Search Results (188)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
Good morning all,can anyone give me some advice please?.Question is can I get over 2GB Ram on my Dell Latitude D610.3GB of ram would be ideal if possible.Regards,Jason
Question
•
FluidFS
Community Accepted Solution
Hello, I am new around these forums and had a question with regards to updating the MD3000i. I am currently running a unit with two controllers on the following version: Firmware version: 07.35.22.61 NVSRAM version: N1532-735890-004 EMW version: 03.35.G6.50
Question
•
FluidFS
Community Accepted Solution
I have (2) PS6000 arrays in a group. One array makes up my default storage pool. The second array I just added and created a new pool (maint). My default pool is RAID 5. My maint pool is RAID 6. I'm trying to move a volume from my default pool to my maint pool. Everyth
Question
•
FluidFS
Community Accepted Solution
Hello, I've got a PowerEdge T310 with 4 hotswap drives (raid 6), and its running dangerously low on space.. Can I just purchase 4 new larger drives, and (one-by-one) replace the old ones? Can I expand the virtual drive or will I have to create a second virtual drive with the new free space? Than
Question
•
FluidFS
Community Accepted Solution
Hi. We are looking into buying a Dell Compellent Array, but before that im looking into its technology. Unfortunately the few public datasheets on the SC8000 are very brief. Im looking into information how the array handles its raids, from what ive understood, when you create a volume, some dat
Question
•
FluidFS
Community Accepted Solution
Is it possible to have a RAID 5 Virtual Disk on a PERC 6/i Card with 2 disks of 500 Go and 1 disk of 1 To ?It's not a matter if, on the third disk, only 500 Go will be used.All disks are 3.5 inch, NearLine SAS and 7200 rpm Thank You Philippe
Question
•
FluidFS
Community Accepted Solution
Hi Dell Team, Just want to confirm If we have Rapid Deployment Guide for Compellent SC8000. We have incoming deployment next month for this storage and we need to prepare ourselves and learn on how to setup and configure the storage array. http://i.dell.com/sites/doccontent/shared-content/services
Question
•
FluidFS
Community Accepted Solution
GroupManager displays different number of replicas, 2 outbound and 1 inbound. Is this normal behavior?
Question
•
FluidFS
Community Accepted Solution
Hi all, I am developing a script to retrieve information about the replicas done between two Dell EQL PS Series arrays. For each volume, I am keeping a history of 10 replicas, i use this following command to display all the replicas done for a specific volume. > get-eqlreplica -GroupName SANPR
Question
•
FluidFS
Community Accepted Solution
Hi, hope someone can offer some assistance. We have a MD3000 which was configured with 1 virtual disk including 1 hot standby, connected to VMWare which held all the virtual machine files. the disk group is named DG0 at RAID 5 and the virtual disk vd0. Recently we had a disk failure which kicked in
Question
•
FluidFS
Community Accepted Solution
Hi. I have a Dell EqualLogic 6010 collecting dust in my test lab. It was sent from another office for unknown reasons. I would like to utilize this device to offload some developmental vm backup copies from our san to this smaller 16 drive device. I only have one switch that came with it, but for t
Question
•
FluidFS
Community Accepted Solution
Hello, Because of cost savings, we are integrating 1x Dell Equallogic ps6100x (2 controllers with each 4 ports) 3x dell poweredge r720 (each have 2 ports dedicated for SAN storage trafic) vSphere 5.5 (shared storage on the SAN) Without the use of SAN switches. Each host has dual direct connecti
Question
•
FluidFS
Community Accepted Solution
One of the nice new functions of SANHQ is advertised as allowing me to see on what ISCSI connections i have retransmits. That function does not seem to be in 3.0 EPA. or atleast it requires something that im not compliant on. My envoriment is running 6.0.7 If i look in iscsi connections i s
Question
•
FluidFS
Community Accepted Solution
Our MD3000i keeps saying the array is not optimal and that a virtual disk is not on preferred path. We have two RAID sets on it with one VD each. The first says its preferred path is Controller 0, the second says its preferred path is controller 1. But controller 0 likes to take over both.
Question
•
FluidFS
Community Accepted Solution
Hi I have got an customer that have a hugh number of equallogic boxes. Some with SSD, some with SAS and some with SATA drive. The customer want to control whats located where.So he could take the SQL servers of there and put it on a faster disk drives. I know the command bind running from the CL
Question
•
FluidFS
Community Accepted Solution
With the impending release of Server 2012 R2, when can we expect a supported HIT/ME?
Question
•
FluidFS
Community Accepted Solution
Hi all, I hope one of the Dell technicians on here are able to help, I'm monitoring one of our Dell Storage appliances a Dell MD3600f through SMcli, and I'm checking the Storage array health status = optimal. But what I wanted to ask what exactly does optimal means what sensors is it checking, o
Question
•
FluidFS
Community Accepted Solution
Dears, We need to move a member -Member3- to a maintenance pool for upgrading the firmware. My question is how can we calculate the needed space to move a member to another pool ? I attached some photos from SANHQ for the Group/Pool/Member capacity. P.S. Consider the group space not the
Question
•
FluidFS
Community Accepted Solution
Hi, I have Equallogic PS6100 and wanted to know if Dell EqualLogic Multipathing Extension Module v1.1.2 will work in ESXi 5.5? If no when can we expect the plugin to be updated. Thanks, Bala
Question
•
FluidFS
Community Accepted Solution
Hi all, I'm hoping someone is able to help, I'm after a SMcli for linux in order to be able to monitor one of our new PowerVault MD3600f boxes. I've managed to find a version on the net but it doesn't work, the error message is below, I've checked Dell drivers and it doesn't list anything for my p
Question
•
FluidFS