config)
Severity: Informational
Redfish Event Type: Not Applicable
Applicable Event or Alert Types: iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types: CMC—Not Applicable

SWC9040

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to authenticate the arg1 firmware either because of unsuccessful cryptographic authentication operation or integrity issue.

Arguments

arg1 = ComponentName

Detailed Description

The firmware identified in the message cannot be authenticated either because of unsuccessful cryptographic authentication operation or integrity issue.

Recommended Response Action

1) If the issue is related to LOM or BOSS card associated with iDRAC, then update the LOM or BOSS card firmware using the latest Update Package. 2) If the Floating OCP Paddle (FLOP) card associated with iDRAC has stopped functioning, then to authenticate the FPGA firmware, do the following: 2a) Update the firmware to the latest available version, and then perform an AC Cycle operation on the server. 2b) For information about updating the firmware, see the iDRAC Users Guide available on the Dell support site. If the issue persists, restart iDRAC and retry the operation.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9041

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to authenticate the arg1 firmware because of an internal issue.

Arguments

arg1 = Component Name

Detailed Description

The firmware identified in the message cannot be authenticated because of an internal issue.

Recommended Response Action

1) If the issue is related to LOM or BOSS card associated with iDRAC then perform the Cold Reboot operation on the server. 2) If the issue is related to Floating OCP Paddle (FLOP) card associated with iDRAC then perform a Virtual AC Cycle or AC Cycle operation on the server.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9042

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

The cryptographic authentication of the arg1 firmware is successfully completed.

Arguments

arg1 = ComponentName

Detailed Description

The cryptographic authentication of the component firmware identified in the message is successfully completed.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9043

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A arg1 firmware automatic recovery operation has been initiated.

Arguments

arg1 = ComponentName

Detailed Description

An automatic recovery operation has been initiated on the component identified in the message.

Recommended Response Action

No response action is required.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9044

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to recover the arg1 firmware because of an internal issue.

Arguments

arg1 = ComponentName

Detailed Description

The firmware identified in the message cannot be recovered because of an internal issue.

Recommended Response Action

1) If the issue is related to LOM or BOSS card associated with iDRAC then update the component firmware, and then perform the Cold Reboot operation on the servers. 2) For information about updating the firmware, see the iDRAC Users Guide available on the Dell support site. If the issue persists, restart iDRAC and retry the operation.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9045

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to create a new job for recovering the arg1 firmware because either a job is already scheduled or running.

Arguments

arg1 = ComponentName

Detailed Description

A new job for recovering the firmware cannot be created because either a job is already scheduled or running.

Recommended Response Action

Wait for the current recovery job to complete and retry the operation.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9046

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to start the arg1 firmware authentication operation because a similar firmware update or recovery job is either already scheduled or running.

Arguments

arg1 = ComponentName

Detailed Description

A new job for authenticating the firmware cannot be started because a similar firmware update or recovery job is either already scheduled or running.

Recommended Response Action

Wait for the current recovery job to complete and retry the operation.

Category

System Health (SWC = Software Config)

Severity

Warning

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9047

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

Unable to authenticate the arg1 firmware because firmware is not programmed on the Secure Microcontroller Card (SMCU) card.

Arguments

arg1 = ComponentName

Detailed Description

The component firmware identified in the message cannot be authenticated because firmware is not programmed on the Secure Microcontroller Card (SMCU) card.

Recommended Response Action

Ensure that the required firmware is programmed on the SMCU card and retry the operation.

Category

System Health (SWC = Software Config)

Severity

Informational

Redfish Event Type

Not Applicable

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable

SWC9048

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.

Message

A mismatch between FPGA versions was detected. To ensure proper server operation, update the arg1 FPGA(s).

Arguments

arg1 = cpld_type

Detailed Description

A version mismatch is detected between the Field Programmable Gate Arrays (FPGAs) identified in the message.

Recommended Response Action

Download and install the latest system and peripheral FPGA firmware available on the Dell support site.

Category

Updates (SWC = Software Config)

Severity

Critical

Redfish Event Type

Alert

Applicable Event or Alert Types

iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*

Applicable Event or Alert Types

CMC—Not Applicable