- Notes, cautions, and warnings
- Dell PowerEdge T630 server overview
- Converting the system from tower mode to rack mode
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions for converting system from tower to rack
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System feet
- Caster wheels – optional
- System cover
- Inside the system
- Cooling shroud
- Cooling fans
- Cooling-fan assembly (optional)
- System memory
- Flex bays
- Hard drives
- Removing a hot swappable hard drive or solid state drive
- Installing a hot swappable hard drive
- Removing a 2.5-inch hard drive blank
- Installing a 2.5-inch hard drive blank
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter
- Removing a 2.5-inch hard drive from a 3.5-inch hard drive adapter
- Installing a 3.5-inch hard drive adapter into a hot swap hard drive carrier
- Removing a 3.5-inch hot swappable hard drive adapter from a 3.5-inch hot swappable hard drive carrier
- Removing a hard drive or a solid state drive from a hard drive carrier
- Installing a hot swappable hard drive into a hot swappable hard drive carrier
- Optical drives and tape drives
- Internal USB memory key (optional)
- Expansion card holder
- Expansion cards
- GPU card holder (optional)
- GPU cards (optional)
- Internal dual SD module (optional)
- Internal SD card
- Processors and heat sinks
- Power supply unit
- System battery
- Hard drive backplane
- SD vFlash card (optional)
- Control panel assembly
- System board
- Trusted Platform Module
- Power interposer board and power distribution board
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Getting help
Dell PowerEdge T630 Owner's Manual
System Profile Settings details
About this task
- Option
- Description
- System Profile
- Sets the system profile. If you set the System Profile option to a
mode other than Custom, the BIOS automatically
sets the rest of the options. You can only change the rest of the
options if the mode is set to Custom. This option is set to Performance Per Watt Optimized (DAPC) by default. DAPC is Dell Active Power Controller.NOTE: All the parameters on the system profile setting screen are available only when the System Profile option is set to Custom.
- CPU Power Management
- Sets the CPU power management. This option is set to System DBPM (DAPC) by default.
- Memory Frequency
- Sets the speed of the memory. You can select Maximum Performance, Maximum Reliability, or a specific speed.
- Turbo Boost
- Enables or disables the processor to operate in the turbo boost mode. This option is set to Enabled by default.
- Energy Efficient Turbo
- Enables or disables the Energy Efficient
Turbo option.
Energy Efficient Turbo (EET) is a mode of operation where a processor’s core frequency is adjusted to be within the turbo range based on workload.
- C1E
- Enables or disables the processor to switch to a minimum performance state when it is idle. This option is set to Enabled by default.
- C States
- Enables or disables the processor to operate in all available power states. This option is set to Enabled by default.
- Collaborative CPU Performance Control
- Enables or disables the CPU power management option. When set to Enabled, the CPU power management is controlled by the OS DBPM and the System DBPM (DAPC). This option is set to Disabled by default.
- Memory Patrol Scrub
- Sets the memory patrol scrub frequency. This option is set to Standard by default.
- Memory Refresh Rate
- Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.
- Uncore Frequency
- Enables you to select the Processor Uncore
Frequency option.
Dynamic mode enables the processor to optimize power resources across the cores and uncore during runtime. The optimization of the uncore frequency to either save power or optimize performance is influenced by the setting of the Energy Efficiency Policy option.
- Energy Efficient Policy
- Enables you to select the Energy Efficient
Policy option.
The CPU uses the setting to manipulate the internal behavior of the processor and determines whether to target higher performance or better power savings.
- Number of Turbo Boot Enabled Cores for Processor 1
- NOTE: If there are two processors installed in the system, you see an entry for Number of Turbo Boost Enabled Cores for Processor 2.Controls the number of turbo boost enabled cores for processor 1. The maximum number of cores is enabled by default.
- Monitor/Mwait
- Enables the Monitor/Mwait instructions in the processor.
This option is set to Enabled for all system
profiles, except Custom by default.NOTE: This option can be disabled only if the C States option in the Custom mode is set to disabled.NOTE: When C States is set to Enabled in the Custom mode, changing the Monitor/Mwait setting does not impact the system power or performance.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\