Removal
Base Cover
Identify the base cover highlighted in blue.
Loosen the captive screws that secure the base cover.
Pry the base cover near the hinges to release it from the system.
Lift the base cover off the palm rest assembly.
Battery Cable
Identify the battery cable highlighted in blue.
Using the pull tab, lift up to disconnect the battery cable from the system board.
Press and hold the power button for 10 seconds to ground the system and remove residual static electricity.
Battery
Identify the battery highlighted in blue.
Loosen the captive screws that secure the battery.
Lift the battery out of the system.
Wireless Module (WLAN)
Identify the wireless module (WLAN) highlighted in blue.
Loosen the captive screw that secures the WLAN card bracket.
Remove the bracket to access the WLAN cables.
Disconnect the antenna cables (black and white cables) from the WLAN.
Slide and remove the WLAN card from the connector.
SSD 2230
Identify the solid state drive (SSD) highlighted in blue.
Remove the screws that secure the SSD bracket on the system board.
Lift the solid state drive thermal shield off the system.
Slide and lift the solid state drive off the system.
Chassis frame
Identify the chassis frame highlighted in blue.
Unroute the antenna cables from the guides on the frame.
Disconnect the speaker cable from the system board.
Unroute the speaker cable from the chassis frame.
Remove the screws that secure the chassis frame to the system.
Lift to remove the chassis frame.
Speaker
Identify the speaker highlighted in blue.
Disconnect the speaker cable from the system board.
Remove the white WLAN antenna cable from the routing guides.
Remove the speaker cables from the routing guides.
Lift the right and left speakers, along with its cable, off the system.
Smart card reader
Identify the smart card reader highlighted in blue.
Lift latch and disconnect the smart card cable from the USH board.
Peel the smart card reader cable.
Remove the screws that secure the smart card reader to the system.
Lift the smart card reader along the cable from the system.
Install
Smart card reader
Identify the smart card reader location highlighted in blue.
Install the smart card reader into the slot to align with the tabs on the system.
Install the screws to secure the smart card reader to the system.
Adhere the smart card reader cable to the palm-rest assembly.
Connect the smart card cable to the USH board. Close the latch to secure.
Speaker
Identify the speaker location highlighted in blue.
Using the alignment posts, install the speakers into their slots on the system.
Route the white antenna cable through the routing guides on the system.
Route the speaker cables through the routing guides on the system.
Connect the speaker cable to the system board.
Chassis frame
Identify the chassis frame location highlighted in blue.
Align and place the chassis frame on the system chassis.
Install the screws to secure the chassis frame to the system.
Route the speaker cable along the chassis frame.
Connect the speaker cable to the system board.
Route the antenna cables through guides on the frame.
SSD 2230
Identify the solid state drive (SSD) location highlighted in blue.
Slide the SSD into the slot on the system board.
Align the screw holes on the solid state drive bracket with the screw holes on the system board.
Install the screws to secure the SSD bracket to the system board.
Wireless Module (WLAN)
Identify the wireless module (WLAN) location highlighted in blue.
Insert the WLAN into the connector on the system board.
Connect the black cable to the auxiliary (black triangle).
Connect the white cable to the main (white triangle).
Install the bracket to secure the antenna cables.
Tighten the captive screw to secure the WLAN card bracket.
Battery
Identify the battery location highlighted in blue.
Install the battery into the slot on the system, aligning the screw holes.
Tighten the captive screws to secure the battery in place.
Battery Cable
Identify the battery cable location highlighted in blue.
Connect the battery cable to the system board.
Base Cover
Identify the base cover location highlighted in blue.
Align the base cover tabs to the slots, press the cover until it clicks into place.
Tighten the captive screws that secure the base cover to the system.