Removal
System Cover
Identify the system cover highlighted in blue.
Using a flat head or a Phillips screwdriver, rotate the lock counter clockwise.
Lift the latch until the system cover slides back.
Hold the cover on both sides, and lift the cover away from the system.
BOSS-N1 card carrier
Identify the BOSS-N1 card carrier highlighted in blue.
Pull and lift the BOSS-N1 card carrier retention latch lock to open.
Slide the BOSS-N1 card carrier out.
BOSS-N1 Module
Identify the BOSS-N1 Module highlighted in blue.
Remove the BOSS-N1 power and signal cable from the BOSS-N1 module.
Remove the screw that secures the BOSS-N1 module on the riser 1.
Slide the BOSS-N1 module toward the front of the chassis and lift the module.
Air shroud
Identify the air shroud highlighted in blue.
Holding the edges of the air shroud, lift the air shroud out of the system.
Riser 1B
Identify the riser 1B highlighted in blue.
Using a Phillips screwdriver, loosen the blue thumb screw on the riser.
Disconnect any cables that are connected to the expansion card or the riser.
Press the blue release tab or blue button on the riser.
Holding the edges, lift the expansion card riser from the riser connector on the system board.
Riser 3B
Identify the riser 3B highlighted in blue.
Using a Phillips screwdriver, loosen the blue thumb screw on the riser.
Press the blue release tab or blue button on the riser.
Holding the edges, lift the expansion card riser from the riser connector on the system board.
Riser 2A
Identify the riser 2A highlighted in blue.
Press the blue release tab or blue button on the riser.
Holding the edges, lift the expansion card riser from the riser connector on the system board.
System battery
Identify the system battery highlighted in blue.
Use a plastic scribe to pry out the system battery.
Lift the battery out of the socket.
Install
System battery
Identify the system battery location highlighted in blue.
Install the battery with the "+" facing up and slide it under the securing tabs.
Press the battery into the connector until it snaps into place.
Riser 2A
Identify the riser 2A location highlighted in blue.
Holding the edges, insert the riser into place and press the touch points until the riser is fully seated.
Riser 3B
Identify the riser 3B location highlighted in blue.
Holding the edges, insert the riser into place and press the touch points until the riser is fully seated.
Using a Phillips screwdriver, tighten the blue thumb screw to secure the riser on the chassis.
Riser 1B
Identify the riser 1B location highlighted in blue.
Holding the edges, insert the riser into place and press the touch points until the riser is fully seated.
Using a Phillips screwdriver, tighten the blue thumb screw to secure the riser on the chassis.
Connect the cables to the expansion card on the riser.
Air shroud
Identify the air shroud location highlighted in blue.
Tilt at an angle and align the tabs with the slots on the system and place the air shroud until it is firmly seated.
BOSS-N1 Module
Identify the BOSS-N1 Module location highlighted in blue.
Install the BOSS-N1 module and push horizontally towards the rear of the system untill firmly seated.
Install the screw that secures the BOSS-N1 module to the riser 1.
Connect the BOSS-N1 power and signal cables to the connectors on the BOSS-N1 module.
BOSS-N1 card carrier
Identify the BOSS-N1 card carrier location highlighted in blue.
Slide the BOSS-N1 card carrier into the BOSS-N1 module slot.
Close the BOSS-N1 card carrier release latch to lock the carrier in place.
System Cover
Identify the system cover location highlighted in blue.
Align the tabs on the system cover with the guide slots on the system and slide the system cover.
Close the system cover release latch.
Using a flat head or Phillips screwdriver, rotate the lock clockwise to the lock position.