PowerEdge Servers Error and Event Messages Reference Guide

PDF

JCP—Job Control Event Messages

JCP000

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
A new job with ID arg1 is created.
Arguments
  • arg1 = ID number
Detailed Description
A new job with the ID identified in the message is created.
Recommended Response Action
No response action is required.
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP001

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Task successfully scheduled.
Detailed Description
The UEFI automated task related to the job was successfully scheduled.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP002

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to schedule the job.
Detailed Description
The Lifecycle Controller is not able to schedule a job at this time because of an internal error.
Recommended Response Action
Wait up to three minutes and retry the operation. If the problem persists, reboot the system and enumerate DCIM_Lifeycle Job to view the list of jobs that are currently scheduled.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP003

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The Job did not complete successfully.
Detailed Description
The Job did not complete successfully.
Recommended Response Action
Retry the operation, and if necessary, make sure that valid parameters are provided for the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP004

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Time elapsed - Job Failed.
Detailed Description
The jobs time window expired and the job failed to complete.
Recommended Response Action
Retry the action and increase the time window so that the job can complete.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP005

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
System services cancelled - Job Failed
Detailed Description
System services was cancelled by selecting CTRL+E or F2 on boot up and cancelling it through the iDRAC configuration utility. This prevents jobs from executing further.
Recommended Response Action
For 11G systems: Use the iDRAC configuration utility to enable the System Services by pressing on the CTRL+E option on boot up at the targeted system. For 12G and above generations: Use F2 Setup, select iDRAC Configuration, and select Lifecycle Controller Settings, to enable the Lifecycle Controller on boot up of the targeted system.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP006

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Invalid job attribute.
Detailed Description
One or more of the specified values for creating a job are invalid or an internal error has occurred when scheduling the job.
Recommended Response Action
Use the correct value for the job attribute and retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP007

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job successfully completed.
Detailed Description
The submitted job completed successfully.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP008

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job completed with errors.
Detailed Description
Multiple attributes were set in the operation but some set attribute actions were not successful. For example, setting an attribute that is not valid for the component being configured.
Recommended Response Action
Examine the results of the configuration job in the Lifecycle Log for the source of the errors. Modify the settings as necessary and resubmit the job.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP009

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Scheduled job was cancelled.
Detailed Description
Scheduled jobs were deleted as a result of a cancel job request. The job cancellation request is manually or programmatically initiated. Lifecycle Controller enters Recovery mode when unrecoverable and persistent errors occur.
Recommended Response Action
If the job was not cancelled manually, then Lifecycle Controller may be in Recovery mode. To verify or change Recovery mode, use F2 Setup to select iDRAC Configuration then Lifecycle Controller Settings.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP010

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The command was successful.
Detailed Description
The method invoked was successfully completed.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP011

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Invalid parameter value for arg1.
Arguments
  • arg1 = parameter
Detailed Description
The value provided for the specified parameter is invalid and must be corrected for the invoked method to complete successfully.
Recommended Response Action
To provide the correct value for the specified parameter, see Lifecycle Controller-Remote Services documentation. Retry the operation requested with corrected value.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP012

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The operation failed due to an internal iDRAC error.
Detailed Description
The requested operation requires memory or file space allocation. The operation failed due to lack of memory or file space in the iDRAC.
Recommended Response Action
Retry the operation. If the issue persists, reset iDRAC and retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Critical
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP013

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Missing parameter(s) arg1
Arguments
  • arg1 = parameters
Detailed Description
One or more required input parameters needed for the operation are missing.
Recommended Response Action
Refer to the documentation for the operation being attempted and provide valid values for the identified parameters.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP014

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Maximum jobs per queue exceeded.
Detailed Description
The number of jobs specified in the SetupJobQueue request combined with the existing job count contains more jobs IDs than the maximum number of jobs supported by the system (256). Completed jobs are automatically deleted if they are older than the delete on completion timeout setting.
Recommended Response Action
Reduce the number of jobs specified in the operation or reduce the existing job count before retrying the operation. Perform one of the following to reduce the job count: 1) Delete one or more jobs and retry the operation. 2) Wait until existing jobs have an elapsed time since completion that is greater than the delete on completion timeout setting and are automatically deleted. 3) Change the delete on completion timeout setting to a smaller value so that completed jobs are automatically deleted sooner.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP015

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
A running job cannot be deleted.
Detailed Description
The job is currently executing and cannot be deleted. The job needs to finish running, whether successful or not, before it can be deleted.
Recommended Response Action
Wait for the job to have a completed job status. Retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP016

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Invalid UntilTime value. A minimum of 5 minutes is required.
Detailed Description
The UntilTime input parameter for the job or job queue creation must be at least 5 minutes after the value specified in the StartTime parameter.
Recommended Response Action
Set the UntilTime at least 5 minutes after StartTime and retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP017

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create the job because the maximum number of jobs are already created.
Detailed Description
The job cannot be created because the maximum number of jobs are already created.
Recommended Response Action
Reduce the number of current jobs by doing one of the following:1) Manually delete one or more existing jobs and retry the operation.2) Wait for existing jobs to be automatically deleted after their elapsed time because completion exceeds the configured DeleteOnCompletionTimeout value.3) Adjust the DeleteOnCompletionTimeout setting to a smaller value to enable earlier automatic deletion of completed jobs. Use Redfish action DellJobService.SetDeleteOnCompletionTimeout.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP018

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Cannot create new jobs until the existing Export job is completed or the job is cancelled.
Detailed Description
A new job cannot be created until the existing Export job is completed or the job is deleted. There can only be one Export Server Profile job running at a time.
Recommended Response Action
Do one of the following: 1) Retry the operation after the Export Server Profile job is completed. 2) Delete the scheduled Export job and retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP019

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Cannot create new jobs until the existing Import System Profile job is completed or cancelled.
Detailed Description
A new job cannot be created until the existing Import Server Profile job is complete or deleted. Only one Import Server Profile job can be running at any given time.
Recommended Response Action
Do one of the following: 1) Retry the operation after the Import Server Profile job is complete. 2) Delete the scheduled Import Server Profile job and retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP020

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Cannot schedule jobs while export or import operations are running.
Detailed Description
Existing jobs cannot be scheduled while an Export Server Profile or Import Server Profile job is running.
Recommended Response Action
Retry the job scheduling operation after the export or import operation is completed.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP021

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The operation failed due to an internal iDRAC error.
Detailed Description
The operation did not complete successfully because of lack of an unknown error in the iDRAC.
Recommended Response Action
Retry the operation. If the issue persists, reset the iDRAC.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP022

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Invalid Job ID arg1 for scheduling or deletion operation.
Arguments
  • arg1 = jobid number
Detailed Description
An invalid Job ID was provided as input for a scheduling or deletion operation. The Job ID indicated in the message does not match an existing Job on the target system.
Recommended Response Action
Verify the job ID value by enumerating job instances and validating that the Job ID value is correct for the job being scheduled or deleted. Retry the operation with the correct Job ID value.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP023

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Duplicate Job ID arg1.
Arguments
  • arg1 = jobid number
Detailed Description
One of the job ID values specified as input to the operation is a duplicate. The duplicated Job ID is indicated in the message.
Recommended Response Action
Use the correct job ID and retry. Use the GetAllJobs method to retrieve all open jobs.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP024

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Lifecycle Controller is in use. This job starts when Lifecycle Controller is available.
Detailed Description
Lifecycle Controller cannot gain access to internal storage due to use by another application or operation. This job starts when Lifecycle Controller is available.
Recommended Response Action
Wait for current Lifecycle Controller operation to complete. Verify that the system is: 1) Not currently in Lifecycle Controller Unified Server Configurator 2) Not waiting for user intervention at F1/F2 POST error 3) Not in any of the device or controller Option ROMs.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP025

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Lifecycle Controller is not enabled.
Detailed Description
Lifecycle Controller must be enabled to perform the requested operation. Lifecycle Controller can be enabled in the F2 Setup application or through a remote operation.
Recommended Response Action
If Lifecycle Controller is in Recovery mode a firmware update of Lifecycle Controller may be required. To change the Lifecycle Controller mode, do the following: 1) Restart the system and press F2 to launch the System Setup application 2) Select iDRAC Configuration 3) Select Lifecycle Controller Settings to enable Lifecycle Controller.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP026

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Update packages are being downloaded. This job resumes when the downloads are completed.
Detailed Description
Update packages are being downloaded for other jobs initiated on this system. This job resumes when the downloads complete.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP027

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The (installation or configuration) job arg1 is successfully created on iDRAC.
Arguments
  • arg1 = job ID
Detailed Description
The (installation or configuration) job identified in the message is successfully created on iDRAC.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Trap/EventID
10267
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP028

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job status updated.
Detailed Description
An install or configuration job status is successfully updated on iDRAC.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Trap/EventID
10267
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*
Applicable Event or Alert Types
CMC—Not Applicable

JCP029

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
A Job of JobType arg1 already exists.
Arguments
  • arg1 = parameter
Detailed Description
Only one Job of the JobType requested can be created or scheduled at any time. A job of the same type already exists in the job queue.
Recommended Response Action
Wait until the existing job is complete or delete the existing job and then retry the operation.
Category
Audit (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP030

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to schedule jobs while an iDRAC firmware update or configuration job is running.
Detailed Description
Unable to schedule jobs for execution while an iDRAC firmware update job is running.
Recommended Response Action
Wait for the running job to complete, and then retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP031

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to delete the job because the configuration is still being committed.
Detailed Description
The job ID specified as input to the operation has configuration data that is currently being processed by the iDRAC. The job can be deleted after the processing is done.
Recommended Response Action
Retry the operation. If the issue persists, reset the iDRAC by pressing the System ID button for 15 seconds, wait for the iDRAC to finish restarting, and then retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP032

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create a job because conflicting options are entered.
Detailed Description
The configuration job cannot be created because the -r and --realtime options cannot be used at the same time.
Recommended Response Action
Make sure that only one of either -r or --realtime option is entered. For example, to run a job immediately, enter the --realtime option. To schedule a job that will be run after restarting a server, use the -r option. For more information about options, see the RACADM Command Line Reference Guide available at the support site.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP033

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
New job.
Detailed Description
This job is newly created. This is the default message in a job when it has just been created.
Recommended Response Action
No response action is required.
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP034

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
arg1 job is successfully created on iDRAC with arg2.
Arguments
  • arg1 = Job Name
  • arg2 = Job ID
Detailed Description
A new configuration or update job has been created.
Recommended Response Action
No response action is required.
Category
Audit (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP035

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create new jobs because a backup job is currently running.
Detailed Description
New jobs cannot be created because a backup job is already running.
Recommended Response Action
1) Wait for the currently running job to complete and retry the operation. 2) To view running jobs, do one of the following: 2a) At the RACADM CLI, run the "racadm jobqueue view" command. 2) On the Redfish interface, perform a GET operation on "/redfish/v1/JobService/Jobs".
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP036

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The job arg1 is successfully deleted.
Arguments
  • arg1 = job ID
Detailed Description
The job identified in the message is successfully deleted on iDRAC.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP037

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The (installation or configuration) job arg1 is successfully completed.
Arguments
  • arg1 = job ID
Detailed Description
The (installation or configuration) job identified in the message is successfully completed on iDRAC.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Trap/EventID
10267
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP038

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to run the (installation or configuration) job arg1 because arg2.
Arguments
  • arg1 = job ID
  • arg2 = reason
Detailed Description
The (installation or configuration) job identified in the message cannot be run. For more information, see the Job Queue.
Recommended Response Action
Navigate to the Maintenance->overview->Lifecycle Log page in the iDRAC GUI. Look for logs with the prefix "RED" within the timeframe. Perform the recommended response action for these messages by referring to the error message guide.
Category
Configuration (JCP = Job Control)
Severity
Informational
Trap/EventID
10267
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, SNMP Alert, Email Alert, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP040

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
User arg1 via IP arg2 created configuration / update Job ID arg3 with Job Name arg4 using arg5.
Arguments
  • arg1 = user name
  • arg2 = IPv4/6 address
  • arg3 = Job ID
  • arg4 = Job Name
  • arg5 = Interface Type
Detailed Description
User created configuration / update Job with specified Job Name using specified interface.
Recommended Response Action
No response action is required.
Category
Audit (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP041

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to successfully run the job because the System Lockdown mode is enabled.
Detailed Description
The job cannot be run because the System Lockdown mode is enabled.
Recommended Response Action
Disable the System Lockdown mode and retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Alert
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, WS Eventing, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP042

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job arg1 failed because arg2.
Arguments
  • arg1 = job ID
  • arg2 = reason
Detailed Description
The (installation or configuration) job identified in the message cannot be run. For more information, see the Job Queue.
Recommended Response Action
Review the LC Log for related update, configuration, or collection job errors. Retry the operation. If the issue persists, Collect a SupportAssist collection (TSR) report using iDRAC. Visit https://www.dell.com/support/incidents-online/contactus/dynamic to use the Virtual Assistant to analyze the collection and recommend a resolution.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP043

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to start the update operation because the Export or Server Profile Import operation is already in progress.
Detailed Description
The update operation cannot be started because the Export or Server Profile Import operation is already in progress.
Recommended Response Action
Wait for the Export or Server Profile Import operation to complete, and then retry the operation.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP044

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create new jobs until the current iDRAC job downloading operation is either completed or deleted.
Detailed Description
The new jobs cannot be created until the current iDRAC job downloading operation is either completed or deleted. Only one Import Server Profile job can be run at a given time.
Recommended Response Action
Do one of the following and retry the operation: 1) Wait for the current iDRAC job download operation to complete. 2) Delete the scheduled iDRAC download job.
Category
Configuration (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP045

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
All jobs in the Job Queue were deleted successfully.
Detailed Description
All the jobs in Job Queue were deleted successfully.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP046

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
All jobs in the Job Queue were force deleted successfully.
Detailed Description
All the jobs in Job Queue were force deleted successfully.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP047

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create a job because a critical iDRAC job is currently running.
Detailed Description
A new job cannot be created because a critical iDRAC job is currently running.
Recommended Response Action
Wait for the critical iDRAC to be completed and retry the operation.
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP048

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Unable to create a job because the iDRAC firmware is currently getting updated on the server.
Detailed Description
A new job cannot be created because the iDRAC firmware is currently getting updated on the server.
Recommended Response Action
Wait for the iDRAC firmware update process to be completed and retry the operation.
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP049

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The Job arg1 is scheduled to run between arg2 and arg3.
Arguments
  • arg1 = JobID
  • arg2 = start time
  • arg3 = until time
Detailed Description
The Update/Config job is successfully scheduled to run between the Start Time and Until Time specified by user.
Recommended Response Action
No response action is required.
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP050

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The reboot job arg1 is scheduled to run on arg2.
Arguments
  • arg1 = JobID
  • arg2 = date time
Detailed Description
The reboot job is scheduled to run on user specified time.
Recommended Response Action
No response action is required.
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP051

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The Job arg1 is scheduled to run after arg2.
Arguments
  • arg1 = JobID
  • arg2 = start time
Detailed Description
The update of configuration job is successfully scheduled to run after the specified start time.
Recommended Response Action
No response action is required.
Category
Updates (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP052

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The Job was in either running or downloading state and timed out before completion.
Detailed Description
The job failed because it was in either running or downloading state and made no progress for the allocated time. The job was timed out before completion.
Recommended Response Action
Retry the operation.
Category
Updates (JCP = Job Control)
Severity
Warning
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP053

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
The system is in critical condition and a shutdown operation has to be initiated. The system cannot process any new jobs at this stage.
Detailed Description
The system is in critical condition and a shutdown operation has to be initiated. The system cannot process any new jobs at this stage.
Recommended Response Action
No response action is required.
Category
System Health (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

JCP8501

NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the Applicable Event or Alert Types section.
Message
Job ID: arg1. CMC sent arg2 properties from arg3 profile to the server (Service Tag: arg4 ) in the slot arg5.
Arguments
  • arg1 = job ID
  • arg2 = number of settings
  • arg3 = profile name
  • arg4 = service tag
  • arg5 = slot number
Detailed Description
This job information message occurs if some configuration stored in the profile are not applicable to the target server.
Recommended Response Action
No response action is required.
Category
Configuration (JCP = Job Control)
Severity
Informational
Redfish Event Type
Not Applicable
Applicable Event or Alert Types
iDRAC—Filter Visibility, Remote System Log, Redfish Eventing*, LC Log*
Applicable Event or Alert Types
CMC—Not Applicable

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\