- Notes, cautions, and warnings
- Dell PowerEdge M830 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing blade components
- Safety instructions
- Recommended tools
- Removing and installing a blade
- System cover
- Inside the blade
- Cooling shroud
- System memory
- I/O module mezzanine cards
- Mezzanine card support bracket
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network daughter card
- Processor blank and DIMM blank
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive or SSD
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Hard-drive or SSD cage
- Hard-drive or SSD backplane
- Removing a 2.5-inch (x4) SAS hard-drive or SSD backplane
- Installing a 2.5-inch (x4) SAS hard-drive or SSD backplane
- Removing a 2.5-inch (x4) SATA hard-drive or SSD backplane
- Installing a 2.5-inch (x4) SATA hard-drive or SSD backplane
- Removing a 2.5-inch (x2) SATA hard drive or SSD plus 2.5-inch (x2) PCIe SSD backplane
- Installing a 2.5-inch (x2) SATA hard drive or SSD plus 2.5-inch (x2) PCIe SSD backplane
- Removing a 1.8-inch (x12) SAS SSD backplane
- Installing a 1.8-inch (x12) SAS SSD backplane
- System battery
- Storage controller card
- Expander card
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Dell PowerEdge M830 Owner's Manual
Replacing the SD vFlash card
Prerequisites
CAUTION: Many
repairs may only be done by a certified service technician. You should
only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by
Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
- Follow the safety guidelines listed in the Safety instructions section.
- Follow the procedure listed in the Before working inside your system section.
Steps
- If installed, remove the SD vFlash card from
the card slot.NOTE: The SD vFlash card slot is below the NDC.
Figure 1. Removing the SD vFlash card 
- SD vFlash card
- SD vFlash card slot
- SD vFlash card slot identification label
- Insert the contact-pin end of the SD card
into the card slot on the vFlash media unit.NOTE: The slot is keyed to ensure correct insertion of the card.
- Press inward on the card to lock it into
the slot.
Figure 2. Installing the SD vFlash card 
- SD vFlash card
- SD vFlash card slot
Next steps
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\