- Notes, Cautions, and Warnings
- About This Guide
- About the SCv3000 and SCv3020 Storage System
- Storage Center Hardware Components
- Storage Center Communication
- Front-End Connectivity
- Back-End Connectivity
- System Administration
- Storage Center Replication
- SCv3000 and SCv3020 Storage System Hardware
- SCv3000 and SCv3020 Storage System Front-Panel View
- SCv3000 and SCv3020 Storage System Back-Panel View
- Expansion Enclosure Overview
- Install the Storage Center Hardware
- Connect the Front-End Cabling
- Types of Redundancy for Front-End Connections
- Connecting to Host Servers with Fibre Channel HBAs
- Connecting to Host Servers with iSCSI HBAs or Network Adapters
- Connecting to Host Servers with SAS HBAs
- Attach Host Servers (Fibre Channel)
- Attach the Host Servers (iSCSI)
- Attach the Host Servers (SAS)
- Connect the Management Ports to the Management Network
- Connect the Back-End Cabling
- Deploy the Storage Center
- Preparing for Deployment
- Deploying the Storage Center Using Unisphere
- Unisphere Discovery Utility
- Deploying the Storage Center Using Storage Manager Client
- Install and Use the Storage Manager Client
- Introduction to Storage Center Initial Configuration
- Select a Storage Center to Initialize
- Welcome Page
- Customer Installation Authorization
- Set System Information
- Set Administrator Information
- Confirm the Storage Center Configuration
- Deploy the Storage Center
- Configure Key Management Server Settings
- Create a Storage Type
- Fault Tolerance
- Inherit Settings
- Configure Time Settings
- Configure SMTP Server Settings
- Set Up SupportAssist
- Accept the SupportAssist Collection Agreement
- Provide Contact Information
- Provide Site Contact Information
- Validate the SupportAssist Connection
- Update Storage Center
- Complete Configuration and Perform Next Steps
- Perform Post-Setup Tasks
- Adding or Removing Expansion Enclosures
- Adding Expansion Enclosures to a Storage System Deployed Without Expansion Enclosures
- Install New SCv300 and SCv320 Expansion Enclosures in a Rack
- Add the SCv300 and SCv320 Expansion Enclosures to the A-Side of the Chain
- Add the SCv300 and SCv320 Expansion Enclosures to the B-Side of the Chain
- Install New SCv360 Expansion Enclosures in a Rack
- Add the SCv360 Expansion Enclosures to the A-Side of the Chain
- Add an SCv360 Expansion Enclosure to the B-Side of the Chain
- Adding a Single Expansion Enclosure to a Chain Currently in Service
- Removing an Expansion Enclosure from a Chain Currently in Service
- Release the Drives in the Expansion Enclosure
- Disconnect the SCv300 and SCv320 Expansion Enclosure from the A-Side of the Chain
- Disconnect the SCv300 and SCv320 Expansion Enclosure from the B-Side of the Chain
- Disconnect the SCv360 Expansion Enclosure from the A-Side of the Chain
- Disconnect the SCv360 Expansion Enclosure from the B-Side of the Chain
- Adding Expansion Enclosures to a Storage System Deployed Without Expansion Enclosures
- Troubleshooting Storage Center Deployment
- Set Up a Local Host or VMware Host
- Worksheet to Record System Information
SCv3000 and SCv3020 Storage System Deployment Guide
Confirm the Storage Center Configuration
Make sure that the configuration information shown on the Confirm Configuration page is correct before continuing. If you selected DHCP IPv4 as the network configuration source, the dynamically assigned IP addresses are displayed on this page.
Steps
- Verify that the Storage Center settings are correct.
- If the configuration information is correct,
click Apply Configuration.
If the configuration information is incorrect, click Back and provide the correct information.
NOTE: After you click the Apply Configuration button, the configuration cannot be changed until after the Storage Center is fully deployed.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\