Ana içeriğe atla
Oturumu Kapat

Dell'e Hoş Geldiniz

Hesabım
  • Hızla ve kolayca sipariş verin
  • Siparişleri görüntüleyin ve kargonuzun durumunu izleyin
  • Ürünlerinizin listesini oluşturun ve listeye erişin
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Oturum Aç Hesap oluşturun Premier Oturum Açma İş Ortağı Programı Oturum Açma
Bize Ulaşın

Integrated Dell Remote Access Controller 7 (iDRAC7) Version 1.50.50 User's Guide

PDF

Modifying Network Settings Using Local RACADM

To generate a list of available network properties, type the following:
  • NOTE: You can use either getconfig and config commands or get and set commands with the RACADM objects.
  • Using getconfig command: racadm getconfig -g cfgLanNetworking
  • Using get command: racadm get iDRAC.Nic
To use DHCP to obtain an IP address, use the following command to write the object cfgNicUseDhcp or DHCPEnable and enable this feature:
  • Using config command: racadm config -g cfgLanNetworking -o cfgNicUseDHCP 1
  • Using set command: racadm set iDRAC.IPv4.DHCPEnable 1
The following is an example of how the command may be used to configure the required LAN network properties:
  • Using config command: 
    racadm config -g cfgLanNetworking -o cfgNicEnable 1
                                          racadm config -g cfgLanNetworking -o cfgNicIpAddress 192.168.0.120
                                          racadm config -g cfgLanNetworking -o cfgNicNetmask 255.255.255.0
                                          racadm config -g cfgLanNetworking -o cfgNicGateway 192.168.0.120
                                          racadm config -g cfgLanNetworking -o cfgNicUseDHCP 0
                                          racadm config -g cfgLanNetworking -o cfgDNSServersFromDHCP 0
                                          racadm config -g cfgLanNetworking -o cfgDNSServer1 192.168.0.5
                                          racadm config -g cfgLanNetworking -o cfgDNSServer2 192.168.0.6
                                          racadm config -g cfgLanNetworking -o cfgDNSRegisterRac 1
                                          racadm config -g cfgLanNetworking -o cfgDNSRacName RAC-EK00002
                                          racadm config -g cfgLanNetworking -o cfgDNSDomainNameFromDHCP 0
                                          racadm config -g cfgLanNetworking -o cfgDNSDomainName MYDOMAIN
  • Using set command: 
    racadm set iDRAC.Nic.Enable 1
                                          racadm set iDRAC.IPv4.Address 192.168.0.120
                                          racadm set iDRAC.IPv4.Netmask 255.255.255.0
                                          racadm set iDRAC.IPv4.Gateway 192.168.0.120
                                          racadm set iDRAC.IPv4.DHCPEnable 0
                                          racadm set iDRAC.IPv4.DNSFromDHCP 0
                                          racadm set iDRAC.IPv4.DNS1 192.168.0.5
                                          racadm set iDRAC.IPv4.DNS2 192.168.0.6
                                          racadm set iDRAC.Nic.DNSRegister 1
                                          racadm set iDRAC.Nic.DNSRacName RAC-EK00002
                                          racadm set iDRAC.Nic.DNSDomainFromDHCP 0
                                          racadm set iDRAC.Nic.DNSDomainName MYDOMAIN
  • NOTE: If cfgNicEnable or iDRAC.Nic.Enable is set to 0, the iDRAC7 LAN is disabled even if DHCP is enabled.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\