- Notes, cautions, and warnings
- Dell PowerEdge C6320p overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Updating the Fan Control Board firmware
- Prerequisites for installing and removing components
- Installing and removing sled components
- Inside the system
- PowerEdge C6320p sled
- Air shroud
- System memory
- 1.8-inch Solid State Drive
- SATA cable removal and installation for the sled
- Processor and heat sink module
- Removing the fabric cable from the processor
- Connecting the fabric cable to the processor
- Removing the processor and heat sink module
- Installing the processor and heat sink module
- Removing the fabric processor from the processor heat sink module
- Installing the fabric processor into the processor heat sink module
- Removing the non fabric processor from the processor heat sink module
- Installing the non fabric processor into the processor and heat sink module
- Expansion card assembly and expansion card
- PCIe slot priority
- Removing the expansion card riser assembly
- Installing the expansion card riser assembly
- Removing an expansion card
- Installing an expansion card
- Removing the riser card
- Installing the riser card
- Removing the cables from the fabric carrier card
- Connecting the cables to the fabric carrier card
- Mezzanine cards and mezzanine bridge card
- System battery
- Trusted Platform Module
- System board
- SAS connector protector
- Installing and removing enclosure components
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting a micro SD card
- Troubleshooting a drive or SSD
- Troubleshooting expansion cards
- Troubleshooting processors
- System messages
- Getting help
Dell PowerEdge C6320p Owner's Manual
Checking the FCB firmware version
Steps
Check the fan control board (FCB) firmware
version by executing this IPMI command ipmitool
–U server_user_name –P server_user_pass_word –H server_IP –I lanplus
raw 0x30 0x12. For example, to check the FCB firmware version
v3.09, execute this command:
ipmitool –U root –P calvin –H 10.3.25.127 –I lanplus raw 0x30 0x12Response: 01 69 1b 03 09 06 26 00 00 04 ff 00 01 2a 2f ff ff 0f c2 00 00 01 04 01 04 31 c5 11 ff 0f
NOTE:
- The FCB version will be listed in the 4th and 5th bytes (from the left) of the output. In this output, 03 09 (4th and 5th bytes from the left) indicates the FCB version.
- The fan table version is listed in the 6th byte of the output. In this output, 06 (6th byte from the left) indicates the fan table version.
- The node slot is listed in the 10th byte of the output. In this output, 04 (10th byte from the left) indicates the node slot.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\