- Notes, cautions, and warnings
- Dell PowerEdge R530 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System cover
- Inside the system
- Cooling shroud
- System memory
- Hard drives
- Removing a hot swappable hard drive or SSD
- Installing a hot-swap hard drive
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Removing a 2.5-inch hot swappable hard drive from a 3.5-inch hard drive adapter
- Installing a 2.5-inch hot swappable hard drive into a 3.5-inch hard drive adapter
- Removing a 3.5-inch hot swappable hard drive adapter from a 3.5-inch hot swappable hard drive carrier
- Installing a 3.5-inch hard drive adapter into the 3.5-inch hot swappable hard drive carrier
- Removing a hard drive from a hard drive carrier
- Installing a hard drive into a hard drive carrier
- Optical drive (optional)
- Cooling fans
- Internal USB memory key (optional)
- Expansion cards and expansion card riser
- Expansion card installation guidelines
- Removing an expansion card from the system board
- Installing an expansion card on the system board
- Removing the optional expansion card riser
- Installing the optional expansion card riser
- Removing an expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- iDRAC port card (optional)
- SD vFlash card (optional)
- Internal dual SD module (optional)
- Integrated storage controller card
- Processors and heat sinks
- Power supply units (PSU)
- Hot spare feature
- Removing the power supply unit blank
- Installing the power supply unit blank
- Removing an AC power supply unit
- Installing an AC power supply unit
- Non-redundant AC power supply unit (cabled)
- Wiring instructions for a DC power supply unit
- Removing a DC power supply unit
- Installing a DC power supply unit
- Power interposer board
- System battery
- Hard drive backplane
- Control panel
- System board
- Trusted Platform Module
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting iDRAC Direct (USB XML configuration)
- Troubleshooting iDRAC Direct (Laptop connection)
- Troubleshooting a serial I/O device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting an SD card
- Troubleshooting an optical drive
- Troubleshooting a tape backup unit
- Troubleshooting a hard drive
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- System messages
- Using system diagnostics
- Jumpers and connectors
- Getting help
Dell PowerEdge R530 Owner's Manual
Entering the iDRAC Settings utility
Steps
- Turn on or restart the managed system.
- Press F2 during Power-on Self-test (POST).
- On the System Setup Main Menu page, click iDRAC Settings.
The iDRAC Settings screen is displayed.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\