PowerEdge Servers Error and Event Messages Reference Guide
SDS—Software Defined Storage Event Messages
SDS0001
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0002
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0003
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Add more drives to the storage pool.
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0004
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0005
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0006
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0007
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0008
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0009
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0010
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a warning.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Warning
- Trap/EventID
- 4762
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0011
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Add more physical drives to the storage pool and retry the operation.
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0012
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = xml-message
- Detailed Description
- The Software Defined Storage subsystem on the host Operating System has reported a failure.
- Recommended Response Action
- Verify the health status of the hard drive identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0021
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = XML-message
- Detailed Description
- The Windows Storage Stack on the host operating system has reported a failure on a Plug n Play(PnP) device.
- Recommended Response Action
- Verify the health status of the device identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
SDS0022
NOTE: Event or Alert types that are enabled by default are identified using an asterisk (*) symbol in the
Applicable Event or Alert Types section.
- Message
- arg1.
- Arguments
- arg1 = XML-message
- Detailed Description
- The Windows Storage Stack on the host operating system has reported a failure on a Plug n Play(PnP) device.
- Recommended Response Action
- Verify the health status of the device identified in the message and retry the operation. To check the health status by using the iDRAC GUI, on the iDRAC dashboard, click Storage > Physical Disks. To run a RACADM command, enter "racadm raid get pdisks -o -p status" at the Command Line Interface (CLI).
- Category
- Storage (SDS = Software Defined Storage)
- Severity
- Critical
- Trap/EventID
- 4761
- Redfish Event Type
- Alert
- Applicable Event or Alert Types
- iDRAC—Filter Visibility, SNMP Alert, Remote System Log, Redfish Eventing*, LC Log*
- Applicable Event or Alert Types
- CMC—Not Applicable
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\