Dell Storage Center SCv2000 and SCv2020 Storage System Getting Started Guide

Worksheet to Record System Information

Use the following worksheet to record the information that is needed to install the SCv2000/SCv2020 storage system .

Storage Center Information

Gather and record the following information about the Storage Center network and the administrator user.

Table 1. Storage Center Network
Service Tag ________________
Management IPv4 address ( Storage Center management address) ___ . ___ . ___ . ___
Top Controller IPv4 address (Controller 1 MGMT port) ___ . ___ . ___ . ___
Bottom Controller IPv4 address (Controller 2 MGMT port) ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
Domain name ________________
DNS server address ___ . ___ . ___ . ___
Secondary DNS server address ___ . ___ . ___ . ___
Table 2. Storage Center Administrator
Password for the default Storage Center “Admin” user ________________
Email address of the default Storage Center “Admin” user ________________

iSCSI Fault Domain Information

For a storage system with iSCSI front-end ports, gather and record network information for the iSCSI fault domains. This information is needed to complete the Discover and Configure Uninitialized SCv2000 Series Storage Centers wizard.

  • NOTE: For a storage system deployed with two Ethernet switches, Dell recommends setting up each fault domain on separate subnets.

See the Dell Storage Center SCv2000/SCv2020 Storage System Deployment Guide for information about setting up iSCSI fault domains.

Table 3. iSCSI Fault Domain 1
Target IPv4 address ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
IPv4 address for storage controller module 1: port 1 ___ . ___ . ___ . ___
IPv4 address for storage controller module 2: port 1 ___ . ___ . ___ . ___
(Four port I/O card only) IPv4 address for storage controller module 1: port 3 ___ . ___ . ___ . ___
(Four port I/O card only) IPv4 address for storage controller module 2: port 3 ___ . ___ . ___ . ___
Table 4. iSCSI Fault Domain 2
Target IPv4 address ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
IPv4 address for storage controller module 1: port 2 ___ . ___ . ___ . ___
IPv4 address for storage controller module 2: port 2 ___ . ___ . ___ . ___
(4-port I/O card only) IPv4 address for storage controller module 1: port 4 ___ . ___ . ___ . ___
(4-port I/O card only) IPv4 address for storage controller module 2: port 4 ___ . ___ . ___ . ___

Additional Storage Center Information

The Network Time Protocol (NTP) and Simple Mail Transfer Protocol (SMTP) server information is optional. The proxy server information is also optional, but it may be required to complete the Discover and Configure Uninitialized SCv2000 Series Storage Centers wizard.

Table 5. NTP, SMTP, and Proxy Servers
NTP server IPv4 address ___ . ___ . ___ . ___
SMTP server IPv4 address ___ . ___ . ___ . ___
Backup SMTP server IPv4 address ___ . ___ . ___ . ___
SMTP server login ID ________________
SMTP server password ________________
Proxy server IPv4 address ___ . ___ . ___ . ___

Fibre Channel Zoning Information

For a storage system with Fibre Channel front-end ports, record the physical and virtual WWNs of the Fibre Channel ports in Fault Domain 1 and Fault Domain 2. This information is displayed on the Review Front-End page of the Discover and Configure Uninitialized SCv2000 Series Storage Centers wizard. Use this information to configure zoning on each Fibre Channel switch.

See the Dell Storage Center SCv2000/SCv2020 Storage System Deployment Guide for information about setting up Fibre Channel zoning.

Table 6. Physical WWNs in Fault Domain 1
Physical WWN of storage controller 1: port 1 ________________
Physical WWN of storage controller 2: port 1 ________________
(4-port I/O card only) Physical WWN of storage controller 1: port 3 ________________
(4-port I/O card only) Physical WWN of storage controller 2: port 3 ________________
Table 7. Virtual WWNs in Fault Domain 1
Virtual WWN of storage controller 1: port 1 ________________
Virtual WWN of storage controller 2: port 1 ________________
(4-port I/O card only) Virtual WWN of storage controller 1: port 3 ________________
(4-port I/O card only) Virtual WWN of storage controller 2: port 3 ________________
Table 8. Physical WWNs in Fault Domain 2
Physical WWN of storage controller 1: port 2 ________________
Physical WWN of storage controller 2: port 2 ________________
(4-port I/O card only) Physical WWN of storage controller 1: port 4 ________________
(4-port I/O card only) Physical WWN of storage controller 2: port 4 ________________
Table 9. Virtual WWNs in Fault Domain 2
Virtual WWN of storage controller 1: port 2 ________________
Virtual WWN of storage controller 2: port 2 ________________
(4-port I/O card only) Virtual WWN of storage controller 1: port 4 ________________
(4-port I/O card only) Virtual WWN of storage controller 2: port 4 ________________

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\