Dell PowerEdge R360 Installation and Service Manual

PDF

Cable routing

6 x 2.5-inch hot-swappable SAS/SATA drives through PERC + 2 x 2.5-inch direct attach NVMe

NOTE:Cable routing image and table is work in progress.
Figure 1. Configuration 0: 4 x 3.5 inch SATA with BOSS N1 (optopnal)
This image shows Cabling diagram of configuration 0 4 x 3.5 inch SATA
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 1. Connector descriptions for 4 x 3.5 inch SATA with BOSS N1 (optional)This table describes the cabling from backplane SAS/SATA and PCIe connector to the connector on the system board and SAS expander card.
Order From To
1 SL1_PCH_SA1 (system board signal connector) BP_DST_SA1 (backplane signal connector)
2 PIB (system board connector) PIB_SIG_1 (PIB signal connector)
3 P1 (system board power connector) SYS (PIB power connector)
4 P2 (system board power connector) CPU (PIB power connector)
5 SIG_PWR_1(PIB power connector) BP_PWR_1 (backplane power connector)
6 CTRL_PNL (system board control panel connector) Right Ear
7 LEFT_LED (system board control panel connector) Left Ear
8 R_INTRUSION (system board intrusion switch connector) Intrusion switch
9 SL2_PCH_PA2 (system board signal connector) J_PCIE_1 (BOSS N1 signal connector)
10 MB_BOSS_PWR (System board power connector) J_PWR_1 (BOSS N1 power connector)
Figure 2. Configuration 1: 4 x 3.5 inch SAS/SATA and fPERC with BOSS N1 (optional)
This image shows Cabling diagram of configuration 1: 4 x 3.5 inch SAS/SATA and fPERC card
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 2. Connector descriptions for 4 x 3.5 inch SAS/SATA and fPERC with BOSS N1 (optional)This table describes the cabling from backplane SAS/SATA and PCIe connector to the connector on the system board and SAS expander card.
Order From To
1 J_SLOT1 (fPERC Riser) CTRL_DST_PA1 (fPERC connector)
2 PIB (system board connector) PIB_SIG_1 (PIB signal connector)
3 P1 (system board power connector) SYS (PIB power connector)
4 P2 (system board power connector) CPU (PIB power connector)
5 SIG_PWR_1(PIB power connector) BP_PWR_1 (backplane power connector)
6 SL2_PCH_PA2 (system board signal connector) J_PCIE_1 (BOSS N1 signal connector)
7 MB_BOSS_PWR (System board power connector) J_PWR_1 (BOSS N1 power connector)
Figure 3. Configuration 2: 4 x 3.5 inch SAS/SATA and internal PERC card
Cabling diagram of configuration 2 4 x 3.5 inch SAS/SATA and internal PERC card
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 3. Connector descriptions for 4 x 3.5 inch SAS/SATA and internal PERC cardThis table describes the cabling from backplane SAS/SATA and PCIe connector to the connector on the system board and SAS expander card.
Order From To
1 CTRL_SRC_SA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
2 PIB (system board connector) PIB_SIG_1 (PIB signal connector)
3 P1 (system board power connector) SYS (PIB power connector)
4 P2 (system board power connector) CPU (PIB power connector)
5 SIG_PWR_1(PIB power connector) BP_PWR_1 (backplane power connector)
Figure 4. Configuration 3: -8 x 2.5 inch SAS/SATA and fPERC card with optional BOSS N1
This images shows cable diagram of Configuration 3: - 8 x 2.5 inch SAS/SATA and fPERC card with optional BOSS N1
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 4. Connector descriptions for 8 x 2.5 inch SAS/SATA and fPERC card with optional BOSS N1This table describes the cabling from backplane SAS/SATA and PCIe connector to the connector on the system board and SAS expander card.
Order From To
1 J_SLOT1 (fPERC Riser) CTRL_DST_PA1 (fPERC connector)
2 PIB (system board connector) PIB_SIG_1 (PIB signal connector)
3 P1 (system board power connector) SYS (PIB power connector)
4 P2 (system board power connector) CPU (PIB power connector)
5 SIG_PWR_1(PIB power connector) BP_PWR_1 (backplane power connector)
6 SL2_PCH_PA2 (system board signal connector) J_PCIE_1 (BOSS N1 signal connector)
7 MB_BOSS_PWR (System board power connector) J_PWR_1 (BOSS N1 power connector)
Figure 5. Configuration 4: - 8 x 2.5 inch SAS/SATA and internal PERC card
Cabling diagram of configuration 4 - 8 x 2.5 inch SAS/SATA and internal PERC card
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 5. Connector descriptions for 8 x 2.5 inch SAS/SATA and internal PERC cardThis table describes the cabling from backplane SAS/SATA and PCIe connector to the connector on the system board and SAS expander card.
Order From To
1 CTRL_SRC_SA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
2 PIB (system board connector) PIB_SIG_1 (PIB signal connector)
3 P1 (system board power connector) SYS (PIB power connector)
4 P2 (system board power connector) CPU (PIB power connector)
5 SIG_PWR_1(PIB power connector) BP_PWR_1 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\