Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.

Dell EMC PowerEdge MX740c Installation and Service Manual

General memory module installation guidelines

To ensure optimal performance of your system, observe the following general guidelines when configuring your system memory. If your system's memory configurations fail to observe these guidelines, your system might not boot, stop responding during memory configuration, or operate with reduced memory.

The memory bus may operate at frequency can be 3200 MT/s*, 2933 MT/s, 2666 MT/s, 2400 MT/s, or 2133 MT/s depending on the following factors:
  • System profile selected (for example, Performance Optimized, or Custom [can be run at high speed or lower])
  • Maximum supported DIMM speed of the processors.
  • Maximum supported DIMM speed of the processors.
  • Maximum supported speed of the DIMMs
NOTE MT/s indicates DIMM speed in MegaTransfers per second.
NOTE 3200*-Memory speed will be limited to 2933MT/s due to processor limitations.

The system supports Flexible Memory Configuration, enabling the system to be configured and run in any valid chipset architectural configuration. The following are the recommended guidelines for installing memory modules:

  • All DIMMs must be DDR4.
  • RDIMMs and LRDIMMs must not be mixed.
  • 64 GB LRDIMMs that are DDP (Dual Die Package) LRDIMMs must not be mixed with 128 GB LRDIMMs that are TSV (Through Silicon Via/3DS) LRDIMMs.
  • x4 and x8 DRAM based memory modules can be mixed.
  • Up to two RDIMMs can be populated per channel regardless of rank count.
  • Up to two LRDIMMs can be populated per channel regardless of rank count.
  • A maximum of two different ranked DIMMs can be populated in a channel regardless of rank count.
  • If memory modules with different speeds are installed, they will operate at the speed of the slowest installed memory module(s).
  • Populate memory module sockets only if a processor is installed.
    • For single-processor systems, sockets A1 to A12 are available.
    • For dual-processor systems, sockets A1 to A12 and sockets B1 to B12 are available.
  • Populate all the sockets with white release tabs first, followed by the black release tabs.
  • When mixing memory modules with different capacities, populate the sockets with memory modules with the highest capacity first.
    NOTE For example, if you want to mix 8 GB and 16 GB memory modules, populate 16 GB memory modules in the sockets with white release tabs and 8 GB memory modules in the sockets with black release tabs.
  • Memory modules of different capacities can be mixed provided other memory population rules are followed.
NOTE For example, 8 GB and 16 GB memory modules can be mixed.
  • In a dual-processor configuration, the memory configuration for each processor must be identical.
    NOTE For example, if you populate socket A1 for processor 1, then populate socket B1 for processor 2, and so on.
  • Mixing of more than two memory module capacities in one systems is not supported.
  • Unbalanced memory configurations will result in a performance loss so always populate memory channels identically with identical DIMMs for best performance.
  • Populate six identical memory modules per processor (one DIMM per channel) at a time to maximize performance.
DIMM population update for Performance Optimized mode with quantity of 4 and 8 DIMMs per processor.
  • When the DIMM quantity is 4 per processor, the population is slot 1, 2, 4, 5.
  • When the DIMM quantity is 8 per processor, the population is slot 1, 2, 4, 5, 7, 8, 10, 11.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\