Integrated Dell Remote Access Controller 9 Attribute Registry

PDF

InfiniBand Attributes

InfiniBand.VndrConfigPage.LinkStatus (Read Only)

Description: Physical link status of the network port as reported by the controller.
Help Text: Physical link status of the network port as reported by the controller.
Legal Values: Connected;Disconnected
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiGenParams.TcpIpViaDHCP (Read or Write)

Description: Setting to enable acquisition of IPv4 TCP/IP parameters from DHCP
Help Text: This option is specific to IPv4. Controls the source of the initiator IP address, DHCP or static assignment.
Legal Values: Enabled;Disabled
Default Value: Disabled
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.NICConfig.LegacyBootProto (Read or Write)

Description: Selection of the boot protocol for the port to use in legacy BIOS (non-UEFI) boot mode. The default value of the setting varies by implementation and is defined in ENG0012856.
Help Text: Select a boot protocol to be used in legacy BIOS (non-UEFI) boot mode.
Legal Values: PXE;iSCSI;FCoE;None;iSCSI Primary;iSCSI Secondary;iPXE without failover; iSCSI without failover
Default Value: varies
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiGenParams.IscsiViaDHCP (Read or Write)

Description: Setting to enable acquisition of iSCSI target parameters from DHCP.
Help Text: Enables the acquisition of iSCSI target parameters from DHCP.
Legal Values: Enabled;Disabled
Default Value: Disabled
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiGenParams.IscsiTgtBoot (Read or Write)

Description: Controls whether the iSCSI initiator will boot to the specified iSCSI target after connection. One Time Disabled disables iSCSI boot for the next (current) boot, after which it is enabled.
Help Text: Specify whether the iSCSI initiator will boot to the specified iSCSI target after connection. One Time Disabled disables iSCSI boot for the next (current) boot, after which it is enabled.
Legal Values: Enabled;Disabled;One Time Disabled
Default Value: Disabled
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiFirstTgtParams.ConnectFirstTgt (Read or Write)

Description: Setting to enable whether connection to the first target is attempted.Enables or disables connecting to the first iSCSI target. Not available if VndrConfigPage.iSCSIBootSupport is unavailable.
Help Text: Enable connecting to the first iSCSI target.
Legal Values: Enabled;Disabled
Default Value: Disabled
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiGenParams.IpVer (Read or Write)

Description: Setting displays and allows configuration of the IP version used by iSCSI initiator and targets (Initiator only when a seperate target ipver is implemented). If only one IP version is supported, this attribute should be set to that version and be made Read Only.
Help Text: Specify whether IPv4 or IPv6 network addressing will be used for iSCSI initiator and targets (Applies to the Initiator only when a seperate target IP Version is implemented). [Vendor to provide implementation-specific language].
Legal Values: IPv4;IPv6;None
Default Value: IPv4
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.NICConfig.LnkSpeed (Read or Write)

Description: Selector for link speed(s) to be advertised to link partner for boot operations.  Implementations should only include supported link speeds.  Existing implementations may remain unchanged, new implementations should not use those speeds listed as deprecated but use the new speeds that have been added that infer what modulation scheme is in use, NRZ or PAM4.  New implementations should transition to allow multiple speeds to be selected instead of just one in a simple enumeration scheme.
Help Text: Specifies the port link speed to be used when booting the selected protocol.
Legal Values: Auto Negotiated;10 Mbps Half;10 Mbps Full;100 Mbps Half;100 Mbps Full;1 Gbps;10 Gbps;25 Gbps;40 Gbps;50 Gbps (2x25);50 Gbps (1x50);100 Gbps (4x25);100 Gbps (2x50);100 Gbps (1x100);200 Gbps (4x50);200 Gbps (2x100);200 Gbps (1x200)
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.NicMode (Read or Write)

Description: Enable/Disable the NIC personality on the port. This setting is for when operating in non-NPar mode only. Note: This personality type should be specified as the port default if RDMA is not supported or has dependencies on other device modes or settings.
Help Text: Specify use of the port for L2-Ethernet traffic.
Legal Values: Enabled;Disabled
Default Value: Varies
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.DCBXSupport (Read Only)

Description: Indicates whether Data Center Bridging eXchange Protocol (DCBX) is supported.
Help Text: Specify whether Data Center Bridging eXchange Protocol (DCBX) is supported.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

Infiniband.VndrConfigPage.TOESupport (Read Only)

Description: Indicates whether TCP/IP Offload Engine capability is supported
Help Text: Indicates whether TCP/IP Offload Engine capability is supported.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.OnChipThermalSensor (Read Only)

Description: Indicates whether an on-chip thermal sensor is available.
Help Text: Indicates whether an on-chip thermal sensor is available.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.PXEBootSupport (Read Only)

Description: Indicates whether the PXE Boot capability is supported.
Help Text: Indicates whether PXE Boot capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.FCoEOffloadSupport (Read Only)

Description: Indicates whether FCoE is supported.
Help Text: Indicates whether FCoE is supported.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.iSCSIBootSupport (Read Only)

Description: Indicates whether iSCSI Boot is supported.
Help Text: Indicates whether iSCSI Boot is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.FCoEBootSupport (Read Only)

Description: Indicates whether Fibre Channel over Ethernet Boot capability is supported.
Help Text: Indicates whether Fibre Channel over Ethernet Boot capability is supported.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.iSCSIOffloadSupport (Read Only)

Description: Indicates whether the iSCSI Offload capability is supported.
Help Text: Indicates whether the iSCSI Offload capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.FlexAddressing (Read Only)

Description: Indicates whether the Dell FlexAddressing feature is supported.
Help Text: Indicates whether the Dell FlexAddressing feature is supported.
Legal Values: None.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.NWManagementPassThrough (Read Only)

Description: Indicates whether the Network Management Pass Through capability is supported.
Help Text: Indicates whether the Network Management Pass Through capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.EnergyEfficientEthernet (Read Only)

Description: Indicates whether Energy Efficient Ethernet capability is supported.
Help Text: Indicates whether Energy Efficient Ethernet capability is supported.
Legal Values: String value
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.NicPartitioningSupport (Read Only)

Description: Indicates whether the NIC Partitioning capability is supported.
Help Text: Indicates whether NIC Partitioning capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.TXFlowControl (Read Only)

Description: Indicates whether Transmit (TX) Flow Control capability is supported
Help Text: Indicates whether Transmit (TX) Flow Control capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.TXBandwidthControlMinimum (Read Only)

Description: Indicates whether Transmit (TX) Bandwidth Control Minimum capability is supported
Help Text: Indicates whether Transmit (TX) Bandwidth Control Minimum capability is supported.
Legal Values: VndrConfigPage.TXBandwidthControlMinimum
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.RemotePHY (Read Only)

Description: Indicates whether RemotePHY capability is supported.
Help Text: Indicates whether RemotePHY capability is supported.
Legal Values: String value
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.TXBandwidthControlMaximum (Read Only)

Description: Indicates whether Transmit(TX) Bandwidth Control Maximum capability is supported
Help Text: Indicates whether Transmit(TX) Bandwidth Control Maximum capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DeviceLevelConfig.SRIOVSupport (Read Only)

Description: Indicates whether SR-IOV capability is supported
Help Text: Indicates whether SR-IOV capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.RXFlowControl (Read Only)

Description: Indicates whether Receive (RX) Flow control capability is supported.
Help Text: Indicates whether Receive (RX) Flow control capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DCBSettings.CongestionNotification (Read Only)

Description: Indicates whether Congestion Notification capability is supported.
Help Text: Indicates whether Congestion Notification capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.FeatureLicensingSupport (Read Only)

Description: Indicates whether the Dell Feature Licensing capability is supported.
Help Text: Indicates whether Dell Feature Licensing capability is supported.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.OSBMCManagementPassThrough (Read Only)

Description: Indicates whether OS-BMC Management Pass Through capability is supported.
Help Text: Indicates whether OS-BMC Management Pass Through capability is supported.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DeviceLevelConfig.EVBModesSupport (Read Only)

Description: Indicates the type of EVB Modes supported.
Help Text: Indicates the type of EVB Modes supported.
Legal Values: VEB;VEPA;PE;Multi-channel
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DCBSettings.EnhancedTransmissionSelection (Read Only)

Description: Indicates whether Enhanced Transmission Selection capability is supported.
Help Text: Indicates whether Enhanced Transmission Selection capability is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DCBSettings.PriorityFlowControl (Read Only)

Description: Indicates whether the Priority Flow Control capability is supported.
Help Text: No Help information available.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiInitiatorParams.IscsiInitiatorIpAddr (Read or Write)

Description: The iSCSI initiator IP address. Will be either in IPv4 or IPv6 format depending on value of the IpVer attribute.
Help Text: Specify the IP address of the iSCSI initiator.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiInitiatorParams.IscsiInitiatorSubnet (Read or Write)

Description: The iSCSI initiator Subnet Mask for an IPv4 initiator configuration.
Help Text: Specify the IPv4 Subnet Mask of the iSCSI initiator.
Legal Values: String from 7 to 15 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiInitiatorParams.IscsiInitiatorPrimDns (Read or Write)

Description: The iSCSI initiator Primary DNS IP Address. Will be in either IPv4 or IPv6 format depending on the value of the IpVer attribute.
Help Text: Specify the Primary DNS IP address used by the iSCSI initiator.
Legal Values: String from 2 to 39 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiFirstTgtParams.FirstTgtIscsiName (Read or Write)

Description: The iSCSI Qualified Name (IQN) of the first target.
Help Text: Specify the iSCSI Qualified Name (IQN) of the first iSCSI storage target.
Legal Values: String of up to 223 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiInitiatorParams.IscsiInitiatorName (Read or Write)

Description: Setting to represent and set the iSCSI initiator iSCSI Qualified Name (IQN).
Help Text: Specify the initiators iSCSI Qualified Name (IQN).
Legal Values: String of up to 223 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiFirstTgtParams.FirstTgtChapId (Read or Write)

Description: First Target CHAP ID (up to 128 characters in length). If only a single value of CHAP ID supported then it is stored here.
Help Text: Specify the first iSCSI storage target Challenge-Handshake Authentication Protocol (CHAP) ID. [vendor to specify what is allowed].
Legal Values: String of up to 128 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiInitiatorParams.IscsiInitiatorChapId (Read or Write)

Description: Initiator CHAP ID (up to 128 characters in length). If this can be set on a per target basis, then the first target value shall be stored here.
Help Text: Specify the iSCSI initiator Challenge-Handshake Authentication Protocol (CHAP) ID. [Vendor to describe what is allowed].
Legal Values: String of up to 128 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiInitiatorParams.IscsiInitiatorGateway (Read or Write)

Description: iSCSI initiator default Gateway IP address. Will be in either IPv4 or IPv6 format depending on the value of the IpVer attribute.
Help Text: Specify the IP address of the default Gateway used by the iSCSI initiator.
Legal Values: String from 2 to 39 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.BusDeviceFunction (Read Only)

Description: The value of this attribute depends on the state of the NParEP Mode setting. If NParEP Mode is Disabled, the value is the BIOS assigned PCIe Bus:Device:Function identifier. If NParEP Mode is Enabled, the value is the BIOS assigned PCIe Bus:Function identifier.
Help Text: Indicates the PCI Address of the Physical Function assigned to the port.
Legal Values: String of up to 8 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.ChipMdl (Read Only)

Description: This attribute consists of the concatenation of 2 different elements, a vendor-defined silicon marketing name and the silicon revision information as specified in PCI configuration space, separated by space. For example: R720 B0.
Help Text: Specifies the Chip Type.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.DeviceName (Read Only)

Description: Official product name of the device.
Help Text: Official product name of the device.
Legal Values: None
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.PCIDeviceID (Read Only)

Description: PCI Device ID reported by the controller when operating in non-NPar mode only. The value of the attribute is undefined for controllers operating in NPar mode that change their device IDs or support multiple PCI Device IDs at the partition level.
Help Text: PCI Device ID of the controller.
Legal Values: String of up to 4 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiFirstTgtParams.FirstTgtIpAddress (Read or Write)

Description: First iSCSI target IP address. Will be either IPv4 or IPv6 format depending on the value of the FirstTgtIpVer attribute.
Help Text: Specify the IP address of the first iSCSI target.
Legal Values: String of up to 39 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.VirtMacAddr (Read or Write)

Description: Programmatically assignable MAC address. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent MAC address is by writing 0s to the virtual MAC. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s. If supported, the current address value should be readable at all times, irrespective of feature enablement.
Help Text: Programmatically assignable MAC address for port.
Legal Values: String of up to 17 ASCII characters.
Default Value: 00:00:00:00:00:00
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.MacAddr (Read Only)

Description: The Permanent MAC address assigned during manufacturing.
Help Text: Permanent MAC address assigned during manufacturing.
Legal Values: String of up to 17 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiInitiatorParams.IscsiInitiatorChapPwd (Read or Write)

Description: iSCSI initiator CHAP secret (0 or 12 to 16 characters in length). If this can be set on a per target basis, then the value for the first target shall be stored here.
Help Text: Specify the iSCSI initiator Challenge-Handshake Authentication Protocol (CHAP) secret (password). [Vendor to describe what is allowed].
Legal Values: String from 12 to 16 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.NICPartitioningConfig.NumberPCIFunctionsEnabled (Read Only)

Description: The number of PCI Physical Functions currently enabled on this port.
Help Text: The number of PCI Physical Functions currently enabled on this port.
Legal Values: integer values
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.NICPartitioningConfig.NumberPCIFunctionsSupported (Read Only)

Description: The number of PCI Physical Functions supported on this port. This value may change depending on the support and configuration of NParEP.
Help Text: The number of PCI Physical Functions supported on this port. This value may change depending on the support and configuration of NParEP.
Legal Values: Integer values .
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiFirstTgtParams.FirstTgtTcpPort (Read or Write)

Description: TCP Port number of the first iSCSI target.
Help Text: Specify the TCP Port number of the first iSCSI target.
Legal Values: Integer values from 1 to 65535.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.FrmwImgMenu.FamilyVersion (Read Only)

Description: Firmware family version information. Same as what is returned in the PackageVersionName field by the Firmware Management Protocol GetPackageInfo() call.
Help Text: Installed device firmware family version information.
Legal Values: String of up to 11 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.BlnkLeds (Read or Write)

Description: Blink LEDs for a duration of up to 15 seconds. Only valid for adapters with link LEDs.
Help Text: Specify the number of seconds the LEDs on the physical network port should blink to assist with port identification.
Legal Values: Integer values from 0 to 15.
Default Value: 15
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiGenParams.ChapMutualAuth (Read or Write)

Description: Setting to enable mutual CHAP authentication between the iSCSI initiator and target.
Help Text: To use mutual CHAP authentication, specify an initiator secret on the Initiator Parameters page and configure that secret on the target.
Legal Values: Enabled;Disabled
Default Value: Disabled
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiGenParams.ChapAuthEnable (Read or Write)

Description: Setting to enable CHAP Authentication for iSCSI initiator.
Help Text: Enable the ability of the initiator to use CHAP authentication when connecting to the iSCSI target.
Legal Values: Enabled;Disabled
Default Value: Disabled
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiFirstTgtParams.FirstTgtBootLun (Read or Write)

Description: Specifies the first iSCSI target boot LUN.
Help Text: Specify the boot Logical Unit Number (LUN) on the first iSCSI storage target.
Legal Values: Integer values from 0 to 18446744073709551615.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.FrmwImgMenu.EFIVersion (Read Only)

Description: EFI device driver version information.
Help Text: Installed device EFI driver version information.
Legal Values: String value.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.NICConfig.BootStrapType (Read or Write)

Description: Configure the boot strap mechanism used to boot to the OS.
Help Text: Specify the boot strap method used to boot to the operating system.
Legal Values: Auto Detect-0;BBS-1;Int 18h-2;Int 19h-3
Default Value: AutoDetect
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DeviceLevelConfig.VirtualizationMode (Read or Write)

Description: The Virtualization Mode setting for the device. Note: Not all PCI slots in all servers are capable of supporting virtualization features based on ARI and SR-IOV. The implementation shall check the state of the ARI forwarding bit in the immediate upstream PCI ports config space settings (Device Control Register 2, bit 5) to ensure that it is set before before allowing the selection of SR-IOV and NParEP by the user, if not, those selections shall be disallowed.
Help Text: Specify the type of virtualization used by the controller on all ports.
Legal Values: None;NPar;SR-IOV;NPar + SR-IOV;Advanced NPar;Advanced NPar + SR-IOV
Default Value: NONE
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.NICConfig.BannerMessageTimeout (Read or Write)

Description: Timeout in seconds for banner display during POST
Help Text: Specify the number of seconds that the OptionROM banner is displayed during POST.
Legal Values: Integer values from 0 to 14.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.IscsiFirstTgtParams.FirstTgtChapPwd (Read or Write)

Description: First Target CHAP Secret ( 0 or 12 to 16 characters in length). If only a single value of CHAP Secret is supported then it is stored here.
Help Text: Specify the Challenge-Handshake Authentication Protocol secret (CHAP password) of the first iSCSI storage target. [Vendor to specify what is allowed].
Legal Values: String of up to 16 ASCII characters.
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.iSCSIDualIPVersionSupport (Read Only)

Description: Indicates support for simultaneous IPv4 and IPv6 configurations of the iSCSI initiator and iSCSI primary and secondary targets.
Help Text: Indicates support for simultaneous IPv4 and IPv6 configurations of iSCSI initiator and iSCSI primary and secondary targets.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.NICConfig.BootRetryCnt (Read or Write)

Description: Configure the number of retries in case of boot failure.
Help Text: Specify the number of retries to attempt in case of a boot failure.
Legal Values: No Retry;1 Retry;2 Retries;3 Retries;4 Retries;5 Retries;6 Retries;Indefinite Retries
Default Value: NoRetry
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DeviceLevelConfig.NumberVFSupported (Read Only)

Description: The total number of PCI Virtual Functions supported on this port (or device). Whether the number applies to the device as a whole, or to an individual port, is indicated by the value of the Virtual Function Allocation Basis.
Help Text: The number of virtual functions supported on this port (or device) [VENDOR modify appropriately for the implementation].
Legal Values: Integer values from 0 to 256.
Default Value: 0
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DeviceLevelConfig.RDMASupport (Read Only)

Description: Capability indicator for controllers supporting Remote Direct Memory Management (RDMA), the remote memory management capability that allows server to server data movement directly between application memory without any CPU involvement.
Help Text: Indicates whether any RDMA protocol is supported by the controller.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.DeviceLevelConfig.RDMAProtocolSupport (Read Only)

Description: Indicates what RDMA protocol support is enabled by the controller. Implement as ReadOnly and browser suppressed if the controller only supports one type of RDMA; R/W and not browser suppressed if multiple settings are supported and selectable. [Vendor to provide default setting information]
Help Text: Specify what RDMA Protocol is to be used in operation. [Vendor modify as appropriate].
Legal Values: iWARP;RoCE;iWARP + RoCE
Default Value: None
Write Privilege: Not Applicable
License Required: Express License
Dependency: None

InfiniBand.VndrConfigPage.RDMANICModeOnPort (Read or Write)

Description: Enable/Disable the NIC + RDMA personality on the port. This setting is for when operating in non-NPar mode only. Note: This personality type may be specified as the port default if RDMA traffic can be supported irrespective of any other device mode or setting.
Help Text: Specify use of the port for both L2-Ethernet and RDMA traffic. [Vendor may want to customize type of RDMA supported].
Legal Values: Enabled;Disabled
Default Value: Varies
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.DeviceLevelConfig.VFAllocBasis (Read Only)

Description: Defines the domain in which Virtual Functions are allocated; either Port or Device. Note: A device which implements less than 1 PF per physical port must use Device level VF allocation.
Help Text: Defines the domain in which Virtual Functions are allocated.
Legal Values: Port;Device
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.DeviceLevelConfig.VFAllocMult (Read Only)

Description: Defines the multiple (e.g. x1, x4, x8, etc.) in which VFs must be allocated to a PF.
Help Text: [VENDOR provide appropriate help text for the implementation - what is allowed, etc].
Legal Values: Integer values from 1 to 255.
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.DeviceLevelConfig.VFDistribution (Read or Write)

Description: The value is a string of numbers, each seperated by a colon that defines the distribution of VFs to PFs within the domain specified by VFAllocBasis. Each number represents the number of PVI Virtual Functions to be advertised in PCI config space by each partition (PF). The numbers must sum to an amount less than or equal to the NumberVFSupported attribute value. A value appears in the colon separated list for each Physical Function that can potentially be present within the allocation domain, independent of its enablement state. Values in the list from left to right apply to function numbers in the domain from least to greatest.
Help Text: The value is a string of numbers, each seperated by a colon that defines the distribution of VFs to PFs within the domain specified by VFAllocBasis. Each number represents the number of PVI Virtual Functions to be advertised in PCI config space by each partition (PF). The numbers must sum to an amount less than or equal to the NumberVFSupported attribute value. A value appears in the colon separated list for each Physical Function that can potentially be present within the allocation domain, independent of its enablement state. Values in the list from left to right apply to function numbers in the domain from least to greatest.
Legal Values: Integer values.
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.DeviceLevelConfig.PartitionStateInterpretation (Read Only)

Description: Describes how partitioning is implemented and how the PartitionState attribute is used in the controller. A value of Fixed signifies that partition states are locked and that the current values of PartitionState[n] will not change. A value of Variable signifies that PartitionState[n] may/will change values during the course of device operation as a result of user configuration. Implementations that support changes in PartitionState must implement this attribute. The Default value is implementation dependent.
Help Text: Describes how partitioning is implemented and how the PartitionState attribute is used in the controller.
Legal Values: Fixed; Variable
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.NICConfig.PKey (Read or Write)

Description: PKey ID to be used by PXE boot in the InfiniBand environment
Help Text: PKey ID to be used by PXE boot in InfiniBand fabrics.
Legal Values: Integer values.
Default Value: 0
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.VndrConfigPage.SNAPIState (Read Only)

Description: Indicates whether SNAPI functionality is enabled. Note: Implement only if SNAPI support is set to Available
Help Text: Indicates whether SNAPI functionality is enabled
Legal Values: Enabled;Disabled
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.VndrConfigPage.NodeGUID (Read Only)

Description: The Permanent Node GUID assigned during manufacturing.
Help Text: Permanent Node GUID assigned during manufacturing.
Legal Values: String values
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.VndrConfigPage.PortGUID (Read Only)

Description: The Permanent Port GUID assigned during manufacturing.
Help Text: Permanent Port GUID assigned during manufacturing.
Legal Values: String values
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.VndrConfigPage.SNAPI (Read Only)

Description: Indicates the adapter supports SNAPI functionality by either special interfacing to the PCI slot connector or via cabling to another PCI slot.
Help Text: Indicates whether SNAPI functionality is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.VndrConfigPage.NetworkLinkType (Read or Write)

Description: Select the protocol type to be used on a port that supports multiple fabric types. NOTE: Implement ONLY if VPI Mode is supported
Help Text: Select port network protocol (Ethernet/InfiniBand)
Legal Values: Ethernet;InfiniBand
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.VndrConfigPage.VPI (Read Only)

Description: Indicates whether Virtual Protocol Interconnect (VPI) functionality is supported.
Help Text: Indicates whether Virtual Protocol Interconnect (VPI) functionality is supported.
Legal Values: Available;Unavailable
Default Value: None
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None

InfiniBand.VndrConfigPage.VirtNodeGuid (Read or Write)

Description: Programmatically assignable Node GUID address used when only one PF is assigned to the port. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent Node GUID address is by writing 0s to the virtual Node GUID. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0s.
Help Text: Programmatically assignable Node GUID address.
Legal Values: String of up to 19 ASCII characters.
Default Value: 0000:0000:0000:0000
Write Privilege: Not Applicable
License Required: Not Applicable
Dependency: None